Difference between revisions of "ROM-3620 user guide"
Jems.cheng (talk | contribs) |
Jems.cheng (talk | contribs) |
||
Line 345: | Line 345: | ||
= '''快速入门 (Quick Start)''' = | = '''快速入门 (Quick Start)''' = | ||
+ | |||
Line 395: | Line 396: | ||
| QE test | | QE test | ||
|} | |} | ||
− | + | ||
---- | ---- | ||
− | |||
− | |||
− | |||
− | |||
=== '''Linux 燒錄方法 (Linux Flash eMMC Method)''' === | === '''Linux 燒錄方法 (Linux Flash eMMC Method)''' === |
Revision as of 04:29, 29 December 2023
Contents
- 1 產品介紹(Product introduction)
- 2 硬件接口說明(Hardware interface introduction)
- 3 快速入门 (Quick Start)
- 4 Linux系统的基本使用(Linux System Basic Operating Method)
- 4.1 UUU 使用方法(USB Connection (OTG port))
- 4.2 Display Setting (ROM-5620)
- 4.3 乙太網路使用方法(Ethernent Testing Method)
- 4.4 WiFi使用方法(WIFI Testing Method)
- 4.5 4G使用方法(4G Testing Method)
- 4.6 GPIO使用方法(GPIO Operating Method)
- 4.7 串口使用方法(Serial Port Operating Method)
- 4.8 蓝牙使用方法(BlueTooth Operating Method)
- 4.9 遠程訪問及文件傳輸(Remote Access and File Transimmion)
- 5 通用方法(General Method)
- 6 Linux BSP編譯方法(Linux BSP Compile Method)
產品介紹(Product introduction)
產品特性(Product Features)
- NXP i.MX 8X processor with 2-4 x Arm Cortex-A35 cores
- Onbard LPDDR4 memory and eMMC 16GB
- Supports wide range power input 5V~24V
- Supports Vivante GC7000 Lite hardware accelerators
- Supports Ultra HD 4K/ full HD 1080p video decode and HD 1080p video encode hardware engine
- Supports 1 PCIe, 1 USB 3.0, 1 USB 2.0, 1 USB OTG2.0, 5 I2C, 1 I2S, 1 Camera in, 2 CANbus, 10 GPIO
- Low power consumption, fanless desgin
- Supports Linux and Android BSP
產品官網連結(Product Features)
硬件接口說明(Hardware interface introduction)
接口布局和尺寸(Layout and Sizes)
ROM-3620 接口布局圖 Board Dimension Layout
Position |
Description |
SW1(1) |
UART & Debug Port selection |
SW1(2) |
AT & ATX mode selection |
SW1(1): UART & Debug Port selection
Setting |
Function |
1-On |
Normal UART |
1-Off |
Debug Console (Default) |
SW1(2): AT/ATX Mode Selection
Setting |
Function |
2-On |
AT Mode (Default) |
2-Off |
ATX Mode |
ROM-DB3900 接口布局圖 Board Dimension Layout
主板内置插针式引脚排序方式 (Pin Header defination)
Internal I/O
Position | Description | Connector Type |
DCIN | DC-in | DC POWER JACK 2.5mm 90D(M) DIP 2DCG213B200 |
COM01 | COM Port | D-SUB Conn. 18P 90D(M) DIP DM10151-H531-4F |
HDMI | HDMI | HDMI Conn. 19P 0.5mm 90D(F) SMD QJ51191-LFB4-7F |
VGA | VGA | D-SUB Conn. 15P 90D(F) DIP 070242FR015S200ZU |
RJ45+USB | LAN+USB | PhoneJack RJ45+USB3.0*2 32P 90D(F) DIP 05-A00919 |
Phone Jack | Phone Jack | Audio Jack 9P 2.5mm 90D(F) DIP ABA-JAK-03 |
Audio | Audio | PIN HEADER 2x10P 2.54mm 180D(M) DIP 21N22564 |
LVDS | LVDS | B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V(91) |
FAN | FAN | Wafer 2.54mm 3P 180D(M) DIP 22-27-2031 |
SATA_PWR | SATA power | WAFER 4P 2.5mm 180D(M) DIP 24W1161-04S10-01T |
