ASR-A501 Ethernet & LED - Revision history

Xingxing.li at 03:32, 21 May 2025

2025-05-21T03:32:58Z

Xingxing.li at 03:31, 21 May 2025

2025-05-21T03:31:28Z

Xingxing.li: /* Ethernet Test */

2025-05-21T03:29:02Z

‎Ethernet Test

Xingxing.li at 01:20, 21 May 2025

2025-05-21T01:20:39Z

Xingxing.li: /* Configure to Static IP */

2025-05-21T01:13:51Z

‎Configure to Static IP

Xingxing.li: Created page with " === '''Ethernet''' === ASR-A501 supports four Ethernet ports: eth0, eth1, eth2, eth3.All ports are using the “DHCP” mode by default. The following configurations and tes..."

2025-05-20T09:24:47Z

Created page with " === '''Ethernet''' === ASR-A501 supports four Ethernet ports: eth0, eth1, eth2, eth3.All ports are using the “DHCP” mode by default. The following configurations and tes..."

New page

=== '''Ethernet''' ===

ASR-A501 supports four Ethernet ports: eth0, eth1, eth2, eth3.All ports are using the “DHCP” mode by default. The following configurations and tests are taking eth0 as an example.

{| border="1" cellpadding="1" cellspacing="1" style="width: 500px;"
|-
| Ethernet
| Chipset & Speed
|
2 x RTL8211FS 10/100/1000Mbps

1 x RTL8119I  10/100/1000Mbps

1 x Intel I226  2.5Gbps

|}

==== '''Configure to Static IP''' ====

 

 

@@ Line 36: / Line 36: @@
 [[File:ROM-6881 Ethernet IPV4.png|500x300px|ROM-6881 Ethernet IPV4.png]]
 ==== '''Ethernet Test''' ====
@@ Line 53: / Line 52: @@
 # ping -I eth3 www.advantech.com
 </pre>
 === '''LED&nbsp;''' ===

← Older revision		Revision as of 03:31, 21 May 2025
Line 54:		Line 54:
	</pre>		</pre>

−	~~=== '''LED Test''' ===~~

−		+	=== '''LED ''' ===
		+	<pre># ethtool -s eth3 duplex full autoneg on speed 10       #灭
		+	# ethtool -s eth3 duplex full autoneg on speed 100      #灭
		+	# ethtool -s eth3 duplex full autoneg on speed 1000    #橙色
		+	# ethtool -s eth3 duplex full autoneg on speed 2500 #绿色(一般速度为1G需要确认网线)
		+	</pre>

@@ Line 36: / Line 36: @@
 [[File:ROM-6881 Ethernet IPV4.png|500x300px|ROM-6881 Ethernet IPV4.png]]
 ==== '''Ethernet Test''' ====
@@ Line 52: / Line 53: @@
 # ping -I eth3 www.advantech.com
 </pre>

@@ Line 16: / Line 16: @@
 |}
 ==== '''Configure to Static IP''' ====
@@ Line 28: / Line 27: @@
 [[File:ROM-6881 Ethernet wired connection.png|500x300px|ROM-6881 Ethernet wired connection.png]]
-== Configure to DHCP ==
+==== '''Configure to DHCP''' ====
 .&nbsp;Click “Applications” -> “Settings -> “Advanced Network Configration”.
@@ Line 38: / Line 37: @@
 [[File:ROM-6881 Ethernet IPV4.png|500x300px|ROM-6881 Ethernet IPV4.png]]
-== Ethernet Test ==
+==== '''Ethernet Test''' ====
-After connection, Ethernet will create a net point “eth0” and “eth1”.
+After connection, Ethernet will create a net point “eth0”,"eth1","eth2" and “eth3”.
 <pre># #---- Test eth0 ----# #
 # ping –I eth0 www.advantech.com
 # #---- Test eth1 ----# #
 # ping –I eth1 www.advantech.com
 </pre>

@@ Line 16: / Line 16: @@
 |}
 ==== '''Configure to Static IP''' ====
-&nbsp;
+. Click “Applications” -> “Settings” -> “Advanced Network Configration”.
-&nbsp;
+After connection, Ethernet will create a net point “eth0” and “eth1”.