Xingxing.li: Created page with " == '''產品介紹(Product introduction )''' == === '''產品特性(Product Features)''' === Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz Onboard LPDDR4 2GB *HDMI 1..."

2024-03-29T06:50:01Z

Created page with " == '''產品介紹(Product introduction )''' == === '''產品特性(Product Features)''' === *Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz *Onboard LPDDR4 2GB *HDMI 1..."

New page

== '''產品介紹(Product introduction )''' ==

=== '''產品特性(Product Features)''' ===

*Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz
*Onboard LPDDR4 2GB
*HDMI 1920x1080 at 60Hz, 1 Dual Channel 24 bit LVDS
*1 2-wire RS-232, 1 USB3.0, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
*1 mini-PCIe for 3G/4G
*UIO expansion 3 USB2.0, 8 GPIO, 2 RS232 2/2-wires UART, 1 I2C
*Supports Debian9/10 and Android7.1/10.0
*Support I/O Expansions by UIO40-Express I/O boards, please refer to page #3 for more information

=== '''產品官網連結(Product Features) ''' ===

[https://www.advantech.com/en/search/?q=RSB-3710&st=support&from=support '''RSB-3710''']

== '''硬件接口說明(Hardware interface introduction)''' ==

=== '''接口布局和尺寸(Layout and Sizes)''' ===

=== '''接口布局圖 Board Dimension Layout ''' ===

[[File:RSB-3710 product pic11 2021-11-02 100745.jpg|RTENOTITLE]]

 

[[File:RSB-3710 product pic22 2021-11-02 100837.jpg|RTENOTITLE]]

 

[[File:RSB-3710 product pic33 2021-11-02 100904.jpg|RTENOTITLE]]

== ''' Connector List''' ==

'''[[File:RSB-3710 Jumper and Connector Locations 2021-11-02 101526.jpg|RTENOTITLE]]'''

{| border="1" cellpadding="1" cellspacing="1"
|-
| BAT
| RTC Battery Connector
|-
| HDMI
| HDMI1 CONN
|-
| BL
| LVDS BKL CONN
|-
| LVDS
| LVDS CONN
|-
| LAN1
| LAN
|-
| LAN2
| LAN
|-
| MINIPCIE
| MINI PCIE 52P 
|-
| SIM
| Nano SIM Card
|-
| AUDIO
| Audio PIN Header
|-
| USB1
| USB CONN
|-
| COM2/Debug 
| COM2 
|-
| SD
| SD Slot
|-
| OTG
| USB
|-
| BTN
| Power BTN pin header 
|-
| RST
| Reset Button
|-
| DCIN1 
| 12V DC Jack
|-
| LED
| LED
|-
| CN11
| UIO1
|-
| CN12
| UIO2
|}

 

=== '''接口引脚定義 (Pin definitions)''' ===

*[[BAT|BAT]]
*[[HDMI1|HDMI1]]
*[[BL|BL]]
*[[LVDS|LVDS]]
*[[LAN1,_LAN2|LAN1, LAN2]]
*[[MINIPCIE|MINIPCIE]]
*[[SIM|SIM]]
*[[Audio|Audio]]
*[[USB1|USB1]]
*[[COM2/Debug|COM2/Debug]]
*[[SD|SD]]
*[[OTG|OTG]]
*[[BTN|BTN]]
*[[RST|RST]]
*[[DCIN1|DCIN1]]
*[[LED|LED]]
*[[CN11|CN11]]
*[[CN12|CN12]]
*[[RSB-3710_Jumper_List|RSB-3710_Jumper List]]

=== '''机械尺寸  ('''Mechanical Characteristics) ===

[[File:RSB-3710 Mechanical 2021-11-02 102727.jpg|RTENOTITLE]]

== '''快速入门 (Quick Start)''' ==

=== '''系统下载 ( OS Download)''' ===

'''Android10'''

Note：  LIV=Yocto Linux, UIV=Ubuntu, DIV=Debian, AIV=Android

             LBV=BSP, LIV=Image

{| border="1" cellpadding="1" cellspacing="1"
|-
| '''Platform'''
| '''Product'''
| '''Image Version'''
| '''Release Date'''
| '''Release Version'''
| '''Release notes'''
| '''Image Download'''
| '''BSP Download Tag'''
| '''Comment'''
|-
| RK3399
| RSB-3710
| AIV1005
| 2021/12/15
| Alpha
| NA
|
[https://pan.baidu.com/s/1ck7M6SqRarYQh_ud3GxalA Baidu]  Password：a887

[https://www.dropbox.com/sh/zcwyjknty83iklh/AAAsbYBy44GhQREpHfv0qFLta?dl=0 Dropbox]

| RK3399_Q10_AIV1005.xml
|  
|}

*Alpha:  Basic I/O function bring up by RD;

