Difference between revisions of "EPD-320 application tech"

From ESS-WIKI
Jump to: navigation, search
 
Line 1: Line 1:
 
= EPD-320 Application guide =
 
= EPD-320 Application guide =
  
This application provide user a way that image full update and carousel mode for EPD-320 panel display. user only write xml file follow setting rule.
+
This application provide user a way that image full update and carousel mode for EPD-320 panel display. user configure xml file follow setting rule.
  
 
== Components LIST ==
 
== Components LIST ==
Line 106: Line 106:
  
 
4.Repeat step 3 replace others ITE T-CON driver.
 
4.Repeat step 3 replace others ITE T-CON driver.
 +
 +
Contact with Advantech get software package
  
 
==== Linux ====
 
==== Linux ====
Line 114: Line 116:
  
 
2. Installed OpenCV 2.4.13.
 
2. Installed OpenCV 2.4.13.
 +
 +
3. libjepg
 +
 +
Contact with Advantech get software package
  
 
==== OpenWrt ====
 
==== OpenWrt ====
  
software package has been integrate to latest Firmware on Hardware model of WISE-3270. Others hardware platform need install OpenCV, libusb library in system.
+
software package has been integrate to latest Firmware on Hardware model of WISE-3270. Others hardware platform need install OpenCV, libusb , libjepg library on system.
  
 
=== Xml format ===
 
=== Xml format ===
Line 144: Line 150:
 
'''<image path> : ''' User should assign photo image path in operating system , application search image file under this path.
 
'''<image path> : ''' User should assign photo image path in operating system , application search image file under this path.
  
'''&lt;img&gt;&nbsp;:''' User have to write the image name in xml file and application follow path and name to load image file. It can be assigned more than one <img> tag name between <full_update> and </full_update> then following <img> tag to load image and display in sequence.
+
'''&lt;img&gt;&nbsp;:''' User have to write the image name in xml file and application follow path and name to load image file. It can be assigned more than one &lt;img&gt; tag name between &lt;full_update&gt; and &lt;/full_update&gt; then following &lt;img&gt; tag to load image and display in sequence.
  
 
'''&lt;stop&gt;''' Stop tag use to load image at once. Above mention stop tag in xml, application terminated after 1.bmp update done. In carousel mode stop tag must removed from xml.
 
'''&lt;stop&gt;''' Stop tag use to load image at once. Above mention stop tag in xml, application terminated after 1.bmp update done. In carousel mode stop tag must removed from xml.
Line 150: Line 156:
 
'''&lt;slide_interval&gt;:''' Slide interval is delay time in second between every image display.
 
'''&lt;slide_interval&gt;:''' Slide interval is delay time in second between every image display.
  
'''&lt;set_temperature&gt;''' user don't need config temperature.
+
'''&lt;set_temperature&gt;''' user don't need configure temperature.
  
 
'''&lt;waveform_mode&gt;''' Waveform mode usually choose mode 2 for image update. waveform explicit detail see [[EPD-320_application_tech#Waveform_mode|Section 1.4 waveform mode]]
 
'''&lt;waveform_mode&gt;''' Waveform mode usually choose mode 2 for image update. waveform explicit detail see [[EPD-320_application_tech#Waveform_mode|Section 1.4 waveform mode]]
Line 166: Line 172:
 
3. Execute command EPD_4TCON with parameter xml file name
 
3. Execute command EPD_4TCON with parameter xml file name
  
Windows&nbsp;: '''"EPD_4Tcon test.xml"'''
+
Windows&nbsp;: '''"EPD_4Tcon.exe test.xml"'''
  
 
Linux&nbsp;: $'''./EPD_4Tcon test.xml'''
 
Linux&nbsp;: $'''./EPD_4Tcon test.xml'''
  
[[File:Epd320 6 1.jpg|500px|execute EPD4tcon]]
+
<!--[[File:Epd320 6 1.jpg|500px|execute EPD4tcon]]-->

Latest revision as of 08:19, 27 March 2020

EPD-320 Application guide

This application provide user a way that image full update and carousel mode for EPD-320 panel display. user configure xml file follow setting rule.

