Difference between revisions of "IoTGateway/Features/Linux/Peripheral"
Daniel.hung (talk | contribs) |
Daniel.hung (talk | contribs) |
||
| Line 1: | Line 1: | ||
{{DISPLAYTITLE:Linux Peripheral Features}} | {{DISPLAYTITLE:Linux Peripheral Features}} | ||
| − | + | ||
| − | |||
| − | |||
==ADC== | ==ADC== | ||
analogue to digital converters | analogue to digital converters | ||
| Line 86: | Line 84: | ||
Run evtest to check events | Run evtest to check events | ||
evtest -d /dev/input/event1 | evtest -d /dev/input/event1 | ||
| + | |||
| + | ==One Wire== | ||
| + | Example | ||
| + | |||
| + | ==RTC== | ||
| + | Example | ||
| + | |||
| + | ==SATA== | ||
| + | Example | ||
| + | |||
| + | ==SD/MMC== | ||
| + | Example | ||
| + | |||
| + | ==SPI== | ||
| + | Example | ||
==SPWG/JEDIA== | ==SPWG/JEDIA== | ||
| Line 104: | Line 117: | ||
:[[Image:JEIDA1.png|350px]] | :[[Image:JEIDA1.png|350px]] | ||
:[[Image:JEIDA2.png|350px]] | :[[Image:JEIDA2.png|350px]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==UART== | ==UART== | ||
Revision as of 04:46, 11 August 2016
Contents
ADC
analogue to digital converters
Backlight
Enable/read and modify backlight brightness
Camera
Example
CAN Bus
Prerequisites
Testing
- Connect can0 and can1
- <CAN1_D+> connect to <CAN2_D+>
- <CAN1_D-> connect to <CAN2_D->
- Configure
-
# ip link set can0 up type can bitrate 125000 -
# ip link set can1 up type can bitrate 125000
- Command
- Test 1
# candump can1 &# cansend can0 12345678#123412341234- The following shows the result
-
can1 12345678 [6] 12 34 12 34 12 34
- Test 2
# cansend can0 133#ababdede- The following shows the result
-
can1 133 [4] AB AB DE DE
- Test 2
CPU Frequency
Prerequisites
Testing
Ethernet
Example
Framebuffer
Example
GPIO
Example
I2C
Example
IR
To decode the infrared signals and provide an uniform interface
lircd -d /dev/lirc0
used parameters:
-d --device=device read from given device -u --uinput generate Linux input events
Executes commands on an IR signal decoded by lircd,
irexec -d /devlirc0
Note: if show these message after running lircd
lircd: can't open or create /var/run/lirc/lircd.pid lircd: No such file or directory
It has to add the "/var/run/lirc" folder
mkdir /var/run/lirc
How to debug:
1. To check that signals are decoded correctly
mode2 -d /dev/lirc0
It repeats to show "space" and "pulse" while clicking a control button
space 8451531 pulse 476
2. To check input events.
First, It must add the parameter,"-u", in lircd command
lircd -d /dev/lirc0 -u
It will register at inputX,
input: lircd as /devices/virtual/input/input1
Run evtest to check events
evtest -d /dev/input/event1
One Wire
Example
RTC
Example
SATA
Example
SD/MMC
Example
SPI
Example
SPWG/JEDIA
Standard Panels Working Group (SPWG)
Japan Electronic Industry Development Association (JEIDA)
How to setting SPWG/JEIDA mode in RISC?
Modify Register GPR(IOMUXC_GPR2)value
Address : 0x020E0008(h)
BIT6 and BIT8 set "0" (SPWG)
BIT6 and BIT8 set "1" (JEIDA)
UART
Example
USB
Example
Watchdog
Example