How to debug - Revision history

Xingxing.li at 02:28, 26 October 2021

2021-10-26T02:28:28Z

Xingxing.li at 02:14, 22 October 2021

2021-10-22T02:14:45Z

Xingxing.li at 02:13, 22 October 2021

2021-10-22T02:13:07Z

Xingxing.li at 02:11, 22 October 2021

2021-10-22T02:11:29Z

Xingxing.li at 02:10, 22 October 2021

2021-10-22T02:10:32Z

Yunjin.jiang at 09:07, 25 March 2019

2019-03-25T09:07:12Z

Yunjin.jiang at 08:37, 25 March 2019

2019-03-25T08:37:00Z

Yunjin.jiang at 08:20, 25 March 2019

2019-03-25T08:20:37Z

Yunjin.jiang at 08:03, 25 March 2019

2019-03-25T08:03:29Z

Yunjin.jiang at 07:56, 25 March 2019

2019-03-25T07:56:15Z

@@ Line 11: / Line 11: @@
 RSB4680 debug port pin define&nbsp;:&nbsp;
-{| border="1" cellspacing="1" cellpadding="1" style="width: 229px;"
+{| border="1" cellspacing="1" cellpadding="1"
 |-
-| style="width: 109px;" | '''PIN'''
+| '''PIN'''
-| style="width: 107px;" | '''PIN Name'''
+| '''PIN Name'''
 |-
-| style="width: 109px;" | 1
+| 1
-| style="width: 107px;" | NC
+| NC
 |-
-| style="width: 109px;" | 2
+| 2
-| style="width: 107px;" | TX
+| TX
 |-
-| style="width: 109px;" | 3
+| 3
-| style="width: 107px;" | RX
+| RX
 |-
-| style="width: 109px;" | 4
+| 4
-| style="width: 107px;" | GND
+| GND
 |}
 [[File:RSB4680 Debug port.jpg|885x675px|RSB4680 Debug port.jpg]]
-<span style="color:#FF0000;">'''Note&nbsp;:&nbsp;'''</span>
+'''Note&nbsp;:&nbsp;'''
 Please connect device's TX to usb2uart adapter's RX and&nbsp;device's RX to usb2uart adapter's TX .
@@ Line 99: / Line 99: @@
 set send pack 1000
 set window 5
 </pre>
-<span style="color:#FF0000;">'''Note&nbsp;:&nbsp;'''</span>
+'''Note&nbsp;:&nbsp;'''
 Change "/dev/ttyUSB0" according your system, Use Command "ls /dev/ttyUSB*" .

@@ Line 99: / Line 99: @@
 set send pack 1000
 set window 5
 </pre>
@@ Line 109: / Line 108: @@
 <pre>sudo kermit
 </pre>
 = MiniCom =

← Older revision		Revision as of 02:13, 22 October 2021
Line 34:		Line 34:

	Please connect device's TX to usb2uart adapter's RX and device's RX to usb2uart adapter's TX .		Please connect device's TX to usb2uart adapter's RX and device's RX to usb2uart adapter's TX .
−
−
−
−
−
−

	= UART parameter =		= UART parameter =

@@ Line 6: / Line 6: @@
 *[http://www.prolific.com.tw/US/ShowProduct.aspx?pcid=41 PL2303]
 *[https://sparks.gogo.co.nz/ch340.html CH340]
 = Hardware PIN define <!--5f39ae17-8c62-4a45-bc43-b32064c9388a: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--> =

