Difference between revisions of "AIR 030 Development"

Revision as of 06:32, 19 October 2022

Flash Image

Extract image

$ tar -zxvf air030_image_XXXXXX.tar.gz

Flash image

$ cd bootloader
$ sudo -s
# source flashcmd.txt

Tools

Flash Mac

Check All Intel-226 Module in PCI bus, The BDF(bus number/device number/function number) value will be first column.

ubuntu@localhost:~$ lspci
0004:00:00.0 PCI bridge: NVIDIA Corporation Device 229c (rev a1)
0004:01:00.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:00.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:06.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:0e.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:04:00.0 Ethernet controller: Intel Corporation Device 15f2 (rev 03)
0004:05:00.0 Ethernet controller: Intel Corporation Device 15f2 (rev 03)

Check NIC value with EepromAccessTool tool.

ubuntu@localhost:~$ ./EepromAccessTool
Intel(R) EEPROM Access Tool NVM/OTP Programming Example Tool   Version 0.8.0
Provided under the terms of a CNDA.  Do Not Distribute.
Copyright(C) 2017-2020 by Intel(R) Corporation
NIC     BUS     DEV     FUN     Silicon Memory Type Present
===     ===     ===     ===     =====   ======================
Check Command open to write error
 1      4        0       0      I225         FLASH
Check Command open to write error
 2      5        0       0      I225         FLASH

Flash Mac Address To get -nic value and BDF value please using above method.

$ sudo -s
# setpci -s 0004:04:00.0 COMMAND=0007
# ./EepromAccessTool -nic=1 -f=FXVL_15F2_LM_2MB_ARK_1.82_D.bin -mac=D4E5F6123456

The other Intel-I226

#setpci -s 0004:05:00.0 COMMAND=0007 
#./EepromAccessTool -nic=2 -f=FXVL_15F2_LM_2MB_ARK_1.82_D.bin -mac=D4E5F6123457 

Please do cold reboot after flash mac address.

How to check whether the flash proccess is success or not

• lspci command - If it is 0x125f value, it failed.
• ifconfig -a - Check the nerwork interface is available. ex: eth0, eth1 and so on.

Boot On Off

The boot count message will be printed before log-in.

Reset the boot count please remove bootCount.tt.

$ rm bootCount.tt

Module

AW-CB375NF(EWM-W159M201E)
Adjust dip switch

• LAN3_MKE_SW1 - SW1 : ON
• UART5_SW1 - SW1 : OFF

Wi-Fi
Start interface

$ sudo ifconfig wlan0 up

$ Scan AP

$ sudo iw dev wlan0 scan ap-force

Bluetooth

$ bluetoothctl
[bluetooth]# agent on
[bluetooth]# scan on

AW-CB511NF
Adjust dip switch

• LAN3_MKE_SW1 - SW1 : ON
• UART5_SW2 - SW1 : OFF

Wi-Fi
Start interface

$ sudo ifconfig wlan0 up

$ Scan AP

$ sudo iw dev wlan0 scan ap-force

Bluetooth

$ sudo -s
# hciattach /dev/ttyTHS1 bcm43xx 3000000 flow -t 20
# bluetoothctl
[bluetooth]# agent on
[bluetooth]# scan on

Image

The test image is available HERE. The 1st and 2nd image is only available for AGX-ORIN devkit.