View source for AOM-3841 UART RS232（DEBUG、COM1、COM2、M.2 E1）


=== '''UART''' ===

User Debian/Linux UART/serial port access is through the tty-devices. The ttydevices have different names depending on UART drivers for different boards.

{| border="1" cellpadding="1" cellspacing="1" style="width: 500px;"
|-
| '''Device Node'''
| '''COM Port Name'''
|-
| /dev/ttyFIQ0
| &nbsp;Debug
|-
| /dev/ttyS2
| COM2&nbsp; (COM1_2 connector RS232 2-wire)
|-
| /dev/ttyS4
| COM1&nbsp; (COM1_2 connector RS232 4-wire)
|-
| /dev/ttyS10
| M.2_E1(UART)
|}

=== '''DEBUG Port Connection''' ===

1.Connect the debug port cable on AOM-DB3500.

2.Connect it to your PC with a USB to COM Cable.

{| border="1" cellpadding="1" cellspacing="1" style="width: 254px;"
|-
| colspan="2" style="width: 244px;" | '''DEBUG Pin Connector'''
|-
| style="width: 72px;" | '''Pin'''
| style="width: 169px;" | '''Signal'''
|-
| style="width: 72px;" | 1
| style="width: 169px;" | NC
|-
| style="width: 72px;" | 2
| style="width: 169px;" | RX_DEBUG
|-
| style="width: 72px;" | 3
| style="width: 169px;" | TX_DEBUG
|-
| style="width: 72px;" | 4
| style="width: 169px;" | NC
|-
| style="width: 72px;" | 5
| style="width: 169px;" | GND
|-
| style="width: 72px;" | 6
| style="width: 169px;" | NC
|-
| style="width: 72px;" | 7
| style="width: 169px;" | RTS#
|-
| style="width: 72px;" | 8
| style="width: 169px;" | CTS#
|-
| style="width: 72px;" | 9
| style="width: 169px;" | NC
|}

=== '''Debug Port Settings''' ===

AOM-3841 can communicate with a host server using serial cables. Common serial&nbsp;communication programs such as HyperTerminal, Tera Term, or PuTTY can be used&nbsp;in this case. The example below describes the serial terminal setup using HyperTerminal on a Windows host:<br/> 1. Connect AOM-3841 with your PC using a serial cable.<br/> 2. Open HyperTerminal on your Windows PC, and select the settings demonstrated in the photo below.<br/> 3. Insert a power adapter into the DC jack and power up the board. The Debug&nbsp;console log will be displayed on the terminal screen.

[[File:AOM-3841 debug port.jpg|700x600px|AOM-3841 debug port.jpg]]

=== '''RS232——COM1_2''' ===

[[File:AOM-DB3500 COM1 2.png|700x600px]][[File:AOM-DB3500 COM1 2 Pin header.png]]

{| border="1" cellpadding="1" cellspacing="1" style="width: 476px;"
|-
| colspan="4" style="width: 466px;" | '''COM1_2 Connector, RS232 Mode Pin Definition'''
|-
| style="width: 43px;" | '''Pin'''
| style="width: 156px;" | '''Signal'''
| style="width: 37px;" | '''I/O'''
| style="width: 217px;" | '''Description'''
|-
| style="width: 43px;" | 1
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 2
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 3
| style="width: 156px;" | COM1_RX_485+
| style="width: 37px;" | O
| style="width: 217px;" | COM1 RS232 Receive Data
|-
| style="width: 43px;" | 4
| style="width: 156px;" | COM1_RTS#
| style="width: 37px;" | I
| style="width: 217px;" | COM1 Request to Send
|-
| style="width: 43px;" | 5
| style="width: 156px;" | COM1_TXD_422-
| style="width: 37px;" | I
| style="width: 217px;" | COM1 RS232 Transmit Data
|-
| style="width: 43px;" | 6
| style="width: 156px;" | COM1_CTS#
| style="width: 37px;" | O
| style="width: 217px;" | COM1 Clear to Send
|-
| style="width: 43px;" | 7
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 8
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 9
| style="width: 156px;" | GND
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Ground
|-
| style="width: 43px;" | 10
| style="width: 156px;" | GND
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Ground
|-
| style="width: 43px;" | 11
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 12
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 13
| style="width: 156px;" | COM2_RX_485+
| style="width: 37px;" | O
| style="width: 217px;" | COM2 RS232 Receive Data
|-
| style="width: 43px;" | 14
| style="width: 156px;" | COM2_RTS#
| style="width: 37px;" | I
| style="width: 217px;" | COM2 Request to Send
|-
| style="width: 43px;" | 15
| style="width: 156px;" | COM2_TXD_422-
| style="width: 37px;" | I
| style="width: 217px;" | COM2 RS232 Transmit Data
|-
| style="width: 43px;" | 16
| style="width: 156px;" | COM2_CTS#
| style="width: 37px;" | O
| style="width: 217px;" | COM2 Clear to Send
|-
| style="width: 43px;" | 17
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 18
| style="width: 156px;" | N/A
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Not Applicable
|-
| style="width: 43px;" | 19
| style="width: 156px;" | GND
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Ground
|-
| style="width: 43px;" | 20
| style="width: 156px;" | GND
| style="width: 37px;" | &nbsp;
| style="width: 217px;" | Ground
|}

=== '''Configure Parameters''' ===

Use “stty” command to configure serial port parameters. The commonly used param�eters include “Baud rate”, “Data bits”, “Stop bits”, “Parity”, “Flow control”.

See details of the usage of “stty”:
<pre># stty --help
… …
csN set character size to N bits, N in [5..8]
[-]cstopb use two stop bits per character (one with '-')
[-]parenb generate parity bit in output and expect parity bit in input
[-]crtscts enable RTS/CTS handshaking
…</pre>

For example, set COM1<br/> “Baud rate” to 115200<br/> “Data bits” to 8<br/> “Stop bits” to 1<br/> “Parity” to None<br/> “Flow control” to None
<pre># stty -F /dev/ttyS0 115200 cs8 -parenb -cstopb</pre>

=== '''Send and receive data''' ===

Taking COM1 as receiver or sender (An external COM is required to do the sending&nbsp;or receiving). For example, AOM-3841 is responsible for receiving and inputting&nbsp;instructions. The PC computer is connected via a cable and COM1. The PC computer uses the PuTTY serial port tool, opens the COM port, configures the baud rate&nbsp;to 115200, data bits to 8, stop bits to 1, parity to none, flow control to none, and sends&nbsp;“pass” to the serial port assistant. If no error, the external COM receiver will receive&nbsp;“pass”.
<pre># #---- COM1 as receiver ----# #
# stty -F /dev/ttyS4 115200 cs8 -cstopb -parenb
# cat /dev/ttyS4 &</pre>
<pre># #---- COM1 as sender ----# #
# stty -F /dev/ttyS4 115200 cs8 -cstopb -parenb
# echo pass > /dev/ttyS4
# #----If no error, the external COM receiver will receive “pass”----# #
pass</pre>

Note!

1.Receiver should run before sender.<br/> 2.The "serial port parameters" should be the same for sender and&nbsp;&nbsp;receiver.