*Beta:  Basic I/O function、performance and middleware verified by RD. Peripherals integrated;

*GA:  Beta version by QE verification;

*RTM:  Beta version by SI/Power/QE verification and pre-loaded;

== '''Android 燒錄方法 (Flash Android image into eMMC Method) ''' ==

'''1. Prepare a mirco USB Cable and Debug Cable '''

''' mirco USB''' 

 

 

 

 

[[File:RSB-3710 mirco usb 2021-11-02 143011.jpg|RTENOTITLE]]

'''Debug Cable '''

[[File:RSB-3710 debug cable 2021-11-02 144650.jpg|RTENOTITLE]]

2. Plug the OTG Cable into RSB-3720 

[[File:RSB-3710 OTG USBcable 2021-11-02 143356.jpg|RTENOTITLE]]

Connect Debug cable 

[[File:RSB-3710 debug and debug port 1 2021-11-02 145203.jpg|RTENOTITLE]]

'''2. 設定終端機(Set Debug Terminal) '''

Debug 串口調試 (Debug port Setting)

 Tera Term setting 
<pre> Baud Rate：115200
Data ：8
Parity ：none
Stop ：1
Flow Control：none</pre>

: 

Tera Term Tool 

[[File:TeraTerm 2021-09-10 140930n.jpg|RTENOTITLE]]

[[File:TeraTerm12021-09-10 141114n.jpg|RTENOTITLE]]

Note:

Check the Sriel port in Device Manager ：

if you can not identify the Serial device , please check your serial driver. 

 

3.Open the flash tool 

 [[File:RSB-3710 android tool 2021-11-02 150159.jpg|RTENOTITLE]]

4. Turn on the power 

5. When you see the debug message in Terminal , then press "Ctrl+C" , then log into Uboot stage 

[[File:RSB-3710 CtrlC uboot 2021-11-02 150842.jpg|RTENOTITLE]]

6. In Uboot , please type  '''"loader"  , then the device will transfer to "Flash mode" ''' , Android tool also will show  '''"Found One MASKROM Device " '''

  [[File:RSB-3710 android loader 2022-01-20 154115.jpg|RTENOTITLE]]

 

 

7. In RKDevTool pressed  "Run"  , and it will flash image into eMMC.

[[File:RSB-3710 Run RKDevTool 2021-11-02 160456.jpg|RTENOTITLE]]

8. The flash process  was finishded 

  [[File:RSB-3710 finish RKDevTool 2021-11-02 160931.jpg|RTENOTITLE]]

9. Reboot the device , and connect with HDMI , it will show the Android Desktop. 

[[File:RSB-3710 Android desktop pic.png|RTENOTITLE]]

== '''Debian 燒錄方法 ( Flash Debian image into eMMC Method) ''' ==

'''1. Prepare a  mirco USB cable and Debug Cable '''

''' mirco USB''' 

 

 

 

 

[[File:RSB-3710 mirco usb 2021-11-02 143011.jpg|RTENOTITLE]]

'''Debug Cable '''

[[File:RSB-3710 debug cable 2021-11-02 144650.jpg|RTENOTITLE]]

2. plug'''  '''mirco USB cable into the  RSB-3710 OTG port. 

[[File:RSB-3710 OTG USBcable 2021-11-02 143356.jpg|RTENOTITLE]]

Connect  Debug cable 

[[File:RSB-3710 debug and debug port 1 2021-11-02 145203.jpg|RTENOTITLE]]

'''3. 設定終端機(Set Debug Terminal) '''

Debug 串口調試 (Debug port Setting)

 
<pre> Baud Rate：115200
Data ：8
Parity ：none
Stop ：1
Flow Control:none</pre>

: 

Tera Term Tool 

[[File:TeraTerm 2021-09-10 140930n.jpg|RTENOTITLE]]

[[File:TeraTerm12021-09-10 141114n.jpg|RTENOTITLE]]

Note:

查看PC端的串口号(Check the Sriel port in Device Manager) :

如果沒有找到請先確認是否有安裝驅動(if you can not identify the Serial device , please check your serial driver.) 

