AFE-R761 CAN/DEBUG - Revision history

Xingxing.li at 01:56, 13 January 2026

2026-01-13T01:56:39Z

Xingxing.li at 01:46, 13 January 2026

2026-01-13T01:46:51Z

Xingxing.li: Created page with " === '''Hardware Pin Definition：''' === {| border="1" cellpadding="1" cellspacing="1" style="width: 299px;" |- | colspan="2" style="width: 289px;" | '''CAN/DEBUG Connector'..."

2026-01-13T01:44:27Z

Created page with " === '''Hardware Pin Definition：''' === {| border="1" cellpadding="1" cellspacing="1" style="width: 299px;" |- | colspan="2" style="width: 289px;" | '''CAN/DEBUG Connector'..."

New page

=== '''Hardware Pin Definition：''' ===

{| border="1" cellpadding="1" cellspacing="1" style="width: 299px;"
|-
| colspan="2" style="width: 289px;" | '''CAN/DEBUG Connector'''
|-
| style="width: 83px;" | '''Pin'''
| style="width: 200px;" | '''Pin Name'''
|-
| style="width: 83px;" | 1
| style="width: 200px;" | TX_DEBUG
|-
| style="width: 83px;" | 2
| style="width: 200px;" | RX_DEBUG
|-
| style="width: 83px;" | 3
| style="width: 200px;" | GND
|-
| style="width: 83px;" | 4
| style="width: 200px;" | GND
|-
| style="width: 83px;" | 5
| style="width: 200px;" | CAN2_H
|-
| style="width: 83px;" | 6
| style="width: 200px;" | CAN2_L
|-
| style="width: 83px;" | 7
| style="width: 200px;" | CAN1_H
|-
| style="width: 83px;" | 8
| style="width: 200px;" | CAN1_L
|}

=== '''Debug Port Connection：''' ===

1. Connect the debug port cable (1700035538-01) to the Debug port on ASRA501.

2. Connect it to your PC using the USB to RS-232 Cable.

=== '''Debug Port Settings：''' ===

AFE-R761 can communicate with a host server using serial cables. Common serial communication programs such as HyperTerminal, Tera Term, or PuTTY can be used in these applications. The example below describes the serial terminal setup using<br/> HyperTerminal on a Windows host:<br/> 1. Connect AFE-R761 with your PC using a serial cable.<br/> 2. Open HyperTerminal on your Windows PC, and select the settings demon�strated in the photo below.

3. Insert power adapter to DC jack and power up the board. The Debug console log will be displayed on the terminal screen.

=== '''CAN''' ===

AFE-R761 has two CAN ports.<br/> Use the "candump" and "cansend" tools directly to send and receive messages. The tools have been embedded into the system.

==== '''Check network ports''' ====

Check network ports of can0 and can1：
<pre># ifconfig -a
… …
can0: flags=193<UP,RUNNING,NOARP> mtu 16
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 10 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

can1: flags=193<UP,RUNNING,NOARP> mtu 16
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 10 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

… …
</pre>

=== '''Configure''' ===

Use “ip” command to configure can port. See details of the usage of “ip link”:
<pre># ip link help
… …
ip link set { DEVICE | dev DEVICE | group DEVGROUP }
[ { up | down } ]
[ type TYPE ARGS ]
… …
</pre>
<pre># ip link help can
… …
ip link set DEVICE type can
[ bitrate BITRATE [ sample-point SAMPLE-POINT] ] |
[ dbitrate BITRATE [ dsample-point SAMPLE-POINT] ] |
[ fd { on | off } ]
… …
</pre>

For example, set can0 "birate rate” to 1000000 “dbitrate rate” to 2000000 “fd” to on
<pre># #---- For can0 ----# #
# ip link set can0 down
# ip link set can0 type can bitrate 1000000 dbitrate 2000000 fd on
# ip link set can0 up
</pre>

=== '''Send and Reveive Data''' ===

*'''As receiver'''
<pre># #---- As receiver ----# #
# ip link set can0 down
# ip link set can0 type can bitrate 1000000 dbitrate 2000000 fd on
# ip link set can0 up
# candump can0 &
</pre>

*'''As sender'''
<pre># #---- As sender ----# #
# ip link set can1 down
# ip link set can1 type can bitrate 1000000 dbitrate 2000000 fd on
# ip link set can1 up
# cansend can1 123##155

# #----If no error, the receiver will receive the following data----# #
Can0 123 [01] 55
</pre>

See more details of the usage of “candump” and “cansend” :
<pre># candump --help
# cansend --help</pre>

[[File:AFE-R761 CAN RM01.png]]

[[File:AFE-R761 CAN RM02.png]]

@@ Line 36: / Line 36: @@
 === '''Debug Port&nbsp;Connection：''' ===
-. Connect the debug port cable (1700035538-01) to the Debug port on ASRA501.
+. Connect the debug port cable (1700035538-01) to the Debug port on AFE�R761.
 . Connect it to your PC using the USB to RS-232 Cable.
@@ Line 42: / Line 42: @@
 === '''Debug Port Settings：''' ===
-AFE-R761 can communicate with a host server using serial cables. Common serial&nbsp;communication programs such as HyperTerminal, Tera Term, or PuTTY can be used&nbsp;in these applications. The example below describes the serial terminal setup using<br/> HyperTerminal on a Windows host:<br/> 1. Connect AFE-R761 with your PC using a serial cable.<br/> 2. Open HyperTerminal on your Windows PC, and select the settings demon�strated in the photo below.
+AFE-R761 can communicate with a host server using serial cables. Common serial&nbsp;communication programs such as HyperTerminal, Tera Term, or PuTTY can be used&nbsp;in these applications. The example below describes the serial terminal setup using<br/> HyperTerminal on a Windows host:<br/> 1. Connect AFE-R761 with your PC using a serial cable.
 . Insert power adapter to DC jack and power up the board. The Debug console log will be displayed on the terminal screen.
@@ Line 74: / Line 74: @@
 </pre>
-=== '''Configure''' ===
+==== '''Configure''' ====
 Use “ip” command to configure can port. See details of the usage of “ip link”:
@@ Line 125: / Line 125: @@
 # cansend --help</pre>
-[[File:AFE-R761 CAN RM01.png]]
+[[File:AFE-R761 CAN RM01.png|RTENOTITLE]]
-[[File:AFE-R761 CAN RM02.png]]
+[[File:AFE-R761 CAN RM02.png|RTENOTITLE]]