Difference between revisions of "IoTGateway/Features/Linux/Peripheral"

Revision as of 09:49, 10 August 2016 (view source) Winston.huang (talk | contribs) m (Winston.huang moved page IoTGateway/BSP/Linux/iMX6/Features/Peripheral to IoTGateway/Features/Linux/Peripheral without leaving a redirect) ← Older edit		Revision as of 03:51, 11 August 2016 (view source) Winston.huang (talk | contribs) Newer edit →
Line 1:		Line 1:
−	{| class="wikitable"
−	|-
−	! Feature !! Description
−	|-
−	| ADC ||
−	|-
−	| Backlight||
−	|-
−	| Camera ||
−	|-
−	| CAN Bus||
−	|-
−	| CPU Frequency||
−	|-
−	| Ethernet||
−	|-
−	| Framebuffer||
−	|-
−	| GPIO||
−	|-
−	| I2C||
−	|-
−	| SPWG/JEDIA||
−	|-
−	| One Wire||
−	|-
−	| RTC||
−	|-
−	| SATA||
−	|-
−	| SD/MMC||
−	|-
−	| SPI||
−	|-
−	| UART||
−	|-
−	| USB||
−	|-
−	| Watchdog||
−	|-
−	| IR||
−	|}
	==ADC==		==ADC==
	analogue to digital converters		analogue to digital converters

---

Revision as of 03:51, 11 August 2016

ADC

analogue to digital converters

Backlight

Enable/read and modify backlight brightness

Camera

Example

CAN Bus

Prerequisites

Testing

Connect can0 and can1

<CAN1_D+> connect to <CAN2_D+>

<CAN1_D-> connect to <CAN2_D->

Configure

# ip link set can0 up type can bitrate 125000

# ip link set can1 up type can bitrate 125000

Command

Test 1

# candump can1 &

# cansend can0 12345678#123412341234

The following shows the result

can1 12345678 [6] 12 34 12 34 12 34

Test 2

# cansend can0 133#ababdede

The following shows the result

can1 133 [4] AB AB DE DE

CPU Frequency

Prerequisites

Testing

Ethernet

Example

Framebuffer

Example

GPIO

Example

I2C

Example

SPWG/JEDIA

Standard Panels Working Group (SPWG)

Japan Electronic Industry Development Association (JEIDA)

How to setting SPWG/JEIDA mode in RISC?

Modify Register GPR(IOMUXC_GPR2)value

Address : 0x020E0008(h)

BIT6 and BIT8 set "0" (SPWG)

BIT6 and BIT8 set "1" (JEIDA)

One Wire

Example

RTC

Example

SATA

Example

SD/MMC

Example

SPI

Example

UART

Example

USB

Example

Watchdog

Example

IR

To decode the infrared signals and provide an uniform interface

lircd -d /dev/lirc0

used parameters:

-d --device=device    read from given device
-u --uinput           generate Linux input events

Executes commands on an IR signal decoded by lircd,

irexec -d /devlirc0

Note: if show these message after running lircd

lircd: can't open or create /var/run/lirc/lircd.pid
lircd: No such file or directory

It has to add the "/var/run/lirc" folder

mkdir /var/run/lirc

How to debug:

1. To check that signals are decoded correctly

mode2 -d /dev/lirc0

It repeats to show "space" and "pulse" while clicking a control button

space 8451531
pulse 476

2. To check input events.

First, It must add the parameter,"-u", in lircd command

lircd -d /dev/lirc0 -u

It will register at inputX,

input: lircd as /devices/virtual/input/input1 

Run evtest to check events

evtest -d /dev/input/event1