Difference between revisions of "IoTGateway/BSP/Linux/iMX6/Mfgtool"
From ESS-WIKI
| Line 6: | Line 6: | ||
--> | --> | ||
| − | = | + | =Enter recovery mode= |
===ROM-5420=== | ===ROM-5420=== | ||
:Set the correct boot mode, then power on. | :Set the correct boot mode, then power on. | ||
| Line 19: | Line 19: | ||
:[[File:other_project_mfgtool.jpg|200px]] | :[[File:other_project_mfgtool.jpg|200px]] | ||
| − | + | =Connect the OTG to the PC= | |
| − | |||
:After connecting to PC, a HID-compliant device will be shown in the Device | :After connecting to PC, a HID-compliant device will be shown in the Device | ||
:[[File:dm_mfgtool.jpg |500px]] | :[[File:dm_mfgtool.jpg |500px]] | ||
| − | = | + | =Modify config file= |
==modify cfg.ini== | ==modify cfg.ini== | ||
:path: mfgtools/cfg.ini | :path: mfgtools/cfg.ini | ||
| Line 53: | Line 52: | ||
mmc = ( “0” means “emmc” ,”1” means “SD Card” .) | mmc = ( “0” means “emmc” ,”1” means “SD Card” .) | ||
image = (If you want to update whole image,fill the image file name ) | image = (If you want to update whole image,fill the image file name ) | ||
| + | After updating image | ||
| + | #then power on system | ||
| + | #perform “resize2fs /dev/mmcblk0p2” | ||
| + | #restart system. | ||
| + | |||
| + | =Running mfgtool and update= | ||
| + | running the MfgTool2.exe and update | ||
| + | :[[File:Mfgtool.jpg |400px]] | ||
| + | #If you can’t running mfgtool2.exe, you can check MfgTool.log | ||
| + | #Click “Start”,you can get information form debug console | ||
| + | #:[[File:Debug mfgtool.jpg |600px]] | ||
| + | #After update finish,it will be shown below | ||
| + | #:[[File:Mfgtool2.jpg |400px]] | ||
| + | #Click “Exit” to terminate the application. | ||
Revision as of 03:58, 3 June 2016
User Guide for using mfgtool
Enter recovery mode
ROM-5420
- Set the correct boot mode, then power on.
ROM-3420
- ATX mode
- In power off state,press power key for 5 secs and release
- AT mode
- Press power key ,then plug AC adapter,release power key after 5 secs
Other Projects
- Set end mode,then power on(1-off,2-on)
Connect the OTG to the PC
- After connecting to PC, a HID-compliant device will be shown in the Device
Modify config file
modify cfg.ini
- path: mfgtools/cfg.ini
[profiles] chip = Linux [platform] board = SabreSD [LIST] name = ADV u-boot [variable] dtb = imx6dl-rom5420-b1 mmc = 0 image = fsl-image-x11-imx6qrom5420-20141218174618.rootfs.sdcard
which operation you want to do
[LIST] name = ADV Image update whole image(including rootfs) ADV kernel update zImage and dtb file ADV u-boot update u-boot ADV adv-loader update adv-loader
define config variable
[variable] dtb = (name of dtb file) mmc = ( “0” means “emmc” ,”1” means “SD Card” .) image = (If you want to update whole image,fill the image file name )
After updating image
- then power on system
- perform “resize2fs /dev/mmcblk0p2”
- restart system.
Running mfgtool and update
running the MfgTool2.exe and update
- If you can’t running mfgtool2.exe, you can check MfgTool.log
- Click “Start”,you can get information form debug console
- After update finish,it will be shown below
- Click “Exit” to terminate the application.
