Revision as of 03:30, 17 February 2020

Introduction

Modbus enables communication among many devices connected to the same network, for example, a system that measures temperature and humidity and communicates the results to a computer. Modbus is often used to connect a supervisory computer with a remote terminal unit (RTU) in supervisory control and data acquisition (SCADA) systems.

Many of the data types are named from its use in driving relays: a single-bit physical output is called a coil, and a single-bit physical input is called a discrete input or a contact.

Modbus Service is a Windows/Linux system service for WISE Agent to read sensor data from Modbus device or write data into Modbus device. After sensor data are acquired, WISE Agent will upload the data to the WISE-PaaS Cloud.

Features

EdgeSense Modbus-Master aims to collect data from Modbus Slave.

Feature:

• Support connection with multiple Modbus slave.
• Support access both Modbus TCP and RTU in one service.
• Support individual read interval by connection.
• Configurable sensor alias.
• Support byte swap.
• Currently support up-link Modbus Coil, Descrete input, Input register & Holding register data to WISE-PaaS , not support down-link from WISE-PaaS.

How to

Software Requirements

• MQTT broker

Installation

Windows:

1. Download Modbus-Master for Windows from Release Table.

2. Double click the installer to launch the installer to install it to the machine.

Debian:

1. Download OPC-UA Client for Debian from Release Table.

2. Launch the installer to install it to the machine.

sudo ./device-modbus-master-3.0.1-Debian_9.9-rk3399.run

Configuration

EdgeSense Modbus Master can manage multiple Modbus Slave setting and individual sensor's parameters, below settings are default after Modbus Master installation.

1. Device Configuration: <Install_folder>\config\industry\device-industry.yaml

metadata: 
  name: "Modbus devices"
  labels: ["Modbus"] 
  Description: "Modbus TCP/RTU devices with 3 sensors in holding register area 40001~40003"
  UpdateData: 2020-01-08-14:25:30

# LinkInfo: You can add a new link with unique name
  # <LinkName>: Unique Link Name
    # Params: Serial Port or Network parameters
    # Info: Time interval of polling data & check link 
    # DevList: Device list which defined in DeviceInfo section

LinkInfo: 
  TCP-IP-1:
    Params: 
      Driver: Modbus-TCP
      ConnectType: Net
      IP: 127.0.0.1
      Port: 502
      Timeout: 1000          # A request timeout in milliseconds
   
    Info: 
      PollingInterval: 3000  # Polling interval in milliseconds
      Retry: 3               # Count of retry min:0 max:3
      AliveTime: 10          # Link Timeout in second: SDK will release this link if there are any request over this AliveTime ( second )
      CheckLinkInterval: 2   # Check link status interval (second)

    DevList:
      - Device-1

  COM1:
    Params:
      Driver: Modbus-RTU
      ConnectType: Serial
      PortName: COM1
      BaudRate: 9600
      DataBits: 8
      StopBits: 1
      Parity: None
      Timeout: 1000          # A request timeout in milliseconds
    
    Info: 
      PollingInterval: 3000  # Polling interval in milliseconds 
      Retry: 3               # Count of retry min:0 max:3
      AliveTime: 10           # Link Timeout in second: SDK will release this link if there are any request over this AliveTime ( second )
      CheckLinkInterval: 2   # Check link status interval (second)

    DevList: 
      - Device-2


# DeviceInfo: You can add a new device with unique name
  # <DeviceName>: Unique Device Name
    # Params: Station number
    # Profile: Profile file name

DeviceInfo:
  Device-1:
    Params: 
      Station: 1

    Profile: MODBUS_DEVICE_01.yaml

  Device-2:
    Params:
      Station: 2

    Profile: MODBUS_DEVICE_02.yaml

2. Sensor Configuration for Device-1: <Install_folder>\config\industry\Profile\MODBUS_DEVICE_01.yaml

metadata: 
  name: MODBUS_DEVICE_01.yaml
  labels: ["MODBUS"] 
  Description: This profile is for Modbus device 01
  version: 1.0.1
  UpdateData: 2020-01-08-14:25:30

Sensor:
  Temperature:
    Params:
      Address: 0    # Address
      Length: 1  
      DataType: int16
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw       # Access Right: r, w, rw
      min: -10      # Minimum Value 
      max: 100      # Maximum Value
      u: "celsius"  # Unit

