Difference between revisions of "EPC-R3710 user guide"
(6 intermediate revisions by the same user not shown) | |||
Line 15: | Line 15: | ||
=== '''產品官網連結(Product Features) ''' === | === '''產品官網連結(Product Features) ''' === | ||
− | '''EPC-R3710''' | + | [https://www.advantech.com/en/search/?q=EPC-R3710&st=support&from=support '''EPC-R3710'''] |
== '''硬件接口說明(Hardware interface introduction)''' == | == '''硬件接口說明(Hardware interface introduction)''' == | ||
Line 549: | Line 549: | ||
== '''通用方法(General Method)''' == | == '''通用方法(General Method)''' == | ||
− | === | + | === '''查看CPU温度(Check CPU Temperature)''' === |
<pre> root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 40000 | <pre> root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 40000 | ||
# 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]&deg; &gt;&gt;&gt; 40&deg;</pre> | # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]&deg; &gt;&gt;&gt; 40&deg;</pre> | ||
− | === ''' | + | === '''查看CPU频率(Check CPU Frequency)''' === |
<pre> cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq | <pre> cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq | ||
&gt;&gt; 1200000 | &gt;&gt; 1200000 | ||
Line 560: | Line 560: | ||
&gt;&gt; 1800000</pre> | &gt;&gt; 1800000</pre> | ||
− | === ''' | + | === ''' 查看内存容量(Check Memory Capacity)''' === |
<pre>root@linaro-alip:~# busybox free -m | <pre>root@linaro-alip:~# busybox free -m | ||
&amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; total &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;used &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;free &amp;nbsp; &amp;nbsp; &amp;nbsp;shared &amp;nbsp;buff/cache &amp;nbsp; available | &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; total &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;used &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;free &amp;nbsp; &amp;nbsp; &amp;nbsp;shared &amp;nbsp;buff/cache &amp;nbsp; available | ||
Line 568: | Line 568: | ||
</pre> | </pre> | ||
− | === ''' | + | === ''' 查看存储容量(Check Storage Capacity)''' === |
<pre>root@linaro-alip:~# busybox df -h | <pre>root@linaro-alip:~# busybox df -h | ||
Filesystem &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;Size &amp;nbsp; &amp;nbsp; &amp;nbsp;Used Available Use% Mounted on | Filesystem &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp; &amp;nbsp;Size &amp;nbsp; &amp;nbsp; &amp;nbsp;Used Available Use% Mounted on | ||
Line 583: | Line 583: | ||
root@linaro-alip:~#</pre> | root@linaro-alip:~#</pre> | ||
− | === ''' | + | === '''網路Ping測試(Ping Network Testing)''' === |
<pre> ping 8.8.8.8 | <pre> ping 8.8.8.8 | ||
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. | PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. | ||
Line 603: | Line 603: | ||
== '''Android BSP編譯方法(Android BSP Compile Method)''' == | == '''Android BSP編譯方法(Android BSP Compile Method)''' == | ||
− | + | *[[Android_BSP_User_Guide_for_rk3399_series_10.0|Android BSP User Guide for rk3399 series 10.0]] | |
− | |||
− | |||
− | + | '''Debian BSP 編譯方式( Debian BSP Compile Method) ''' | |
− | + | *[https://ess-wiki.advantech.com.tw/view/Debian_BSP_User_Guide_for_rk3399_risc_series Debian_BSP_User_Guide_for_rk3399_risc_series] | |
| | ||
− | #<u>'''or'''</u> | + | '''如果有驗證上的錯誤 請使用以下的方法(If you got " Server certificate verification failed " message ,please follow the solution as below) ''' |
