Difference between revisions of "User Guide 4710 Android 7.1.2"
From ESS-WIKI
Xingxing.li (talk | contribs) (→通用方法(General Method)) |
Xingxing.li (talk | contribs) (→通用方法(General Method)) |
||
| Line 129: | Line 129: | ||
*[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_Debian9_for_rk|Linux BSP User Guide for rk3399 series Debian9]] <br/> *[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_DeviceOn|Linux BSP User Guide for rk3399 series DeviceOn]] <br/> *[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_SGI|Linux BSP User Guide for SGI [DMS-SA53]]] | *[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_Debian9_for_rk|Linux BSP User Guide for rk3399 series Debian9]] <br/> *[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_DeviceOn|Linux BSP User Guide for rk3399 series DeviceOn]] <br/> *[[IoTGateway/BSP/Linux/Linux_BSP_User_Guide_SGI|Linux BSP User Guide for SGI [DMS-SA53]]] | ||
| + | |||
== '''通用方法(General Method)''' == | == '''通用方法(General Method)''' == | ||
| − | How to debug | + | === [[How_to_debug_for_RSB-4710|'''How to debug''']] === |
| − | How to use GPIO | + | === [[How_to_use_GPIO_for_RSB-4710|'''How to use GPIO''']] === |
| − | How to use UART | + | === [[How_to_use_UART_for_RSB-4710|'''How to use UART''']] === |
| − | How to config Multi-Display | + | === [[How_to_config_Multi-Display_for_RSB-4710|'''How to config Multi-Display''']] === |
| − | How to Config I2S | + | === [[How_to_Config_I2S_for_RSB-4710|'''How to Config I2S''']] === |
| − | How to use I2C Hub | + | === [[How_to_use_I2C_Hub_for_RSB-4710|'''How to use I2C Hub''']] === |
| − | How to use MIPI Camera | + | === [[How_to_use_MIPI_Camera_for_RSB-4710|'''How to use MIPI Camera''']] === |
| − | How to Config 4G-module | + | === [[How_to_Config_4G-module_for_RSB-4710|'''How to Config 4G-module''']] === |
=== '''乙太網路使用方法(Ethernent Testing Method)''' === | === '''乙太網路使用方法(Ethernent Testing Method)''' === | ||
Revision as of 01:51, 25 September 2024
Contents
- 1 產品介紹(Product introduction )
- 2 硬件接口說明(Hardware interface introduction)
- 3 Connector List
- 4 快速入门 (Quick Start)
- 5 Linux系统的基本使用(Linux System Basic Operating Method)
- 6 通用方法(General Method)
- 6.1 How to debug
- 6.2 How to use GPIO
- 6.3 How to use UART
- 6.4 How to config Multi-Display
- 6.5 How to Config I2S
- 6.6 How to use I2C Hub
- 6.7 How to use MIPI Camera
- 6.8 How to Config 4G-module
- 6.9 乙太網路使用方法(Ethernent Testing Method)
- 6.10 查看CPU温度(Check CPU Temperature)
- 6.11 查看CPU频率(Check CPU Frequency)
- 6.12 查看内存容量(Check Memory Capacity)
- 6.13 查看存储容量(Check Storage Capacity)
- 6.14 設置RTC (RTC Setting)
- 7 How to build Android 7 BSP (Android 7 BSP 編譯)
產品介紹(Product introduction )
產品特性(Product Features)
- Rockchip RK3399 ARM Dual Cortex-A72 and Quad Cortex-A53 1.8 GHz
*Onboard 2GB LPDDR4 memory and 16GB eMMC
*Dual HDMI(4K 60fps + 1080P), 1 x eDP, 1 x dual channel LVDS, 1 x MIPI CSI
*Supports 4K H.264/H.265 video decoder
*6 x serial, 1 x USB3.0, 4 x USB2.0 ,1 x USB OTG, 2 x GbE, 1 x SPI, 1 x I2C, 5 x GPIOs
*M.2 for WIFI/BT support, mini-PCIe for 3G/4G support
*Supports Debian9/10 and Android7.1/10.0
產品官網連結(Product Features)
硬件接口說明(Hardware interface introduction)
接口布局和尺寸(Layout and Sizes)
接口布局圖 Board Dimension Layout
Connector List
接口引脚定義 (Pin definitions)
- 电池扣（RTC）
*串口（RS-232 (COM1)，RS-232/Debug Port (COM2/DEBUG)，RS-232/485 (COM56)，Internal RS-232 (COM34)）
*显示接口（LVDS,LVDS_BL,EDP,HDMI）
*LAN接口（LAN1，LAN2）
*USB接口（USB1，Pin Header，OTG）
*音频接口（Audio）
*Micro SD & Nano SIM Card
*电源及指示灯和开关机复位按钮（DC Power，Power Button and LED）
*Mini PCIe & MIPI CSI 接口
*M.2接口
*GPIO接口
*SPI ，I2C接口
*RSB-4710 Jumper List
机械尺寸 (Mechanical Characteristics)
快速入门 (Quick Start)
系统下载 (OS Download)
Android7.12
Note： AIV=Android image ABV=BSP
| Product | Image Version | Release Date | Release Version | Release notes | Image Download | BSP Download Tag | Comment |
| RSB-4710 | V1180 | 2020/08/27 | RTM | Release_Note |
Baidu Password：a887 |
RK3399_N7_AIV1180.xml |
- Alpha: Basic I/O function bring up by RD;
- Beta: Basic I/O function、performance and middleware verified by RD. Peripherals integrated;
- GA: Beta version by QE verification;
- RTM: Beta version by SI/Power/QE verification and pre-loaded;
Android 燒錄方法 (Android Flash eMMC Method)
There are three ways to update images：
1.Using_AndroidToool.
