Difference between revisions of "RSB-4411 user guide"
Jems.cheng (talk | contribs) |
Jems.cheng (talk | contribs) (→Linux BSP編譯方法(Android BSP Compile Method)) |
||
(27 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | |||
− | + | == '''產品介紹(Product introduction )''' == | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | == ''' | + | === '''產品特性(Product Features)''' === |
− | + | *NXP ARM® Cortex®-A9 i.MX6 Dual/Quad up to 1 GHz | |
+ | *Onboard 1GB DDR3 memory and 4GB eMMC | ||
+ | *HDMI and VGA 1920x1080 at 60Hz, Dual Channel 18/24 bit LVDS | ||
+ | *3 UART, 1 GbE, 5 USB 2.0, 20 GPIO, 2 I2C, 1 SPI | ||
+ | *M.2 for WIFI/BT support , mini-PCIe for WIFI/3G support | ||
+ | *Low power consumption, fanless design | ||
+ | *Supports Linux and Android | ||
− | == '''接口布局和尺寸(Layout and Sizes)''' == | + | === '''產品官網連結(Product official website link) ''' === |
+ | |||
+ | [https://www.advantech.com/zh-tw/products/b6edc1fb-ade2-4760-986c-451b7b3d6dd5/rsb-4411/mod_d3901250-b0a0-4a5f-9762-b26fa0c36858 '''RSB-4411'''] | ||
+ | |||
+ | == '''硬件接口說明(Hardware interface introduction)''' == | ||
+ | |||
+ | === '''接口布局和尺寸(Layout and Sizes)''' === | ||
=== '''RSB-4411 接口布局圖 Board Dimension Layout ''' === | === '''RSB-4411 接口布局圖 Board Dimension Layout ''' === | ||
Line 22: | Line 27: | ||
'''[[File:4411front layout 2021-10-01 114250.jpg|RTENOTITLE]]''' | '''[[File:4411front layout 2021-10-01 114250.jpg|RTENOTITLE]]''' | ||
+ | |||
+ | | ||
=== '''接口引脚定義 (Pin definitions)''' === | === '''接口引脚定義 (Pin definitions)''' === | ||
− | + | '''Connector List ''' | |
− | + | ||
− | + | [[File:RSB-4411 Connector List.png|RTENOTITLE]] | |
− | + | ||
− | + | [[RTC_Battery_connectors_(CN1)|RTC Battery connectors (CN1)]] | |
− | + | ||
− | + | [[DC_power_Jack_(CN10)|DC power Jack (CN10)]] | |
− | + | ||
− | + | [[VGA_(CRT1)|VGA (CRT1)]] | |
− | + | ||
+ | [[RS-232/422/485_(COM1)|RS-232/422/485 (COM1)]] | ||
+ | |||
+ | [[Ethernet_Connector_(CN8)|Ethernet Connector (CN8)]] | ||
+ | |||
+ | [[HDMI_(CN11)|HDMI (CN11)]] | ||
+ | |||
+ | [[USB_Connector_(CN11)|USB Connector (CN11)]] | ||
+ | |||
+ | [[USB_OTG_Connector_(CN30)|USB OTG Connector (CN30)]] | ||
+ | |||
+ | [[LVDS_Connector_(CN30)|LVDS Connector (CN30)]] | ||
+ | |||
+ | [[LVDS_Backlight_Connector|LVDS Backlight Connector]] | ||
+ | |||
+ | [[SATA_(CN27)|SATA (CN27)]] | ||
+ | |||
+ | [[SATA_Power_(CN25)|SATA Power (CN25)]] | ||
+ | |||
+ | [[Debug_Port_(CN5)|Debug Port (CN5)]] | ||
+ | |||
+ | [[USB_(Internal_Pin_Header)_(CN12)|USB (Internal Pin Header) (CN12)]] | ||
+ | |||
+ | [[USB_(Internal_Pin_Header)_(CN29)|USB (Internal Pin Header) (CN29)]] | ||
+ | |||
+ | [[MIC_in_(CN23)|MIC in (CN23)]] | ||
+ | |||
+ | [[Line_out_(CN14)|Line out (CN14)]] | ||
+ | |||
+ | [[RS-232_(CN21)|RS-232 (CN21)]] | ||
+ | |||
+ | [[GPIO_(CN31)|GPIO (CN31)]] | ||
