Difference between revisions of "1. Using RKTool RSB-4810 Debain"
Xingxing.li (talk | contribs) |
Xingxing.li (talk | contribs) |
||
| Line 21: | Line 21: | ||
[[File:RSB-4810 rock.png|RTENOTITLE]] | [[File:RSB-4810 rock.png|RTENOTITLE]] | ||
| + | |||
=== '''Step 4 : The device enters the burn mode''' === | === '''Step 4 : The device enters the burn mode''' === | ||
a ) A data cable with male USB connectors at both ends is available. | a ) A data cable with male USB connectors at both ends is available. | ||
| + | |||
| + | [[File:RSB-4810 USB both.png]] | ||
b ) Connect jumper cap J4 to Pin1 - Pin2(set USB-otg mode). | b ) Connect jumper cap J4 to Pin1 - Pin2(set USB-otg mode). | ||
Note：Default jumper cap J4 Connect Pin2-Pin3 (Set USB-host mode) | Note：Default jumper cap J4 Connect Pin2-Pin3 (Set USB-host mode) | ||
| + | |||
| + | [[File:RSB-4810 J4 setting.png]] | ||
c ) Connect one part of the USB cable to the USB port below and the other end to the computer. | c ) Connect one part of the USB cable to the USB port below and the other end to the computer. | ||
| + | |||
| + | [[File:RSB-4810 USB conjoint.png]] | ||
d ) Jump the J1 jumper cap to Pin1-Pin2, then switch on the 12V power supply. | d ) Jump the J1 jumper cap to Pin1-Pin2, then switch on the 12V power supply. | ||
| + | |||
| + | [[File:RSB-4810 J1 setting.png]] | ||
e ) Then the burning tool will appear: a MASKROM word found. | e ) Then the burning tool will appear: a MASKROM word found. | ||
Revision as of 06:50, 19 October 2023
Contents
- 1 Step 0 : For example, the PC used is a laptop. The specifications are as follows：
- 2 Step 1 ：Extract Driver Assitant_v5.11.zip and follow these steps: Mounting driver.
- 3 Step 2 : Go to the RKDevTool_Release folder and run the RKDevTool.exe program
- 4 Step 3 : Ensure that the path to the burned file is correct
- 5 Step 4 : The device enters the burn mode
Step 0 : For example, the PC used is a laptop. The specifications are as follows：
Decompress the downloaded image on the PC.
Step 1 ：Extract Driver Assitant_v5.11.zip and follow these steps: Mounting driver.
Run the installer and wait for the installation to succeed
Step 2 : Go to the RKDevTool_Release folder and run the RKDevTool.exe program
Step 3 : Ensure that the path to the burned file is correct
Step 4 : The device enters the burn mode
a ) A data cable with male USB connectors at both ends is available.
b ) Connect jumper cap J4 to Pin1 - Pin2(set USB-otg mode).
Note：Default jumper cap J4 Connect Pin2-Pin3 (Set USB-host mode)
c ) Connect one part of the USB cable to the USB port below and the other end to the computer.
d ) Jump the J1 jumper cap to Pin1-Pin2, then switch on the 12V power supply.
e ) Then the burning tool will appear: a MASKROM word found.
Note：Suspend or shut down the virtual machine during this process; otherwise, the pop-up information may affect the burning results.
f ) Jump the J1 jumper cap back to Pin2-Pin3 and click "Execute"
g ) Just wait patiently for the burning to finish.