There is no limitation by this way.
2.Using_storage（such sd_or_USB_disk）with_update.zip_in_it.
There are some limitations：
（1）The device must be able to boot up to Android system.
（2）Only update images from the same os, eg :
Android6.0 upgrade to Android6.0 or Android7.1 upgrade to Android7.1.
（3）Using update.zip to upgrade. (see more detail in "Create OTA zip" on how to create update.zip)
3.Using_bootup_sd_disk made_by SDDiskTool.
（1）Only update images from the same os, eg :
Android6.0 upgrade to Android6.0 or Android7.1 upgrade to Android7.1.
（2）Using update.img to upgrade.
Linux系统的基本使用(Linux System Basic Operating Method)
User Guide
RISC series(RSB-3710/RSB-4710/ROM-5780)
- Linux BSP User Guide for rk3399 series Debian9/Debian10
- Getting Start
- MAC_Address
- Android signature
- Install Jave in Linux
DS-100
- Linux BSP User Guide for rk3399 series Debian9
*Linux BSP User Guide for rk3399 series DeviceOn
*Linux BSP User Guide for SGI [DMS-SA53]
通用方法(General Method)
How to debug
How to use GPIO
How to use UART
How to config Multi-Display
How to Config I2S
How to use I2C Hub
How to use MIPI Camera
How to Config 4G-module
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
root@linaro-alip:~# ifconfig docker0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet 172.17.0.1 netmask 255.255.0.0 broadcast 172.17.255.255 ether 02:42:83:27:77:c0 txqueuelen 0 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.127.101 netmask 255.255.255.0 broadcast 192.168.127.255 inet6 fe80::e405:b000:5963:d697 prefixlen 64 scopeid 0x20<link> ether c6:ff:6c:34:9d:7d txqueuelen 1000 (Ethernet) RX packets 23 bytes 7566 (7.3 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 45 bytes 5391 (5.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 24 eth1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether 96:a4:98:8d:52:09 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1 (Local Loopback) RX packets 484 bytes 32428 (31.6 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 484 bytes 32428 (31.6 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Command : ping 192.168.127.101
root@linaro-alip:~# ping 192.168.127.101 PING 192.168.127.101 (192.168.127.101) 56(84) bytes of data. 64 bytes from 192.168.127.101: icmp_seq=1 ttl=64 time=0.221 ms 64 bytes from 192.168.127.101: icmp_seq=2 ttl=64 time=0.135 ms 64 bytes from 192.168.127.101: icmp_seq=3 ttl=64 time=0.134 ms 64 bytes from 192.168.127.101: icmp_seq=4 ttl=64 time=0.137 ms 64 bytes from 192.168.127.101: icmp_seq=5 ttl=64 time=0.137 ms ^C --- 192.168.127.101 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 5ms rtt min/avg/max/mdev = 0.134/0.152/0.221/0.037 ms root@linaro-alip:~#
查看CPU温度(Check CPU Temperature)
root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 34444 # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 37°
查看CPU频率(Check CPU Frequency)
root@linaro-alip:~# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq 408000 root@linaro-alip:~# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq 1416000
查看内存容量(Check Memory Capacity)
root@linaro-alip:~# busybox free -m total used free shared buff/cache available Mem: 1961 269 1454 18 237 1696 Swap: 0 0 0
查看存储容量(Check Storage Capacity)
root@linaro-alip:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/root 7.9G 2.6G 4.9G 35% / devtmpfs 973M 8.0K 973M 1% /dev tmpfs 981M 0 981M 0% /dev/shm tmpfs 981M 8.9M 972M 1% /run tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 981M 0 981M 0% /sys/fs/cgroup /dev/mmcblk1p10 6.4G 3.8M 6.4G 1% /userdata /dev/mmcblk1p7 63M 13M 48M 21% /oem tmpfs 197M 8.0K 197M 1% /run/user/1000 tmpfs 197M 0 197M 0% /run/user/0 root@linaro-alip:~#
設置RTC (RTC Setting)
root@linaro-alip:~# date
Wed May 11 01:12:06 UTC 2022
root@linaro-alip:~# date -s "2022-5-11 09:12:00"
Wed May 11 09:12:00 UTC 2022
root@linaro-alip:~# date
Wed May 11 09:12:06 UTC 2022
root@linaro-alip:~# hwclock -w
root@linaro-alip:~# hwclock
2022-05-11 09:12:17.266424+00:00How to build Android 7 BSP (Android 7 BSP 編譯)
http://ess-wiki.advantech.com.tw/view/Android_BSP_User_Guide_for_rk3399_series_7.1.2