+ | |||
+ | [[CAN_CN31|CAN_CN31]] | ||
+ | |||
+ | [[I2C_(CN33/CN34)|I2C (CN33/CN34)]] | ||
+ | |||
+ | [[SPI_(CN35)|SPI (CN35)]] | ||
+ | |||
+ | [[MiniPCIe_(CN3)|MiniPCIe (CN3)]] | ||
+ | |||
+ | [[SIM_Socket_(CN4)|SIM Socket (CN4)]] | ||
+ | |||
+ | [[2.2.2.25._SD_Socket_(SD1)|SD Socket (SD1)]] | ||
+ | |||
+ | [[M.2_(CN3)|M.2 (CN3)]] | ||
+ | |||
+ | |||
+ | === '''Jumper Settings ''' === | ||
+ | |||
+ | '''SW2''' | ||
+ | |||
+ | [[File:RSB-4411 SW2.png|RTENOTITLE]] | ||
+ | |||
+ | '''SW3 ''' | ||
+ | |||
+ | [[File:RSB-4411 sw3 1.png|RTENOTITLE]] | ||
=== '''机械尺寸 ('''Mechanical Characteristics) === | === '''机械尺寸 ('''Mechanical Characteristics) === | ||
Line 40: | Line 103: | ||
'''RSB-4411''' | '''RSB-4411''' | ||
− | + | | |
[[File:4411 Boardsize12021-10-01 114555.jpg|RTENOTITLE]] | [[File:4411 Boardsize12021-10-01 114555.jpg|RTENOTITLE]] | ||
− | + | | |
[[File:4411 Boardsize22021-10-01 114937.jpg|RTENOTITLE]] | [[File:4411 Boardsize22021-10-01 114937.jpg|RTENOTITLE]] | ||
Line 53: | Line 116: | ||
== '''快速入门 (Quick Start)''' == | == '''快速入门 (Quick Start)''' == | ||
− | |||
− | |||
=== '''系统下载 (OS Download)''' === | === '''系统下载 (OS Download)''' === | ||
− | * | + | *'''''Linux系统 (Linux OS) ''''' |
− | |||
− | |||
− | |||
− | |||
− | [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/ | + | [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/OS_Support_List_new Yocto 2.1] |
− | [ | + | [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/OS_Support_List_Yocto_2.5 Yocto 2.5] |
---- | ---- | ||
Line 86: | Line 143: | ||
Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot) | Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot) | ||
− | | + | |
Step4: 確認開機選擇指撥開關 | Step4: 確認開機選擇指撥開關 | ||
Line 92: | Line 149: | ||
SD 卡開機模式: | SD 卡開機模式: | ||
− | | + | |
− | |||
+ | | ||
Step3:打開電源 和 終端機 (Turn on the Power & Terminal) | Step3:打開電源 和 終端機 (Turn on the Power & Terminal) | ||
− | | + | |
− | |||
+ | | ||
Step4: 解壓縮flash tools 檔案,並複製到U盤中(Unzip the flash tools file , then copy to USB Disk) | Step4: 解壓縮flash tools 檔案,並複製到U盤中(Unzip the flash tools file , then copy to USB Disk) | ||
Line 135: | Line 192: | ||
Flow Control流控:无</pre> | Flow Control流控:无</pre> | ||
− | : | + | : |
Tera Term Tool | Tera Term Tool | ||
Line 151: | Line 208: | ||
Debug port connection (串口連接) | Debug port connection (串口連接) | ||
− | + | | |
− | |||
+ | | ||
Log into Terminal Tool (进入串口调试终端): | Log into Terminal Tool (进入串口调试终端): | ||
− | + | | |
---- | ---- | ||
+ | |||
+ | | ||
== '''Linux系统的基本使用(Linux System Basic Operating Method)''' == | == '''Linux系统的基本使用(Linux System Basic Operating Method)''' == | ||
− | === ''' | + | === ''' 乙太網路使用方法(Ethernent Testing Method)''' === |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
'''Command : ifconfig ''' | '''Command : ifconfig ''' | ||
Line 228: | Line 263: | ||