 

3. Execute the Flash tool 

 [[File:RSB-3710 RKDevTool Debian 2021-11-02 171049.jpg|RTENOTITLE]]

4. Turn on the power. 

5. Press "'''Ctrl + C", '''log into u-boot 

[[File:RSB-3710 CtrlC uboot 2021-11-02 150842.jpg|RTENOTITLE]]

6. In Uboot , please type '''"rbrom " ''' , the device will transfer to'''"Flash mode"''' , Android tool also will show '''"Found One MASKROM Device " '''

[[File:RSB-3710 rbrom 2021-11-02 151430.jpg|RTENOTITLE]]

 7. In RKDevTool , Press '''"Run"''' , it will flash the image into eMMC. 

[[File:RSB-3710 Run RKDevTool 2021-11-02 160456.jpg|RTENOTITLE]]

8.  The flash process  was finishded 

  [[File:RSB-3710 finish RKDevTool 2021-11-02 160931.jpg|RTENOTITLE]]

9. Reboot the device , and connect with HDMI , it will show the Debian Desktop. 

 

'''    [[File:RSB-3710 Debian Screenshot from 2022-01-20 06-54-41.png|RTENOTITLE]]'''

== '''系统的基本使用(Linux System Basic Operating Method)''' ==

=== [[Display_Setting_(RSB-3710)|'''Display Setting (RSB-3710)''']] ===

{| border="1" cellpadding="1" cellspacing="1"
|-
| lvds
| lvds-g070vw01; lvds-g150xgel05; lvds-g215hvn01
|-
| hdmi
| hdmi-default
|-
| dp
| dp-default
|}

{| border="1" cellpadding="1" cellspacing="1"
|-
| '''IN uboot'''
| '''In Debian/Android'''
|-
| setenv prmry_screen hdmi-default
| fw_setenv prmry_screen hdmi-default
|-
| setenv extend_screen edp-1920x1080
| fw_setenv extend_screen edp-1920x1080
|-
| saveenv
|  
|-
| reset
| reboot
|}

In u-boot:

=> setenv prmry_screen lvds-g070vw01

=> setenv extend_screen hdmi-default

=> saveenv

=> reset

In Linux:

~# fw_setenv prmry_screen lvds-g070vw01

~# reboot

Modify LVDS backlight PWM: (Defaul is 20KHz, New version BSP support to modify the PWM clock in u-boot from 200~20KHz)

In u-boot:

=> setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)

In Linux:

~# fw_setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)

~# reboot

 

Check PWM duty sysle in Linux:

~# cat /sys/kernel/debug/pwm

[[File:Z75.jpg|RTENOTITLE]]

=== '''乙太網路使用方法(Ethernent Testing Method)''' ===

'''Command : ifconfig '''

'''Command: Ping 8.8.8.8 '''

=== '''WiFi使用方法(WIFI Testing Method)''' ===
<pre># killall wpa_supplicant
# ifconfig wlan0 up
# wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf
# cat /tmp/wpa.conf
# wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
# udhcpc -b -i wlan0
# ifconfig
# ping 8.8.8.8
Add DNS to /etc/resolv.conf
# cat /etc/resolv.conf
# Generated by Connection Manager
nameserver 8.8.8.8
nameserver 8.8.4.4
Now can ping google.com
# ping google.com</pre>

=== '''4G使用方法(4G Testing Method)''' ===

[[Ubuntu_-_4G_模塊(EC-25J)_設定_(_4G_module_(EC-25J)_in_Ubuntu_system)|Ubuntu - 4G 模塊(EC-25J) 設定 ( 4G module (EC-25J) in Ubuntu system) ]]

[[Ubuntu_-_4G_模塊(EC-20)_設定(_4G_module_(EC-20)_in_Ubuntu_system)|Ubuntu - 4G 模塊(EC-20) 設定( 4G module (EC-20) in Ubuntu system) ]]

=== '''GPIO使用方法(GPIO Operating Method)''' ===

'''[[File:RSB-3710 GPIO define 2022-01-20 142613.jpg|RTENOTITLE]]'''

[[File:RSB-3710 gpio1 2022-01-20 142757.jpg|RTENOTITLE]]

[[File:RSB-3710 gpio2 2022-01-20 142824.jpg|RTENOTITLE]]

=== '''蓝牙使用方法(BlueTooth Operating Method)''' ===
<pre># hciattach /dev/ttymxc0 bcm43xx 115200 flow
# hciconfig hci0 up
# hcitool scan# bluetoothctl
# discoverable on
#pairable on
# scan on
# scan off
# pair 84:C5:A6:D3:AF:E4
# connect 84:C5:A6:D3:AF:E4
Check BT connect info
# info 84:C5:A6:D3:AF:E4</pre>

=== '''音訊使用方法(BlueTooth Operating Method)''' ===
<pre>Line-in , Line-out, MIC
1.Line-out
Command : gplay-1.0
2.MIC
Command : arecord
Check audio codec:

# cat /proc/asound/cards
0 [sgtl5000 ]: sgtl5000 - sgtl5000
sgtl5000
1 [audiohdmi ]: audio-hdmi - audio-hdmi
audio-hdmi
root@imx8mprsb3720a1:~#
Set Mic/audio volume
# amixer set Mic 100%
# amixer set Lineout 100%
# amixer set PCM 100%

