Difference between revisions of "Modbus Master"
Line 224: | Line 224: | ||
<span style="font-size:medium;">[[File:Modbus-Slave Modsim32 01.png|700x400px|Modbus-Slave Modsim32 01.png]]</span> | <span style="font-size:medium;">[[File:Modbus-Slave Modsim32 01.png|700x400px|Modbus-Slave Modsim32 01.png]]</span> | ||
− | + | ||
<span style="font-size:medium;">3. Enable Auto Simulation:</span> | <span style="font-size:medium;">3. Enable Auto Simulation:</span> | ||
Line 233: | Line 233: | ||
− | [[File:Modbus-Slave Modsim32 02.png|300x200px]] | + | [[File:Modbus-Slave Modsim32 02.png|300x200px|Modbus-Slave Modsim32 02.png]] |
+ | |||
+ | <span style="font-size: medium;"></span> | ||
− | <span style="font-size: medium;">4. Set | + | <span style="font-size: medium;">4. Set simulation parameters:</span> |
*<span style="font-size:medium;">Check "Enable"</span> | *<span style="font-size:medium;">Check "Enable"</span> | ||
Line 246: | Line 248: | ||
*<span style="font-size:medium;">High Limit: 20</span> | *<span style="font-size:medium;">High Limit: 20</span> | ||
− | + | [[File:Modbus-Slave Modsim32 03.png|360x280px|Modbus-Slave Modsim32 03.png]] | |
− | + | <span style="font-size:medium;"><br/></span> | |
+ | <span style="font-size:medium;">5. Do the same step for the address 40002 and set simulation parameter as below:</span> | ||
+ | *<span style="font-size:medium;">Simulation Type: Increment<br/></span> | ||
+ | *<span style="font-size:medium;">Low Limit: 60</span> | ||
+ | *<span style="font-size:medium;">High Limit: 80</span> | ||
<span style="font-size:medium;"></span> | <span style="font-size:medium;"></span> |
Revision as of 09:46, 10 January 2020
Contents
Introduction
Modbus enables communication among many devices connected to the same network, for example, a system that measures temperature and humidity and communicates the results to a computer. Modbus is often used to connect a supervisory computer with a remote terminal unit (RTU) in supervisory control and data acquisition (SCADA) systems.
Many of the data types are named from its use in driving relays: a single-bit physical output is called a coil, and a single-bit physical input is called a discrete input or a contact.
Modbus Service is a Windows/Linux system service for WISE Agent to read sensor data from Modbus device or write data into Modbus device. After sensor data are acquired, WISE Agent will upload the data to the WISE-PaaS Cloud.
Features
EdgeSense Modbus-Master aims to collect data from Modbus Slave.
Feature:
- Support connection with multiple Modbus slave.
- Support Modbus TCP and Modbus RTU.
- Support individual sensor upload interval.
- Configurable sensor alias.
- Support byte swap.
- Currently support up-link Modbus data to WISE-PaaS , not support down-link from WISE-PaaS.
How to
Software Requirements
- MQTT broker
- Node.js
Installation
Windows:
1. Download Modbus-Master for Windows from Release Table.
2. Double click the installer to launch the installer to install it to the machine.
Linux:
N.A.
Configuration
EdgeSense Modbus Master can manage multiple Modbus Slave setting and individual sensor's parameters, below settings are default after Modbus Master installation.
1. Device Configuration: <Install_folder>\config\industry\device-industry.yaml
metadata: name: "Modbus devices" labels: ["Modbus"] Description: "Modbus TCP/RTU devices with 3 sensors in holding register area 40001~40003" UpdateData: 2020-01-08-14:25:30 # DeviceInfo: You can add a new device with unique name # <DeviceName>: Unique Device Name # Params: LinkInfo: COM1: Params: Driver: Modbus-RTU ConnectType: Serial PortName: COM1 BaudRate: 9600 DataBits: 8 StopBits: 1 Parity: None Info: PollingInterval: 1000 # Polling interval ( milliseconds ) Timeout: 100 # A request timeout ( milliseconds ) Retry: 3 # Retries min:0 max:3 ( count ) AliveTime: 60 # Link Timeout in second: SDK will release this link if there are any request over this AliveTime ( second ) CheckLinkInterval: 5 # Check link status interval (second) DevList: - Device-1 TCP-IP-1: Params: Driver: Modbus-TCP ConnectType: Net IP: 127.0.0.1 Port: 502 Info: PollingInterval: 1000 # Polling interval in milliseconds Timeout: 100 # A request timeout in milliseconds Retry: 3 # Count of retry min:0 max:3 AliveTime: 60 # Link Timeout in second: SDK will release this link if there are any request over this AliveTime ( second ) CheckLinkInterval: 5 # Check link status interval (second) DevList: - Device-2 DeviceInfo: Device-1: Params: Station: 1 Profile: MODBUS_DEVICE_01.yaml Device-2: Params: Station: 2 Profile: MODBUS_DEVICE_02.yaml
2. Sensor Configuration for Device-1: <Install_folder>\config\industry\Profile\MODBUS_DEVICE_01.yaml
metadata: name: MODBUS_DEVICE_01.yaml labels: ["MODBUS"] Description: This profile is for Modbus device 01 version: 1.0.1 UpdateData: 2020-01-08-14:25:30 Sensor: Temperature: Params: Address: 0 # Address Length: 1 DataType: int16 DataFormat: ABCD Info: v: -1 asm: r # Access Right: r, w, rw min: -10 # Minimum Value max: 100 # Maximum Value u: "celsius" # Unit Humidity: Params: Address: 1 Length: 1 DataType: int16 DataFormat: ABCD Info: v: -1 asm: r # Access Right: r, w, rw min: -100 # Minimum Value max: 100 # Maximum Value u: "percent" # Unit
2. Sensor Configuration for Device-2: <Install_folder>\config\industry\Profile\MODBUS_DEVICE_02.yaml
metadata: name: MODBUS_DEVICE_02.yaml labels: ["MODBUS"] Description: This profile is for Modbus device 02 version: 1.0.1 UpdateData: 2020-01-08-14:25:30 Sensor: X-Axis: Params: Address: 0 # Address Length: 1 DataType: int16 DataFormat: ABCD Info: v: -1 asm: r # Access Right: r, w, rw min: -10 # Minimum Value max: 100 # Maximum Value u: "mm" # Unit Y-Axis: Params: Address: 1 Length: 1 DataType: int16 DataFormat: ABCD Info: v: -1 asm: r # Access Right: r, w, rw min: -100 # Minimum Value max: 100 # Maximum Value u: "mm" # Unit
Demonstration
1. Open Modbus Simulator: ModSim32 and click "New" in program menu to create a new simulator page.
2. Set parameter as below:
- Device Id: 1
- Address: 0001
- Length: 2
- Modbus Point Type: HOLDING REGISTER
3. Enable Auto Simulation:
- Double click on the sensor address 40001
- Click "Auto Simulation"
4. Set simulation parameters:
- Check "Enable"
- Simulation Type: Increment
- Change Interval (secs): 5
- Step VAlue: 1
- Low Limit: 10
- High Limit: 20
5. Do the same step for the address 40002 and set simulation parameter as below:
- Simulation Type: Increment
- Low Limit: 60
- High Limit: 80