Difference between revisions of "RSB-3710 user guide Android7.12"

Latest revision as of 02:05, 26 September 2024

產品介紹(Product introduction )

產品特性(Product Features)

• Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz
• Onboard LPDDR4 2GB
• HDMI 1920x1080 at 60Hz, 1 Dual Channel 24 bit LVDS
• 1 2-wire RS-232, 1 USB3.0, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
• 1 mini-PCIe for 3G/4G
• UIO expansion 3 USB2.0, 8 GPIO, 2 RS232 2/2-wires UART, 1 I2C
• Supports Debian9/10 and Android7.1/10.0
• Support I/O Expansions by UIO40-Express I/O boards, please refer to page #3 for more information

產品官網連結(Product Features) 

RSB-3710

硬件接口說明(Hardware interface introduction)

接口布局和尺寸(Layout and Sizes)

接口布局圖 Board Dimension Layout 

 Connector List

接口引脚定義 (Pin definitions)

• BAT
• HDMI1
• BL
• LVDS
• LAN1, LAN2
• MINIPCIE
• SIM
• Audio
• USB1
• COM2/Debug
• SD
• OTG
• BTN
• RST
• DCIN1
• LED
• CN11
• CN12
• RSB-3710_Jumper List

机械尺寸  (Mechanical Characteristics)

快速入门 (Quick Start)

系统下载 ( OS Download)

Note：  LIV=Yocto Linux, UIV=Ubuntu, DIV=Debian, AIV=Android

             LBV=BSP, LIV=Image

• Alpha:  Basic I/O function bring up by RD;

• Beta:  Basic I/O function、performance and middleware verified by RD. Peripherals integrated;

• GA:  Beta version by QE verification;

• RTM:  Beta version by SI/Power/QE verification and pre-loaded;

Android 燒錄方法 (Flash Android image into eMMC Method) 

1. Prepare a mirco USB Cable and Debug Cable 

 mirco USB 

Debug Cable 

2. Plug the OTG Cable into RSB-3720 

Connect Debug cable 

2. 設定終端機(Set Debug Terminal) 

Debug 串口調試 (Debug port Setting)

 Tera Term setting 

   Baud Rate：115200
   Data ：8
   Parity ：none
   Stop ：1
   Flow Control：none

Tera Term Tool 

Note:

Check the Sriel port in Device Manager ：

if you can not identify the Serial device , please check your serial driver. 

3.Open the flash tool 

4. Turn on the power 

5. When you see the debug message in Terminal , then press "Ctrl+C" , then log into Uboot stage 

6. In Uboot , please type  "loader"  , then the device will transfer to "Flash mode"  , Android tool also will show  "Found One MASKROM Device " 

7. In RKDevTool pressed  "Run"  , and it will flash image into eMMC.

8. The flash process  was finishded 

9. Reboot the device , and connect with HDMI , it will show the Android Desktop. 

Debian 燒錄方法 ( Flash Debian image into eMMC Method) 

1. Prepare a  mirco USB cable and Debug Cable 

 mirco USB 

Debug Cable 

2. plug  mirco USB cable into the  RSB-3710 OTG port. 

Connect  Debug cable 

3. 設定終端機(Set Debug Terminal) 

Debug 串口調試 (Debug port Setting)

   Baud Rate：115200
   Data ：8
   Parity ：none
   Stop ：1
   Flow Control:none

Tera Term Tool 

Note:

查看PC端的串口号(Check the Sriel port in Device Manager) :

如果沒有找到 請先確認是否有安裝驅動(if you can not identify the Serial device , please check your serial driver.) 

3. Execute the Flash tool 

4. Turn on the power. 

5. Press "Ctrl + C", log into u-boot 

6. In Uboot , please type "rbrom "  , the device will transfer to"Flash mode" , Android tool also will show "Found One MASKROM Device " 

 7. In RKDevTool , Press "Run" , it will flash the image into eMMC. 

8.  The flash process  was finishded 

9. Reboot the device , and connect with HDMI , it will show the Debian Desktop. 

系统的基本使用(Linux System Basic Operating Method)

Display Setting (RSB-3710)

In u-boot:

=> setenv prmry_screen lvds-g070vw01

=> setenv extend_screen hdmi-default

=> saveenv

=> reset

In Linux:

~# fw_setenv prmry_screen lvds-g070vw01

~# reboot

Modify LVDS backlight PWM: (Defaul is 20KHz, New version BSP support to modify the PWM clock in u-boot from 200~20KHz)

In u-boot:

=> setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)

In Linux:

~# fw_setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)

~# reboot

Check PWM duty sysle in Linux:

~# cat /sys/kernel/debug/pwm

乙太網路使用方法(Ethernent Testing Method)

Command : ifconfig 

Command: Ping 8.8.8.8 

WiFi使用方法(WIFI Testing Method)