Record and playback
Example command:
# arecord –t wav –c 1 –r 44100 –d 5 /tmp/mic.wav
# aplay /tmp/mic.wav

Record from MIC:
# arecord -D plughw:0,0 -r 16000 -f S16_LE ./f-16000.wav
Recording WAVE './f-16000.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono
# aplay f-16000.wav
Playing WAVE 'f-16000.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono

Play wav file from codec:
# aplay -D plughw:0,0 file_example_WAV_10MG.wav
Playing WAVE 'file_example_WAV_10MG.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

Play wav file from HDMI:
# aplay -D plughw:1,0 file_exam
ple_WAV_10MG.wav
Playing WAVE 'file_example_WAV_10MG.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
</pre>

=== '''看門狗測試 (Watch Dog Test method) ''' ===
<pre>System will reboot after 1 sec
# /unit_tests/Watchdog/wdt_driver_test.out 1 2 0
</pre>

 

=== '''遠程訪問及文件傳輸(Remote Access and File Transimmion)''' ===

'''              查看主板IP位址 ( Chech IP Address )：'''
<pre> Command : ifconfig</pre>

[[File:RSB-3710 ifconfig 2022-01-20 140604.jpg|RTENOTITLE]]

==== Windows下SSH访问及文件传输 ====

SSH Remote Log into Device 

*SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
*需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码

 

[[File:SSHsettingdetail.png|RTENOTITLE]]

[[File:SSHSetting2021-09-10 143631.jpg|RTENOTITLE]]

 

[[File:Sshsetting12021-09-10 143743n.jpg|RTENOTITLE]]

== '''通用方法(General Method)''' ==

=== '''查看CPU温度(Check CPU Temperature)''' ===
<pre> root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 40000

# 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 40°</pre>

=== '''查看CPU频率(Check CPU Frequency)''' ===
<pre> cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
>> 1200000
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
>> 1800000</pre>

=== '''查看内存容量(Check Memory Capacity)''' ===
<pre>root@linaro-alip:~# busybox free -m
              total        used        free      shared  buff/cache   available
Mem:           1961         303        1096          97         561        1575
Swap:             0           0           0
root@linaro-alip:~#
</pre>

=== '''查看存储容量(Check Storage Capacity)''' ===
<pre>root@linaro-alip:~# busybox df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 7.8G      2.8G      4.6G  37% /
devtmpfs                972.3M      8.0K    972.3M   0% /dev
tmpfs                   980.8M         0    980.8M   0% /dev/shm
tmpfs                   980.8M     16.8M    964.0M   2% /run
tmpfs                     5.0M      4.0K      5.0M   0% /run/lock
tmpfs                   980.8M         0    980.8M   0% /sys/fs/cgroup
/dev/mmcblk1p10           6.4G      3.8M      6.4G   0% /userdata
/dev/mmcblk1p7           62.6M     12.0M     47.3M  20% /oem
tmpfs                   196.2M         0    196.2M   0% /run/user/0
tmpfs                   196.2M      8.0K    196.1M   0% /run/user/1000
root@linaro-alip:~#</pre>

=== '''網路Ping測試(Ping Network Testing)''' ===
<pre> ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre>

=== '''設置RTC (RTC Setting) ''' ===

Set system time to current, then write to RTC    root@linaro-alip:~# date 01282022    Fri Jan 28 20:22:00 UTC 2022    root@linaro-alip:~# Restart the RTC time to system time # hwclock -s && date

root@linaro-alip:~# hwclock -s && date Thu Jan 20 06:18:26 UTC 2022 root@linaro-alip:~# 

== '''Android BSP編譯方法(Android BSP Compile Method)''' ==

[http://ess-wiki.advantech.com.tw/view/Debian_BSP_User_Guide_for_rk3399_risc_series&nbsp http://ess-wiki.advantech.com.tw/view/Debian_BSP_User_Guide_for_rk3399_risc_series&nbsp];

=== '''如果有驗證上的錯誤請使用以下的方法(If you got " Server certificate verification failed " message ,please follow the solution as below) ''' ===

'''### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none ============================================================ export GIT_SSL_NO_VERIFY=1 #or git config --global http.sslverify false ============================================================'''

RSB-3710 user guide Android10 - Revision history

Xingxing.li: Created page with " == '''產品介紹(Product introduction )''' == === '''產品特性(Product Features)''' === *Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz *Onboard LPDDR4 2GB *HDMI 1..."

Xingxing.li: Created page with " == '''產品介紹(Product introduction )''' == === '''產品特性(Product Features)''' === Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz Onboard LPDDR4 2GB *HDMI 1..."