+ | |||
+ | <u>'''### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none<br/> ============================================================<br/> export GIT_SSL_NO_VERIFY=1'''</u> | ||
+ | |||
+ | <u>'''or'''</u> | ||
<u>'''git config --global http.sslverify false<br/> ============================================================'''</u> | <u>'''git config --global http.sslverify false<br/> ============================================================'''</u> |
Latest revision as of 02:46, 18 April 2024
Contents
- 1 產品介紹(Product introduction )
- 2 硬件接口說明(Hardware interface introduction)
- 3 接口布局和尺寸(Layout and Sizes)
- 4 Connector List
- 5 快速入门 (Quick Start)
- 6 Android 燒錄方法 (Android Flash eMMC Method)
- 7 Linux 燒錄方法 (Linux Flash eMMC Method)
- 8 系统的基本使用(Linux System Basic Operating Method)
- 9 通用方法(General Method)
- 10 Android BSP編譯方法(Android BSP Compile Method)
產品介紹(Product introduction )
產品特性(Product Features)
- Rockchip Arm® Cortex®-A72 RK3399 up to 1.8 GHz
- Onboard LPDDR4 2GB
- HDMI 1920x1080 at 60Hz, 1 Dual Channel 24 bit LVDS
- 1 2-wire RS-232, 1 USB3.0, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
- 1 mini-PCIe for 3G/4G
- UIO expansion 3 USB2.0, 8 GPIO, 2 RS232 2/2-wires UART, 1 I2C
- Supports Debian9/10 and Android7.1/10.0
- Support I/O Expansions by UIO40-Express I/O boards, please refer to page #3 for more information
產品官網連結(Product Features)
硬件接口說明(Hardware interface introduction)
接口布局和尺寸(Layout and Sizes)
接口布局圖 Board Dimension Layout
Connector List
BAT | RTC Battery Connector |
HDMI | HDMI1 CONN |
BLP2 | LVDS BKL PWR 12V select |
LVDS/eDP LVDS BKL |
LVDS DATA/PWRCONN |
LAN1 | LAN |
LAN2 | LAN |
MINIPCIE | MINI PCIE 52P |
SIM | Nano SIM Card |
AUDIO | Audio PIN Header |
USB1 | USB CONN |
COM2/Debug | COM2 |
SD | SD Slot |
OTG | USB |
BTN | MASKROM mode pin header |
RST | Reset Button |
DCIN1 | 12V DC Jack |
LED | LED |
CN11 | UIO1 |
CN12 | UIO2 |
接口引脚定義 (Pin definitions)
机械尺寸 (Mechanical Characteristics)
快速入门 (Quick Start)
系统下载 (OS Download)
- Android 系统 (Android OS)
Android 10 : AIM-Linux/BSP/RK/Linux_Android_OS_Release_note/Android10/
Android 7 : AIM-Linux/BSP/RK/Linux_Android_OS_Release_note/Android7/
- Debian 系統( Debian OS)
Debbian 10:AIM-Linux/BSP/RK/Linux_Debian_OS_Release_note/Debian10/
Android 燒錄方法 (Android Flash eMMC Method)
1. 請先準備一條 mirco USB 線材 和 Debug Cable
mirco USB
Debug Cable
2. 插入 RSB-3710 的OTG port
連接 Debug cable
2. 設定終端機(Set Debug Terminal)
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 &nbsp; Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Note:
Check the Sriel port in Device Manager (查看PC端的串口号):
if you can not identify the Serial device , please check your serial driver.
3.打開燒錄軟體
4. 打開電源
5. 在終端機上可看到Debug 訊息, 按下"Ctrl + C" 組合鍵. 進入u-boot
6. 在u-boot ,輸入"loader" 可進入燒錄模式 , Android tool 會同時顯示 "Found One MASKROM Device "
7. 在RKDevTool 按下 "Run" ,可進行燒錄.
8. 燒錄完畢
9. 重新拔插電源, 讓RSB-3710 重新開機 ,接上HDMI ,可顯示安卓的桌面.
Linux 燒錄方法 (Linux Flash eMMC Method)
1. 請先準備一條 mirco USB 線材 和 Debug Cable
mirco USB
Debug Cable
2. 插入 RSB-3710 的OTG port
連接 Debug cable
3. 設定終端機(Set Debug Terminal)
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 &amp;nbsp; Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Note:
查看PC端的串口号(Check the Sriel port in Device Manager) :
如果沒有找到 請先確認是否有安裝驅動(if you can not identify the Serial device , please check your serial driver.)