# killall wpa_supplicant
# ifconfig wlan0 up
# wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf
# cat /tmp/wpa.conf
# wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
# udhcpc -b -i wlan0
# ifconfig
# ping 8.8.8.8
Add DNS to /etc/resolv.conf
# cat /etc/resolv.conf
# Generated by Connection Manager
nameserver 8.8.8.8
nameserver 8.8.4.4
Now can ping google.com
# ping google.com

4G使用方法(4G Testing Method)

Ubuntu - 4G 模塊(EC-25J) 設定 ( 4G module (EC-25J) in Ubuntu system) 

Ubuntu - 4G 模塊(EC-20) 設定( 4G module (EC-20) in Ubuntu system) 

GPIO使用方法(GPIO Operating Method)

蓝牙使用方法(BlueTooth Operating Method)

# hciattach /dev/ttymxc0 bcm43xx 115200 flow
# hciconfig hci0 up
# hcitool scan# bluetoothctl
# discoverable on
#pairable on
# scan on
# scan off
# pair 84:C5:A6:D3:AF:E4
# connect 84:C5:A6:D3:AF:E4
Check BT connect info
# info 84:C5:A6:D3:AF:E4

音訊使用方法(BlueTooth Operating Method)

Line-in , Line-out, MIC
1.Line-out
Command : gplay-1.0
2.MIC
Command : arecord
Check audio codec:

# cat /proc/asound/cards
 0 [sgtl5000       ]: sgtl5000 - sgtl5000
                      sgtl5000
 1 [audiohdmi      ]: audio-hdmi - audio-hdmi
                      audio-hdmi
root@imx8mprsb3720a1:~#
   Set Mic/audio volume
# amixer set Mic 100%
# amixer set Lineout 100%
# amixer set PCM 100%

Record and playback
Example command:
# arecord –t wav –c 1 –r 44100 –d 5 /tmp/mic.wav
# aplay /tmp/mic.wav

Record from MIC:
# arecord -D plughw:0,0 -r 16000 -f S16_LE ./f-16000.wav
Recording WAVE './f-16000.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono
# aplay f-16000.wav
Playing WAVE 'f-16000.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono

Play wav file from codec:
# aplay -D plughw:0,0 file_example_WAV_10MG.wav
Playing WAVE 'file_example_WAV_10MG.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

Play wav file from HDMI:
# aplay -D plughw:1,0 file_exam
ple_WAV_10MG.wav
Playing WAVE 'file_example_WAV_10MG.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo

看門狗測試 (Watch Dog Test method) 

System will reboot after 1 sec
# /unit_tests/Watchdog/wdt_driver_test.out 1 2 0

遠程訪問及文件傳輸(Remote Access and File Transimmion)

              查看主板IP位址 ( Chech IP Address )：​

        Command : ifconfig

Windows下SSH访问及文件传输

SSH Remote Log into Device 

• SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
• 需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码

通用方法(General Method)

查看CPU温度(Check CPU Temperature)

root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp   
40000
# 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° 
>> 40°

查看CPU频率(Check CPU Frequency)

cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq 
>> 1200000
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq    
>> 1800000

查看内存容量(Check Memory Capacity)

root@linaro-alip:~# busybox free -m
              total        used        free      shared  buff/cache   available
Mem:           1961         303        1096          97         561        1575
Swap:             0           0           0
root@linaro-alip:~#

查看存储容量(Check Storage Capacity)

root@linaro-alip:~# busybox df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 7.8G      2.8G      4.6G  37% /
devtmpfs                972.3M      8.0K    972.3M   0% /dev
tmpfs                   980.8M         0    980.8M   0% /dev/shm
tmpfs                   980.8M     16.8M    964.0M   2% /run
tmpfs                     5.0M      4.0K      5.0M   0% /run/lock
tmpfs                   980.8M         0    980.8M   0% /sys/fs/cgroup
/dev/mmcblk1p10           6.4G      3.8M      6.4G   0% /userdata
/dev/mmcblk1p7           62.6M     12.0M     47.3M  20% /oem
tmpfs                   196.2M         0    196.2M   0% /run/user/0
tmpfs                   196.2M      8.0K    196.1M   0% /run/user/1000
root@linaro-alip:~#

網路Ping測試(Ping Network Testing)

ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms

設置RTC (RTC Setting) 

Set system time to current, then write to RTC
root@linaro-alip:~# date 01282022
Fri Jan 28 20:22:00 UTC 2022
root@linaro-alip:~#
Restart the RTC time to system time
# hwclock -s && date

root@linaro-alip:~# hwclock -s && date
Thu Jan 20 06:18:26 UTC 2022
root@linaro-alip:~# 

Android BSP編譯方法(Android BSP Compile Method)

http://ess-wiki.advantech.com.tw/view/Debian_BSP_User_Guide_for_rk3399_risc_series 

如果有驗證上的錯誤 請使用以下的方法(If you got " Server certificate verification failed " message ,please follow the solution as below) 

### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none
============================================================
export GIT_SSL_NO_VERIFY=1
#or
git config --global http.sslverify false
============================================================