RK ALL RF Test

Applications

The following applications have been installed:

wpa_supplicant
chromium
minicom
iperf3

Performance Mode

Configurate CPU GPU NPU and DDR

Configurate CPU GPU NPU and DDR to performance mode at the same time:

# echo performance | tee $(find /sys/ -name *governor)
#

Configurate CPU only

# echo performance | tee $(find /sys/devices/system/cpu/cpufreq/policy* -name *governor)
#

U-Disk

U-Disk will be mounted at /run/media/sda1 automatically.
/run/media/sda1 is most common condition, it may be /run/media/sdb1 /run/media/sdc1.
Plug out U-Disk, see which one is disappeared, and then to plug in U-Disk again.

LTE

How to Configure 4G/5G module :
https://ess-wiki.advantech.com.tw/view/RK_Platform_4G

AT Port

How to find AT Port:

Method 1:

# mmcli -m 0 | grep ttyUSB
           |                   ports: cdc-wdm0 (qmi), ttyUSB4 (qcdm), ttyUSB5 (gps),
           |                          ttyUSB6 (at), ttyUSB7 (at), wwan0 (net)

ttyUSB6 and ttyUSB7 are for the ports for AT command.

Method 2:

# dmesg | grep ttyUSB
[    5.574612] usb 3-1: cp210x converter now attached to ttyUSB0
[    5.586590] usb 3-1: cp210x converter now attached to ttyUSB1
[    5.598584] usb 3-1: cp210x converter now attached to ttyUSB2
[    5.610583] usb 3-1: cp210x converter now attached to ttyUSB3
[   18.535820] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB4
[   18.542643] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB5
[   18.548504] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB6
[   18.553115] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB7

ttyUSB4 to ttyUSB7 are ports for GSM modem.
And ttyUSB6 (the second port counted backwords) is the port for AT command.

Firmware Version

How to get Firmware Version for EC20.
Take ttyUSB6 as AT port, change it according your DUT.

# stty -F /dev/ttyUSB6 9600
# cat /dev/ttyUSB6 &
# echo -e  "ATI\r\n" > /dev/ttyUSB6
Quectel
EC20F
Revision: EC20CEFRGR06A04M4G

OK

EC20CEFRGR06A04M4G is firmware verion.

WLAN

How to Configure WLAN module :
https://ess-wiki.advantech.com.tw/view/RK_Platform_WIFI

wpa_supplicant

Configurate wlan through wpa_supplicant.
Advantech for guest is AP Host and 12345678 is its password. Change them according your condition.

# systemctl stop NetworkManager 
# ifconfig wlan0 up
# iwlist wlan0 scan | grep ESSID 
# wpa_passphrase "Advantech for guest" 12345678 > /tmp/wpa.conf
# wpa_supplicant -d -B -i wlan0 -c /tmp/wpa.conf -Dnl80211 
# udhcpc -i wlan0

Firmware Version

TBD

SDIO Infomation

The sysfs interface provides detailed information on each mmc device:

# cat /sys/kernel/debug/mmc3/ios
clock:          50000000 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      2 (4 bits)
timing spec:    2 (sd high-speed)
signal voltage: 0 (3.30 V)
driver type:    0 (driver type B)