IoTGateway/BSP/Linux/AM335x/V2/System Service and Usage - Revision history

Chang.qing at 02:21, 8 February 2017

2017-02-08T02:21:12Z

2017-02-08T02:18:06Z

2017-02-08T02:17:41Z

2017-02-08T02:15:18Z

2017-02-08T02:10:52Z

2017-02-08T02:09:30Z

2017-02-08T01:54:35Z

2017-02-08T01:51:57Z

2017-02-08T01:50:46Z

2017-02-08T01:48:48Z

@@ Line 128: / Line 128: @@
 USB connector of RSB4220 supports two modes: Host and Slave, which require software and hardware support.The system is set to Host mode by default. If you do not need to switch between the two modes, no operation is required; if you need to switch, please refer to the following steps:
-. Please refer to the figure below to select otg mode
+. Please refer to the below figure to select otg mode
 [[File:Rsb-4220-otg.png|RTENOTITLE]]

@@ Line 118: / Line 118: @@
 Wifi control related commands have been included, so you can execute the below commands to connect wifi when the module is powered on.
 <pre>advantech# wifi-wpaon WIFI_SSID WIFI_PASSWORD</pre>
 <font color="#FF0000">Note: This command is used to connect to the account whose wifi name is WIFI_SSID using WIFI_PASSWORD.</font>
 <pre>advantech# wifi-off</pre>
 <font color="#FF0000">Note: This command is used to turn off wifi function.</font>

@@ Line 119: / Line 119: @@
 <pre>advantech# wifi-wpaon WIFI_SSID WIFI_PASSWORD</pre>
 This command is used to connect to the account whose wifi name is WIFI_SSID using WIFI_PASSWORD.
 <pre>advantech# wifi-off</pre>
 This command is used to turn off wifi function.
 == <span style="color:#0070c0">Otg Mode Selection</span> ==

@@ Line 130: / Line 130: @@
 . Please refer to the figure below to select otg mode
-[[File:Rsb-4220-otg.png]]
+[[File:Rsb-4220-otg.png|RTENOTITLE]]
 . Execute one of the following commands to switch to the corresponding mode after the terminal is powered on.
@@ Line 139: / Line 139: @@
 <pre>root@am335x-adv:/ # echo “peripheral” > /etc/otg-mode
 </pre>
 . Reboot the system.

@@ Line 124: / Line 124: @@
 This command is used to turn off wifi function.
-== <span style="color:#0070c0">Otg Mode Selection</span><span style="color:#0070c0"></span> ==
+== <span style="color:#0070c0">Otg Mode Selection</span> ==
 USB connector of RSB4220 supports two modes: Host and Slave, which require software and hardware support.The system is set to Host mode by default. If you do not need to switch between the two modes, no operation is required; if you need to switch, please refer to the following steps:
 . Please refer to the figure below to select otg mode
 . Execute one of the following commands to switch to the corresponding mode after the terminal is powered on.

← Older revision		Revision as of 01:54, 8 February 2017
Line 123:		Line 123:

	This command is used to turn off wifi function.		This command is used to turn off wifi function.
		+
		+	== <span style="color:#0070c0">Otg Mode Switch</span><span id="result_box" class="short_text" lang="en"><span></span></span> ==
		+
		+	RSB-4221 supports Marverll SD8897 wifi/bt modules throught M.2. To use Marverll SD8897 wifi/bt modules, you have to boot the linux system from emmc and do following setting under uboot:
		+	<pre>AM335X RSB-4221 U-Boot# setenv mmcargs setenv bootargs console=${console} ${optargs} root=${mmcroot} rootfstype=${mmcrootfstype} M2WIFIFlag=TRUE
		+	AM335X RSB-4221 U-Boot# saveenv
		+	</pre>

@@ Line 114: / Line 114: @@
 </pre>
-Wifi command introduction
+=== Wifi command introduction ===
 Wifi control related commands have been included, so you can execute the below commands to connect wifi when the module is powered on.

@@ Line 100: / Line 100: @@
 = Other special function =
-== Wifi Configuration and Usage ==
+== <span style="color:#0070c0">Wifi Configuration and Usage</span> ==
-=== Wifi module introduction<span id="result_box" class="short_text" lang="en"><span></span></span> ===
+=== Wifi module introduction ===
 RSB-4221 supports Marverll SD8897 wifi/bt modules throught M.2. To use Marverll SD8897 wifi/bt modules, you have to boot the linux system from emmc and do following setting under uboot:
@@ Line 114: / Line 114: @@
 </pre>
-Wifi command <span id="result_box" class="short_text" lang="en"><span></span></span>introduction
+Wifi command introduction
 Wifi control related commands have been included, so you can execute the below commands to connect wifi when the module is powered on.