[[File:4GTest2021-09-09 133204.jpg|RTENOTITLE]] | [[File:4GTest2021-09-09 133204.jpg|RTENOTITLE]] | ||
− | + | | |
+ | |||
+ | | ||
=== '''GPIO使用方法(GPIO Operating Method)''' === | === '''GPIO使用方法(GPIO Operating Method)''' === | ||
− | [[ | + | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" |
+ | |- | ||
+ | | GPIO Pin | ||
+ | | GPIO Pin define | ||
+ | | GPIO Number[32*(Bank-1)+ IO] | ||
+ | |- | ||
+ | | GPIO_01 | ||
+ | | ENET_RXD/GPIO1_IO27 | ||
+ | | 27 [32*(1-1) + 27] | ||
+ | |- | ||
+ | | GPIO_02 | ||
+ | | ENET_TXD1/GPIO1_IO29 | ||
+ | | 29 [32*(1-1) + 29] | ||
+ | |- | ||
+ | | GPIO_03 | ||
+ | | ENET_CRS_DV/GPIO1_IO25 | ||
+ | | 25 [32*(1-1) + 25] | ||
+ | |- | ||
+ | | GPIO_04 | ||
+ | | ENET_TXD0/GPIO1_IO30 | ||
+ | | 30 [32*(1-1) + 30] | ||
+ | |- | ||
+ | | GPIO_05 | ||
+ | | EIM_BCLK__GPIO6_IO31 | ||
+ | | 191 [32*(6-1) + 31] | ||
+ | |- | ||
+ | | GPIO_06 | ||
+ | | EIM_D30/GPIO3_IO30 | ||
+ | | 94 [32*(3-1) + 30] | ||
+ | |- | ||
+ | | GPIO_07 | ||
+ | | EIM_D31/GPIO3_IO31 | ||
+ | | 95 [32*(3-1) + 31] | ||
+ | |- | ||
+ | | GPIO_08 | ||
+ | | EIM_D21/GPIO3_IO21 | ||
+ | | 85 [32*(3-1) + 21] | ||
+ | |- | ||
+ | | GPIO_09 | ||
+ | | EIM_A25__GPIO5_IO02 | ||
+ | | 130 [32*(5-1) + 2] | ||
+ | |- | ||
+ | | GPIO_10 | ||
+ | | EIM_D20/GPIO3_IO20 | ||
+ | | 84 [32*(3-1) + 20] | ||
+ | |- | ||
+ | | GPIO_11 | ||
+ | | EIM_D23/GPIO3_IO23 | ||
+ | | 87 [32*(3-1) + 23] | ||
+ | |- | ||
+ | | GPIO_12 | ||
+ | | NANDF_CS0/GPIO6_IO11 | ||
+ | | 171 [32*(6-1) + 11] | ||
+ | |- | ||
+ | | GPIO_13 | ||
+ | | NANDF_D2/GPIO2_IO02 | ||
+ | | 34 [32*(2-1) + 2] | ||
+ | |- | ||
+ | | GPIO_14 | ||
+ | | NANDF_WP_B/GPIO6_IO09 | ||
+ | | 169 [32*(6-1) + 9] | ||
+ | |- | ||
+ | | GPIO_15 | ||
+ | | NANDF_D3/GPIO2_IO03 | ||
+ | | 35 [32*(2-1) + 3] | ||
+ | |- | ||
+ | | GPIO_16 | ||
+ | | NANDF_CS3/GPIO6_IO16 | ||
+ | | 176 [32*(6-1) + 16] | ||
+ | |- | ||
+ | | GPIO_17 | ||
+ | | NANDF_CLE/GPIO6_IO07 | ||
+ | | 181 [32*(6-1) + 21] | ||
+ | |- | ||
+ | | GPIO_18 | ||
+ | | NANDF_D4/GPIO2_IO04 | ||
+ | | 36 [32*(2-1) + 4] | ||
+ | |- | ||
+ | | GPIO_19 | ||
+ | | NANDF_D0/GPIO2_IO00 | ||
+ | | 32 [32*(2-1) + 0] | ||
+ | |- | ||
+ | | GPIO_20 | ||
+ | | NANDF_ALE/GPIO6_IO08 | ||
+ | | 168 [32*(6-1) + 8] | ||
+ | |} | ||
+ | {| border="0" cellpadding="0" cellspacing="0" width="522" | ||
+ | |- | ||
+ | | | ||
+ | |} | ||
+ | | ||
<pre>Loop-back Test (Take GPIO4 and GPIO5 as examples) | <pre>Loop-back Test (Take GPIO4 and GPIO5 as examples) | ||
Line 240: | Line 367: | ||
Step 2: Export GPIO interface | Step 2: Export GPIO interface | ||
− | root@imx8qxprom5620a1 : ~# echo | + | root@imx8qxprom5620a1 : ~# echo 30 > /sys/class/gpio/export |
− | root@imx8qxprom5620a1 : ~# echo | + | root@imx8qxprom5620a1 : ~# echo 191 > /sys/class/gpio/export |
Step 3: Set direction | Step 3: Set direction | ||
