SNMP-NMS

From ESS-WIKI
Revision as of 08:43, 15 January 2019 by Sam35.lin (talk | contribs) (.)
Jump to: navigation, search

Introduction

Simple Network Management Protocol (SNMP) is an Internet Standard protocol for collecting and organizing information about managed devices on IP networks and for modifying that information to change device behavior. Devices that typically support SNMP include cable modems, routers, switches, servers, workstations, printers, and more.

An SNMP-managed network consists of three key components:

  • Managed devices
  • Agent – software which runs on managed devices
  • Network management station (NMS) – software which runs on the manager


EdgeSense SNMP-NMS

EdgeSense SNMP-NMS is a plug-in of RMM agent, aim to collect  object data from SNMP managed device.

Feature:

  • Support SNMPv1, SNMPv2c.
  • support object type: OCTET STRING, Integer32
  • Currently support up-link object's value to WISE-PaaS , not support down-link from WISE-PaaS.

SNMP-NMS topology2.jpg


How to

Software Installation for Ubuntu 16.04

Install Steps:

1. Install OS - Ubuntu 16.04 (ex: ubuntu-16.04.5-desktop-amd64.iso)

2. Install MQTT Broker

Copy MQTT Broker install package (ex: MQTTBrokerSetup-1.0.4-Ubuntu_16.04-x86_64.run) to gateway.

$ sudo chmod +x MQTTBrokerSetup-1.0.4-Ubuntu_16.04-x86_64.run
$ sudo ./MQTTBrokerSetup-1.0.4-Ubuntu_16.04-x86_64.run

3. Install EdgeSense SNMP-NMS

Copy SNMP-NMS install package (ex: SNMP-NMS-1.0.0-Ubuntu_16.04-x86_64.run) to gateway.

$ sudo chmod +x SNMP-NMS-1.0.0-Ubuntu_16.04-x86_64.run
$ sudo ./SNMP-NMS-1.0.0-Ubuntu_16.04-x86_64.run

After installation, service will be autorun.

NOTE: Please wire the gateway to Internet with Network cable before install, it is necessary to install the dependencies. 

Uninstall Steps:

$ sudo /usr/local/EdgeSense/SNMP-NMS/uninstall.bash

4. Install WISE-PaaS agent

Turn MIBs file into JSON documentation

Because MIBS file is not good to load in application, EdgeSense SNMP-NMS use a tool from PySMI to turn MIBS file into json file.

About installing PySMI or more detailed, please refer to this.

Usage:

mibdump.py --generate-mib-texts --destination-format json YOUR_MIB_FILE

example:

mibdump.py --generate-mib-texts --destination-format json ./ADAM-6017.mib

Then a json file will be generated. You can edit this json file to add/remove object you want to poll from several SNMP agents.

Before upload this json file into your system, please make sure this json file is valid. You may paste json file's content in one of below online websites to verify that is valid json file.

At the end, put this json file in folder /usr/local/EdgeSense/SNMP-NMS/config

Configuration

In Ubuntu 16.04

You can modify config file by vi

$ sudo vi /usr/local/EdgeSense/SNMP-NMS/config/snmp_config.json

or modify config file by gedit

$ sudo gedit /usr/local/EdgeSense/SNMP-NMS/config/snmp_config.json

Once config is changed , please restart service in order to apply new setting.

Config File as:

{
  "interval": 20,

  "devicelist" : [
    {
      "devid": "device1",
      "ip": "172.22.12.27",
      "port": 161,
      "snmpver": "2c",
      "community": "public",
      "objectfile" : "ADAM-6017.json"
    },

    {
      "devid": "device2",
      "ip": "172.22.12.27",
      "port": 161,
      "snmpver": "2c",
      "community": "public",
      "objectfile" : "ADAM-6017.json"
    }

  ]
}

interval

  • default value is 20 second
  • If setting is greater than maximum value or is less than minimum value, it will use default value.

Config for a SNMP Agent device include bellow parameter:

devid

  • device id is an identifier, a prefix for SNMP object.
  • Sensor ID will look like devid/object in the WISE-PaaS, ex: device1/firmwareVersion
    RTENOTITLE

ip

  • assign IP of the SNMP Agent device

port

  • assign port of the SNMP Agent device

snmpver

  • assign SNMP ver of the SNMP Agent device

community

  • assign SNMP community of the SNMP Agent device

objectfile

  • assign object file of the SNMP Agent device, converted by pysmi.
  • need to be put on this folder /usr/local/EdgeSense/SNMP-NMS/config

Service control

In Ubuntu

Check if ​service is running:

$ sudo systemctl status SNMP-NMS.service

Restart ​service:

$ sudo systemctl restart SNMP-NMS.service

Start ​service:

$ sudo systemctl start SNMP-NMS.service

Stop ​service:

$ sudo systemctl stop SNMP-NMS.service

Tools

PySMI

PySMI is a open source tool, we use it to turns MIBs into JSON documents.

Installation step:

pip install pysmi

For more detailed information, please refer to PySMI official website.

Reference:

Use Case

Release