PCIE_SLOT0 | PCIE_SLOT0 | PCIEXPRESS 36P 180D(F) DIP 2EG01817-D2D-DF |
PCIE_SLOT1 | PCIE_SLOT1 | PCIEXPRESS 36P 180D(F) DIP 2EG01817-D2D-DF |
SATA | SATA | Serial ATA 7P 1.27mm 180D(M) DIP WATM-07DBN4A3B8 |
GPIO | GPIO | PIN HEADER 10x2P 2.0mm 180D(M) DIP 21N22050 |
LVDS_BKLT | LVDS Backlight | WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIHVEI |
SW3 | Reset button | TACT SW STS-091 SMD 4P H=3.8mm |
SW4 | Power button | TACT SW STS-091 SMD 4P H=3.8mm |
SW5 | Sleep button | TACT SW STS-091 SMD 4P H=3.8mm |
SW6 | Wake up button | TACT SW STS-091 SMD 4P H=3.8mm |
SPI0 | SPI0 | PIN HEADER 2x4P 2.54mm 180D(M) DIP 210-92-04GB02 |
SPI1 | SPI1 | PIN HEADER 2x4P 2.54mm 180D(M) DIP 210-92-04GB02 |
SW2 | Boot selection | DIP SW EDG104S DIP 6P Radial SPST |
COM3 | COM3 | BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10 |
COM2 | COM2 | BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10 |
CAN1 | CAN1 | BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10 |
CAN0 | CAN0 | BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10 |
USB_OTG | USB OTG | MINI USB 5P 180D(F) SMD UH51543-CS7-7F |
SD | SD | SD CARD 9P 90D(F) SMD WK2192C-S3D-7H |
System_Bus | SYSTEMBUS | PCB SKT 30x4P 2.00mm 180D(F) DIP 264-40303-02 |
I2C0 | I2C0 | WAFER BOX 2.0mm 4P 180D(M) W/LOCKA2001WV2-4P |
I2C1 | I2C1 | WAFER BOX 2.0mm 4P 180D(M) W/LOCKA2001WV2-4P |
RTXA,RTXB, RTXC,RTXD |
RTX B2B Connector |
B/B Conn. 50x2P 0.5mm 180D(M) SMDAXK500137YG |
Rear I/O
Position | Description | Name |
DCIN | DC Jack | A |
COM01A | UART Port 1 | B |
COM01B | UART Port 2 | C |
HDMI | HDMI Port | D |
VGA | VGA Port | E |
RJ45+USB | GbE Ethernet Connector | F |
RJ45+USB | USB Port 1/ 2 | G |
PHONE_JACK | MIC Input/ Audio Output | H |
接口引脚定義 (Pin definitions)
Rear IO:
- DCIN
- 串口(COM01A、UART1、4_WIRE(ttyLP1))
- 串口(COM01B、UART2、4_WIRE(ttyLP2))
- 显示接口(VGA、HDMI)
- RJ45+USB接口(RJ45、USB1-2)
- PHONE_JACK接口(Audio_output)
Internel IO:
- Boot_selection_switch
- 電池(BAT1)
- CAN(CAN0,CAN1)
- LVDS接口(LVDS、LVDS_BKLT)
- 串口(COM3(COM_DB(ttyLP0))、COM2(UART3)(ttyLP3))
- USB_OTG接口(USB_OTG)
- I2S0接口(I2S\Audio_Codec)
- 电源及指示灯和开关机复位按钮(Power 、LED、Power Button、Reset Button、Sleep Button)
- GPIO接口
- PCIE接口_SATA接口_SPI、I2C_接口
机械尺寸 (Mechanical Characteristics)
ROM-3620
快速入门 (Quick Start)
系统下载 (OS Download)
- 'Linux系统 (Linux OS)'
Version | Date | Product | CPU | Yocto3.0/Ubuntu18.04/Debian9 | SDK | Components | Features | Modules | Test Report | Release | Release notes | Comment |
V90210 | 2021-03-09 | ROM-3620 | 8X | Yocto2.5 | SDK | Components | Features | Modules | Test Report | 4.14.98 MP | Release Note | MP |
VA0297 | 2021-07-21 | ROM-3620 | 8X | Yocto3.0 | SDK | Components | Features | Modules | Test Report | 5.4.70 Alpha | Release_Note | QE test |
Linux 燒錄方法 (Linux Flash eMMC Method)
使用Flash tool 燒錄鏡像到eMMC (Flash image into eMMC by Flash Tools)