Components LIST

Item

 Description
1  32” EPAPER
2  EPD-320 PCBA
3  cable

RTENOTITLE

SYSTEM ARCHITECURE

system diagram

System support

Host operating system: linux(ubuntu)、OpenWrt、windows(windows 7 or windows 10)

Waveform mode

There are six Waveform mode for image update and short name as below table. The mode parameter will use in update command.

mode 0 mode 1 mode 2 mode 3 mode 4 mode 5
INIT DU GC16 GCC16 A2 GL16

INIT(Global update WF) :

Initialize is used to completely clear the display, if it's left in an unknown state (i.e. if the previous image has been lost by a re-boot)

DU(Local update WF) :

Direct update Non-flashing waveform that can be used to update. it can update any changed graytone pixel to black or white only.

GC16(Global update WF) :

Grayscale clear, 16 levels A "flashy" waveform used for 16 level grayscale images. All the pixels are updated or cleared

GCC16( Global clear update WF) :

Grayscale Clear, 16 Levels A "more flashy" waveform used for 16 level grayscale images. All the pixels are updated or cleared.
This provides the best image appearance.

A2(Local update WF) :

animation, 2 Levels is a non-flashing waveform that can be used for fast updates and simple animation.
This wave form support black & white updates only.
image quality and ghosting is reduced in exchange for the response time.

GL16(Local update WF when white to white , Global update when 16 gray levels) :

The GL16 waveform is used to update anti-aliased text with reduced flash. GL16 should bed used only with Full Display Update..
The entire display except pixels staying in white will update as the new image is written. The GL16 waveform has 16 unique gray levels.

Push image application

Hardware prepare

1. Connected EPD FPC to mainboard

2. Connected micro USB cable to mainboard USB2(CN2) , usb port connect to computer usb port which installed windows or linux ubuntu

3. Connected 12V power cable to mainboard.

system diagram2

Software prepare

Windows

1. Download usb driver tool | zadig usb tool

2.Execute zadig.exe and click Option->List All Devices

3.ITE T-CON appeared in list and click Replace Driver button , waiting installation until success

driver install

4.Repeat step 3 replace others ITE T-CON driver.

Contact with Advantech get software package

Linux

User must install library as below

1. Installed libusb 1.0.22.

2. Installed OpenCV 2.4.13.

3. libjepg

Contact with Advantech get software package

OpenWrt

software package has been integrate to latest Firmware on Hardware model of WISE-3270. Others hardware platform need install OpenCV, libusb , libjepg library on system.

Xml format

Below is content of xml file include image update parameter.

 <?xml version="1.0"?> 
 <epd_config>
   <epd name="EPD 31.2">
       <color>KW</color>	    
       <image_path>D:\application\photoImg\</image_path>
       <image_name>
         <full_update>
             <img>1.bmp</img>
         </full_update>
         <stop>stop</stop>
       </image_name>
       <slide_interval>0</slide_interval>
       <en_set_temperature>0</en_set_temperature> 
       <temperature>25</temperature>
       <waveform_mode>2</waveform_mode>
       <rotate>180</rotate>
 </epd>
 </epd_config>

<image path> : User should assign photo image path in operating system , application search image file under this path.

<img> : User have to write the image name in xml file and application follow path and name to load image file. It can be assigned more than one <img> tag name between <full_update> and </full_update> then following <img> tag to load image and display in sequence.

<stop> Stop tag use to load image at once. Above mention stop tag in xml, application terminated after 1.bmp update done. In carousel mode stop tag must removed from xml.

<slide_interval>: Slide interval is delay time in second between every image display.

<set_temperature> user don't need configure temperature.

<waveform_mode> Waveform mode usually choose mode 2 for image update. waveform explicit detail see Section 1.4 waveform mode

<rotate> There are 4 options 0 、90、180、270 angle to choose and rotate image following angle.

Application execution

User should check all information of xml is correct before execute application or it may cause error procedure.

1. Open command line

2. Change current directory to EPD_4TCON

3. Execute command EPD_4TCON with parameter xml file name

Windows : "EPD_4Tcon.exe test.xml"

Linux : $./EPD_4Tcon test.xml