3.打開燒錄軟體
4. 打開電源
5. 在終端機上可看到Debug 訊息, 按下"Ctrl + C" 組合鍵. 進入u-boot
6. 在u-boot ,輸入"rbrom " 可進入燒錄模式 , Android tool 會同時顯示 "Found One MASKROM Device "
7. 清除後,重新上電,會直接進入 "Found One MASKROM Device" 燒錄模式
8. 在RKDevTool 按下 "Run" ,可進行燒錄.
9. 燒錄完畢
10. 重新拔插電源, 讓RSB-3710 重新開機 ,接上HDMI ,可顯示Debian的桌面.
系统的基本使用(Linux System Basic Operating Method)
Display Setting (RSB-3710)
lvds | lvds-g070vw01; lvds-g150xgel05; lvds-g215hvn01 |
hdmi | hdmi-default |
dp | dp-default |
IN uboot | In Debian/Android |
setenv prmry_screen hdmi-default | fw_setenv prmry_screen hdmi-default |
setenv extend_screen edp-1920x1080 | fw_setenv extend_screen edp-1920x1080 |
saveenv | |
reset | reboot |
In u-boot:
=> setenv prmry_screen lvds-g070vw01
=> setenv extend_screen hdmi-default
=> saveenv
=> reset
In Linux:
~# fw_setenv prmry_screen lvds-g070vw01
~# reboot
Modify LVDS backlight PWM: (Defaul is 20KHz, New version BSP support to modify the PWM clock in u-boot from 200~20KHz)
In u-boot:
=> setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)
In Linux:
~# fw_setenv lvds_pwm_clock 10000 (Set PWM clock to 10KHz)
~# reboot
Check PWM duty sysle in Linux:
~# cat /sys/kernel/debug/pwm
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
Command: Ping 8.8.8.8
WiFi使用方法(WIFI Testing Method)
# killall wpa_supplicant # ifconfig wlan0 up # wpa_passphrase &quot;SSID&quot; &quot;PASSWORD&quot; &gt; /tmp/wpa.conf # cat /tmp/wpa.conf # wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf # udhcpc -b -i wlan0 # ifconfig # ping 8.8.8.8 Add DNS to /etc/resolv.conf # cat /etc/resolv.conf # Generated by Connection Manager nameserver 8.8.8.8 nameserver 8.8.4.4 Now can ping google.com # ping google.com
4G使用方法(4G Testing Method)
GPIO使用方法(GPIO Operating Method)
蓝牙使用方法(BlueTooth Operating Method)
# hciattach /dev/ttymxc0 bcm43xx 115200 flow # hciconfig hci0 up # hcitool scan# bluetoothctl # discoverable on #pairable on # scan on # scan off # pair 84:C5:A6:D3:AF:E4 # connect 84:C5:A6:D3:AF:E4 Check BT connect info # info 84:C5:A6:D3:AF:E4
音訊使用方法(BlueTooth Operating Method)
Line-in , Line-out, MIC 1.Line-out Command&amp;nbsp;: gplay-1.0 2.MIC Command&amp;nbsp;: arecord Check audio codec: # cat /proc/asound/cards 0 [sgtl5000 ]: sgtl5000 - sgtl5000 sgtl5000 1 [audiohdmi ]: audio-hdmi - audio-hdmi audio-hdmi root@imx8mprsb3720a1:~# Set Mic/audio volume # amixer set Mic 100% # amixer set Lineout 100% # amixer set PCM 100% Record and playback Example command: # arecord &ndash;t wav &ndash;c 1 &ndash;r 44100 &ndash;d 5 /tmp/mic.wav # aplay /tmp/mic.wav Record from MIC: # arecord -D plughw:0,0 -r 16000 -f S16_LE ./f-16000.wav Recording WAVE &#39;./f-16000.wav&#39;&amp;nbsp;: Signed 16 bit Little Endian, Rate 16000 Hz, Mono # aplay f-16000.wav Playing WAVE &#39;f-16000.wav&#39;&amp;nbsp;: Signed 16 bit Little Endian, Rate 16000 Hz, Mono Play wav file from codec: # aplay -D plughw:0,0 file_example_WAV_10MG.wav Playing WAVE &#39;file_example_WAV_10MG.wav&#39;&amp;nbsp;: Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Play wav file from HDMI: # aplay -D plughw:1,0 file_exam ple_WAV_10MG.wav Playing WAVE &#39;file_example_WAV_10MG.wav&#39;&amp;nbsp;: Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
看門狗測試 (Watch Dog Test method)
System will reboot after 1 sec # /unit_tests/Watchdog/wdt_driver_test.out 1 2 0
遠程訪問及文件傳輸(Remote Access and File Transimmion)
查看主板IP位址 ( Chech IP Address ):
Command&amp;nbsp;: ifconfig