1. Copy 3620A1AIM20LIV90210_iMX8X_flash_tool.tgz package to your desktop.
2. Insert SD card to PC.
3. Make a bootable sd card.
# cd 3620A1AIM20LIV90210_iMX8X_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/sdg
4. Insert SD card and copy 3620A1AIM20LIV90210_iMX8X_flash_tool to USB disk.
5. Insert USB disk and SD card then Boot from SD.
6. Enter usb disk folder, make a bootable emmc.
# cd 3620A1AIM20LIV90210_iMX8X_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/mmcblk0
使用UUU工具燒錄鏡像到eMMC (Flash image into eMMC by UUU Tools)
1. Download UUU tool from (https://github.com/ADVANTECH-Corp/uuu/releases/download/v20191101/uuu).
2. Create a folder with files as below:
imx-boot-imx8qxprom3620a1-sd.bin-flash
fsl-image-qt5-validation-imx-imx8qxprom3620a1-20210309105548.rootfs.sdcard
3. Connect otg cable from PC to device.
4. Set the correct boot mode, then power on(4-on only).
5. Perform the following command:
6. UUU tool will start recovery image to eMMC.
7. For more usage:
http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#System_Recovery
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Check the Sriel port in Device Manager (查看PC端的串口号):
if you can not identify the Serial device , please check your serial driver.
Debug port connection (串口連接)
Log into Terminal Tool (进入串口调试终端):
Linux系统的基本使用(Linux System Basic Operating Method)
UUU 使用方法(USB Connection (OTG port))
Display Setting (ROM-5620)
U-boot Command :
setenv fdt_file xxxx.dtb
env save
boot
- Display: Default support g070vw01 LVDS panel on LVDS1
- LVDS
- g070vw01(LVDS1)
- adv-imx8mxp-rom5620-a1.dtb
- g150xgel05
- adv-imx8qxp-rom5620-a1-lvds-chimei.dtb
- g215hvn01
- adv-imx8qxp-rom5620-a1-lvds-dual.dtb
- g070vw01(LVDS1)
- LVDS to HDMI(LVDS1)
- adv-imx8qxp-rom5620-a1-hdmi-bridge.dtb
- DSI to HDMI(LVDS1)
- adv-imx8qxp-rom5620-a1-hdmi-bridge.dtb
- DSI
- auog101uan02
- adv-imx8qxp-rom5620-a1-auog101uan02.dtb
- auog101uan02
- LVDS
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
Command: Ping - I eth1 8.8.8.8 or Ping - I eth0 8.8.8.8
WiFi使用方法(WIFI Testing Method)
Command : # killall wpa_supplicant # ifconfig wlan0 up # wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf # wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf # udhcpc -b -i wlan0''' ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
4G使用方法(4G Testing Method)
Command: Test 4G: (EWM-C117FL06E - USB) Step 1: Connect EWM-C117FL06E to Mini PCIE slot on 9680015491 and connect the card to CN6 PCIe_D slot on ROM-DB5901. Step 2: Connect the antenna 1750007990-01 to the SMA (F) connector on 9680015491 and connect the IPEX connector to MT1 on EWM-C117FL06E module. Step 3: Connect the Mini USB cable from 9680015491 to USB 2.0 Type A port on ROM-DB5901. Step 4: Power on and execute the pppd command to connect to the network.