@@ Line 77: / Line 77: @@
 "Kermit" and "MiniCom" are very famous tools on Ubuntu.
-&nbsp;Connect adapter to PC , find COM port :
+&nbsp;Connect adapter to PC , find COM port&nbsp;:
 <pre>$ ls /dev/ttyUSB*
 /dev/ttyUSB0
@@ Line 112: / Line 112: @@
 </pre>
-<span style="color:#FF0000;">'''Note :&nbsp;'''</span>
+<span style="color:#FF0000;">'''Note&nbsp;:&nbsp;'''</span>
 Change "/dev/ttyUSB0" according your system, Use Command "ls /dev/ttyUSB*" .
@@ Line 172: / Line 172: @@
             +--------------------------+</pre>
 Press "↓"， move cursor to "Serial port setup" to Config parameter.
-Then press "A"-"G" to set relative content as following :
+Then press "A"-"G" to set relative content as following&nbsp;:
 <pre> +-----------------------------------------------------------------------+
-    | A -    Serial Device      : /dev/ttyUSB0                              |
+    | A -    Serial Device     &nbsp;: /dev/ttyUSB0                              |
-    | B - Lockfile Location     : /var/lock                                 |
+    | B - Lockfile Location    &nbsp;: /var/lock                                 |
-    | C -   Callin Program      :                                           |
+    | C -   Callin Program     &nbsp;:                                           |
-    | D -  Callout Program      :                                           |
+    | D -  Callout Program     &nbsp;:                                           |
-    | E -    Bps/Par/Bits       : 115200 8N1                                |
+    | E -    Bps/Par/Bits      &nbsp;: 115200 8N1                                |
-    | F - Hardware Flow Control : No                                        |
+    | F - Hardware Flow Control&nbsp;: No                                        |
-    | G - Software Flow Control : No                                        |
+    | G - Software Flow Control&nbsp;: No                                        |
     |                                                                       |
     |    Change which setting?                                              |

@@ Line 76: / Line 76: @@
 "Kermit" and "MiniCom" are very famous tools on Ubuntu.
@@ Line 81: / Line 88: @@
 == Kermit ==
-'''Install Kermit :&nbsp;'''
+'''Install Kermit&nbsp;:&nbsp;'''
 <pre>sudo apt-get update
 sudo apt-get install ckermit
 </pre>
-'''Config Kermit :&nbsp;'''
+'''Config Kermit&nbsp;:&nbsp;'''
-<pre>vi $HOME/.kermrc&nbsp;
+<pre>vi $HOME/.kermrc;
 </pre>
 </pre>

@@ Line 61: / Line 61: @@
 [[File:RK3288 Debian Debug Port Number.png|800x572px|RK3288 Debian Debug Port Number.png]]
-Putty is very populate tool. [https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html Download putty here.]
+Putty is very populate tool on Windows. [https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html Download putty here.]
 Run PUTTY.exe, select&nbsp;Connection type of "Serial" , input COM port found in Device Manager.
@@ Line 70: / Line 70: @@
 Then Click "Open" to start debug console.

@@ Line 6: / Line 6: @@
 *[http://www.prolific.com.tw/US/ShowProduct.aspx?pcid=41 PL2303]
 *[https://sparks.gogo.co.nz/ch340.html CH340]
@@ Line 36: / Line 38: @@
 Please connect device's TX to usb2uart adapter's RX and&nbsp;device's RX to usb2uart adapter's TX .
@@ Line 48: / Line 52: @@
 *Parity&nbsp; &nbsp; &nbsp; ：None
 *FlowControl：None or XON/XOFF
 [[File:RK3288 Debian Debug Port Config.png|RTENOTITLE]]

@@ Line 3: / Line 3: @@
 There are plenty types of usb to uart bridge in the market . Most of them use the following chip&nbsp;:
-*CP210X
+*[https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers CP210X]
-*PL2303
+*[http://www.prolific.com.tw/US/ShowProduct.aspx?pcid=41 PL2303]
+*[https://sparks.gogo.co.nz/ch340.html CH340]

← Older revision		Revision as of 07:56, 25 March 2019
Line 37:		Line 37:

	Please connect device's TX to usb2uart adapter's RX and device's RX to usb2uart adapter's TX .		Please connect device's TX to usb2uart adapter's RX and device's RX to usb2uart adapter's TX .
		+
		+
		+
		+

	= UART parameter =		= UART parameter =