Windows下SSH访问及文件传输
SSH Remote Log into Device
- SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
- 需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
root@linaro-alip:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 40000 # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 40°
查看CPU频率(Check CPU Frequency)
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq >> 1200000 cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq >> 1800000
查看内存容量(Check Memory Capacity)
root@linaro-alip:~# busybox free -m &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; total &nbsp; &nbsp; &nbsp; &nbsp;used &nbsp; &nbsp; &nbsp; &nbsp;free &nbsp; &nbsp; &nbsp;shared &nbsp;buff/cache &nbsp; available Mem: &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 1961 &nbsp; &nbsp; &nbsp; &nbsp; 303 &nbsp; &nbsp; &nbsp; &nbsp;1096 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;97 &nbsp; &nbsp; &nbsp; &nbsp; 561 &nbsp; &nbsp; &nbsp; &nbsp;1575 Swap: &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0 root@linaro-alip:~#
查看存储容量(Check Storage Capacity)
root@linaro-alip:~# busybox df -h Filesystem &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Size &nbsp; &nbsp; &nbsp;Used Available Use% Mounted on /dev/root &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 7.8G &nbsp; &nbsp; &nbsp;2.8G &nbsp; &nbsp; &nbsp;4.6G &nbsp;37% / devtmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;972.3M &nbsp; &nbsp; &nbsp;8.0K &nbsp; &nbsp;972.3M &nbsp; 0% /dev tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 980.8M &nbsp; &nbsp; &nbsp; &nbsp; 0 &nbsp; &nbsp;980.8M &nbsp; 0% /dev/shm tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 980.8M &nbsp; &nbsp; 16.8M &nbsp; &nbsp;964.0M &nbsp; 2% /run tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 5.0M &nbsp; &nbsp; &nbsp;4.0K &nbsp; &nbsp; &nbsp;5.0M &nbsp; 0% /run/lock tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 980.8M &nbsp; &nbsp; &nbsp; &nbsp; 0 &nbsp; &nbsp;980.8M &nbsp; 0% /sys/fs/cgroup /dev/mmcblk1p10 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 6.4G &nbsp; &nbsp; &nbsp;3.8M &nbsp; &nbsp; &nbsp;6.4G &nbsp; 0% /userdata /dev/mmcblk1p7 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 62.6M &nbsp; &nbsp; 12.0M &nbsp; &nbsp; 47.3M &nbsp;20% /oem tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 196.2M &nbsp; &nbsp; &nbsp; &nbsp; 0 &nbsp; &nbsp;196.2M &nbsp; 0% /run/user/0 tmpfs &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 196.2M &nbsp; &nbsp; &nbsp;8.0K &nbsp; &nbsp;196.1M &nbsp; 0% /run/user/1000 root@linaro-alip:~#
網路Ping測試(Ping Network Testing)
ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
設置RTC (RTC Setting)
Set system time to current, then write to RTC
root@linaro-alip:~# date 01282022
Fri Jan 28 20:22:00 UTC 2022
root@linaro-alip:~#
Restart the RTC time to system time
- hwclock -s && date
root@linaro-alip:~# hwclock -s && date
Thu Jan 20 06:18:26 UTC 2022
root@linaro-alip:~#
Android BSP編譯方法(Android BSP Compile Method)
Debian BSP 編譯方式( Debian BSP Compile Method)
如果有驗證上的錯誤 請使用以下的方法(If you got " Server certificate verification failed " message ,please follow the solution as below)
### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none
============================================================
export GIT_SSL_NO_VERIFY=1
or
git config --global http.sslverify false
============================================================