  Humidity:
    Params:
      Address: 1
      Length: 1  
      DataType: int16 
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw       # Access Right: r, w, rw
      min: 0        # Minimum Value 
      max: 100      # Maximum Value
      u: "percent"  # Unit

2. Sensor Configuration for Device-2: <Install_folder>\config\industry\Profile\MODBUS_DEVICE_02.yaml

metadata: 
  name: MODBUS_DEVICE_02.yaml
  labels: ["MODBUS"] 
  Description: This profile is for Modbus device 02
  version: 1.0.1
  UpdateData: 2020-01-08-14:25:30

Sensor:
  X-Axis:
    Params:
      Address: 0   # Address
      Length: 1  
      DataType: int16
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw      # Access Right: r, w, rw
      min: -10     # Minimum Value 
      max: 100     # Maximum Value
      u: "mm/sec"  # Unit

  Y-Axis:
    Params:
      Address: 1
      Length: 1  
      DataType: int16 
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw      # Access Right: r, w, rw
      min: -100    # Minimum Value 
      max: 100     # Maximum Value
      u: "mm/sec"  # Unit 

Demonstration

1. Open Modbus Simulator: Launch ModSim32 and click "New" in program menu to create a new simulator page.

2. Set parameter as below:

• Device Id: 1
• Address: 0001
• Length: 2
• Modbus Point Type: HOLDING REGISTER

3. Enable Auto Simulation:

• Double click on the sensor address 40001
• Click "Auto Simulation"

4. Set simulation parameters:

• Check "Enable"
• Simulation Type: Increment
• Change Interval (secs): 5
• Step VAlue: 1
• Low Limit: 10
• High Limit: 20

5. Do the same step for the address 40002 and set simulation parameter as below:

• Simulation Type: Increment
• Low Limit: 60
• High Limit: 80

6. Set Connection to Modbus/TCP Svr:

7. Edit Device Configuration for the demo: <Install_folder>\config\industry\device-industry.yaml

metadata: 
  name: "Modbus devices"
  labels: ["Modbus"] 
  Description: "Modbus TCP/RTU devices with 3 sensors in holding register area 40001~40003"
  UpdateData: 2020-01-08-14:25:30

# LinkInfo: You can add a new link with unique name
  # <LinkName>: Unique Link Name
    # Params: Serial Port or Network parameters
    # Info: Time interval of polling data & check link 
    # DevList: Device list which defined in DeviceInfo section

LinkInfo: 
  TCP-IP-1:
    Params: 
      Driver: Modbus-TCP
      ConnectType: Net
      IP: 127.0.0.1
      Port: 502
      Timeout: 1000          # A request timeout in milliseconds
   
    Info: 
      PollingInterval: 3000  # Polling interval in milliseconds
      Retry: 3               # Count of retry min:0 max:3
      AliveTime: 10          # Link Timeout in second: SDK will release this link if there are any request over this AliveTime ( second )
      CheckLinkInterval: 2   # Check link status interval (second)

    DevList:
      - Device-1

8. Edit Sensor Configuration for the demo: <Install_folder>\config\industry\Profile\MODBUS_DEVICE_01.yaml

metadata: 
  name: MODBUS_DEVICE_01.yaml
  labels: ["MODBUS"] 
  Description: This profile is for Modbus device 01
  version: 1.0.1
  UpdateData: 2020-01-08-14:25:30

Sensor:
  Temperature:
    Params:
      Address: 0    # Address
      Length: 1  
      DataType: int16
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw       # Access Right: r, w, rw
      min: -10      # Minimum Value 
      max: 100      # Maximum Value
      u: "celsius"  # Unit

  Humidity:
    Params:
      Address: 1
      Length: 1  
      DataType: int16 
      DataFormat: ABCD

    Info:
      v: -1
      asm: rw       # Access Right: r, w, rw
      min: 0        # Minimum Value 
      max: 100      # Maximum Value
      u: "percent"  # Unit

<span style="font-size:medium;">9. Restart Modbus Master services</span>

• Open Windows Task Manager
• Restart service: device-modbus-protocol
• Restart service: device-modbus-master

10. Verify sensor data at DeviceOn Monitor Sensor Data page

Release

This is an overview that displays Modbus Service versions and some stats and numbers for each release.

Above files are available at local server, please paste file's url in File Explorer to copy file. (How to access to EOSSFS file server )