Difference between revisions of "How to use UART for RK3399 RSB4710"
Xingxing.li (talk | contribs) |
|||
| (2 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| + | |||
= '''Overview''' = | = '''Overview''' = | ||
| Line 15: | Line 16: | ||
== RSB4710 Borad == | == RSB4710 Borad == | ||
| − | {| border="1" | + | {| border="1" cellpadding="1" cellspacing="1" |
|- | |- | ||
| '''COM Name''' | | '''COM Name''' | ||
| Line 22: | Line 23: | ||
|- | |- | ||
| COM0 | | COM0 | ||
| − | | /dev/ttyS0 | + | | /dev/ttyS0 |
| − | | pull to M2 interface for BT using | + | | pull to M2 interface for BT using |
|- | |- | ||
| − | | COM1 | + | | COM1 |
| − | | /dev/ttyS4 | + | | /dev/ttyS4 |
| − | | support RS232, no flow control | + | | support RS232, no flow control |
|- | |- | ||
| − | | COM2 | + | | COM2 |
| − | | /dev/ttyS2 | + | | /dev/ttyS2 |
| − | | Debug Port | + | | Debug Port |
|- | |- | ||
| − | | COM3 | + | | COM3 |
| − | | /dev/ttyUSB0 | + | | /dev/ttyUSB0 |
| − | | support RS232 | + | | support RS232 |
|- | |- | ||
| COM4 | | COM4 | ||
| − | | /dev/ttyUSB1 | + | | /dev/ttyUSB1 |
| − | | support RS232 | + | | support RS232 |
|- | |- | ||
| − | | COM5 | + | | COM5 |
| /dev/ttyUSB2 | | /dev/ttyUSB2 | ||
| support RS232 and RS485 | | support RS232 and RS485 | ||
|- | |- | ||
| − | | COM6 | + | | COM6 |
| − | | /dev/ttyUSB3 | + | | /dev/ttyUSB3 |
| − | | support RS232 and RS485 | + | | support RS232 and RS485 |
|} | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''Note : ''' | '''Note : ''' | ||
| Line 95: | Line 88: | ||
</pre> | </pre> | ||
| − | + | '''RS422 Mode: (ADS-B3399G)''' | |
| + | <pre>setenv uart_mode 0xf | ||
| + | saveenv | ||
| + | reset | ||
| + | </pre> | ||
'''Note : ''' | '''Note : ''' | ||
| Line 106: | Line 103: | ||
If you just want ttyUSB2 (or ttyUSB3)to be RSB485 mode, please change 0x0c to 0x04 (or 0x08). | If you just want ttyUSB2 (or ttyUSB3)to be RSB485 mode, please change 0x0c to 0x04 (or 0x08). | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 02:26, 11 May 2022
Contents
Overview
The Android/Linux UART/serial port access from user is through the tty-devices. The tty-devices have different names depending on UART driver on different board.
RS-485
RS-485 uses half-duplex communication, which means that one medium is shared for transmitting and receiving data.
Therefore the system needs to control the RS-485 transceiver's transmit mode.
Usually the UART RTS signal is used to switch the transmitter on and off.
Boards
RSB4710 Borad
| COM Name | Device Node | Remark |
| COM0 | /dev/ttyS0 | pull to M2 interface for BT using |
| COM1 | /dev/ttyS4 | support RS232, no flow control |
| COM2 | /dev/ttyS2 | Debug Port |
| COM3 | /dev/ttyUSB0 | support RS232 |
| COM4 | /dev/ttyUSB1 | support RS232 |
| COM5 | /dev/ttyUSB2 | support RS232 and RS485 |
| COM6 | /dev/ttyUSB3 | support RS232 and RS485 |
Note :
1. Only COM4、USB2COM0、USB2COM1、USB2COM2、USB2COM3 are designed for custom using.
2. Only USB2COM2 and USB2COM3 support RSB485.
3. COM2 is designed as debug port default.
How to config RS232 or RS485 mode
Enter U-boot interrupt mode
Connect device to debug port, and open debug console. See more : How_to_debug.
Press "ctrl + c" key before power up the device, until get the following information on debug console :
Hit any key to stop autoboot: 0 => <INTERRUPT> =>
Then you can input the following cammand to config UART mode.
Config Uart Mode
Only ttyUSB2 and ttyUSB3 support RS485 mode.
RS485 Mode:
setenv uart_mode 0x0c saveenv reset
RS232 Mode:
setenv uart_mode 0x00 saveenv reset
RS422 Mode: (ADS-B3399G)
setenv uart_mode 0xf saveenv reset
Note :
The default value is RS232.
Cp210x support four port, but RSB4710 Only ttyUSB2 and ttyUSB3 support RS485 mode.
Above command "setenv uart_mode 0x0c", 0x0c means set bit2(ttyUSB2) and bit3(ttyUSB3) to 1 (0 means to RS232; 1 means to RS485).
If you just want ttyUSB2 (or ttyUSB3)to be RSB485 mode, please change 0x0c to 0x04 (or 0x08).