GPIO使用方法(GPIO Operating Method)
Loop-back Test (Take GPIO4 and GPIO5 as examples) Step 1: Connect GPIO4 and GPIO5 Step 2: Export GPIO interface root@imx8qxprom5620a1 : ~# echo 456 > /sys/class/gpio/export root@imx8qxprom5620a1 : ~# echo 452 > /sys/class/gpio/export Step 3: Set direction root@imx8qxprom5620a1 : ~# echo out > /sys/class/gpio/gpio1/direction root@imx8qxprom5620a1 : ~# echo in > /sys/class/gpio/gpio2/direction Step 4: Read value and set output value then check root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 0r oot@imx8qxprom5620a1 : ~# echo 1 > /sys/class/gpio/gpio1/value root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 1
串口使用方法(Serial Port Operating Method)
RS-232 Test
SER1_UART2: /dev/ttyLP2: COM1
SER3_UART0: /dev/ttyLP0: COM3
SW6/7 Setting (SW6/7設置)
RS232: 1:on 2:off
RS422: 1:on 2:on
RS485: 1:off 2:on
COM0 (CN15A): UART1 test
Loopback Test (eg. ttyLP1)
UART 1: Change SW7 jumper to switch modes. (1ON 2OFF: RS-232)
UART 1: Change CN27~CN30 jumper to (1-2 short)
# stty -F /dev/ttyLP1 -echo -onlcr 115200 # cat /dev/ttyLP1 & # echo test > /dev/ttyLP1
蓝牙使用方法(BlueTooth Operating Method)
Command : $ hciconfig hci0 up $ bluetoothctl $ discoverable on $ pairable on $ scan on [NEW] FC:18:3C:8D:75:F4 myphone $ scan off $ pair FC:18:3C:8D:75:F4 $ connect FC:18:3C:8D:75:F4
遠程訪問及文件傳輸(Remote Access and File Transimmion)
查看主板IP位址 ( Chech IP Address ):
Command : ifconfig
Windows下SSH访问及文件传输
SSH Remote Log into Device
- SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
- 需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600 # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°
查看CPU频率(Check CPU Frequency)
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq >> 900000 cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq >> 1200000
查看内存容量(Check Memory Capacity)
root@imx8qxprom5620a1:/# busybox free -m total used free shared buffers cached Mem: 1794920 516080 1278840 17252 9852 80292 -/+ buffers/cache: 425936 1368984 Swap: 0 0 0
查看存储容量(Check Storage Capacity)
root@imx8qxprom5620a1:/# busybox df -h Filesystem Size Used Available Use% Mounted on /dev/root 13.4G 1.7G 11.1G 13% / devtmpfs 395.8M 4.0K 395.8M 0% /dev tmpfs 876.4M 0 876.4M 0% /dev/shm tmpfs 876.4M 16.5M 859.9M 2% /run tmpfs 876.4M 0 876.4M 0% /sys/fs/cgroup tmpfs 876.4M 4.0K 876.4M 0% /tmp tmpfs 876.4M 280.0K 876.2M 0% /var/volatile /dev/mmcblk0p2 13.6G 1.7G 11.3G 13% /run/media/mmcblk0p2 /dev/mmcblk0p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk0p1 /dev/mmcblk1p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk1p1 tmpfs 175.3M 88.0K 175.2M 0% /run/user/0 root@imx8qxprom5620a1:/#
網路Ping測試(Ping Network Testing)
ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
設置RTC (RTC Setting)
root@imx8qxprom5620a1:/# systemctl stop ntpdate.service root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date Wed Sep 8 16:07:00 UTC 2021 Wed Sep 8 16:07:00 UTC 2021 root@imx8qxprom5620a1:/# date Wed Sep 8 16:07:06 UTC 2021 root@imx8qxprom5620a1:/#'''
Linux BSP編譯方法(Linux BSP Compile Method)
Yocto 3.0
如果有驗證上的錯誤 請使用以下的方法
### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none
============================================================
export GIT_SSL_NO_VERIFY=1
#or
git config --global http.sslverify false
============================================================