Line 260: | Line 387: | ||
RS-232 Test | RS-232 Test | ||
− | + | [[File:RSB-4411 RS232 testing.PNG|RTENOTITLE]] | |
+ | |||
+ | SW3 Setting (SW3設置) | ||
+ | |||
+ | [[File:RSB-4411 sw3.png|RTENOTITLE]] | ||
− | + | | |
− | === ''' | + | RS-485 |
+ | |||
+ | Download Test Tool : [https://www.dropbox.com/sh/2qq7mpimxsqrfn7/AACpFQ2LoqQptr3x_usfjfYQa?dl=0&preview=test485.7z Test485] | ||
+ | |||
+ | <span style="font-size:larger;"><span lang="EN-US" style="font-family:">RS 485 test (</span><span style="font-family:">系統預設</span><span lang="EN-US" style="font-family:">minincom)</span></span> | ||
+ | |||
+ | #<span style="font-size:larger;"><span lang="EN-US" style="font-family:">Switch : 2 ->1 , </span><span lang="EN-US" style="font-style: normal;"><font face="新細明體, serif">others </font></span><span lang="EN-US" style="font-family:">off</span></span> | ||
+ | #<span style="font-size:larger;"><span lang="EN-US" style="font-family:">./test485 /dev/ttymxc1 tx</span></span> | ||
+ | |||
+ | [[File:RSB-4411 RS485 testing-1.PNG|RTENOTITLE]] | ||
+ | |||
+ | <span style="font-size:larger;"> 3. <span lang="EN-US" style="font-family:">minicom -D /dev/ttymxc1</span></span> | ||
+ | |||
+ | <span style="font-size:larger;"><span lang="EN-US" style="font-family:"> [[File:RSB-4411 RS485 testing-2.PNG|RTENOTITLE]]</span></span> | ||
+ | |||
+ | 4. Open two terminal tool | ||
+ | |||
+ | [[File:RSB-4411 RS485 testing-3.PNG|RTENOTITLE]] | ||
+ | |||
+ | | ||
+ | |||
+ | | ||
+ | |||
+ | | ||
+ | |||
+ | === '''藍芽使用方法(BlueTooth Operating Method)''' === | ||
<pre>Command : | <pre>Command : | ||
Line 279: | Line 435: | ||
[[File:BTTest2021-09-09 132449.jpg|RTENOTITLE]] | [[File:BTTest2021-09-09 132449.jpg|RTENOTITLE]] | ||
− | === ''' 遠程訪問及文件傳輸(Remote Access and File Transimmion)''' === | + | |
+ | |||
+ | === '''CAN使用方法 (CAN Test)''' === | ||
+ | |||
+ | Connect device with CAN0 (CN8A) | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># ip link set can0 up type can bitrate 125000</div> | ||
+ | [[File:RSB4411 CAN.png|RTENOTITLE]] | ||
+ | |||
+ | | ||
+ | |||
+ | === '''遠程訪問及文件傳輸(Remote Access and File Transimmion)''' === | ||
''' 查看主板IP位址 ( Chech IP Address ):''' | ''' 查看主板IP位址 ( Chech IP Address ):''' | ||
<pre> Command : ifconfig</pre> | <pre> Command : ifconfig</pre> | ||
− | + | | |
==== Windows下SSH访问及文件传输 ==== | ==== Windows下SSH访问及文件传输 ==== | ||
Line 290: | Line 456: | ||
SSH Remote Log into Device | SSH Remote Log into Device | ||
− | *SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件) | + | *SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件) |
− | *需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码 | + | *需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码 |
− | |||
+ | | ||
[[File:SSHsettingdetail.png|RTENOTITLE]] | [[File:SSHsettingdetail.png|RTENOTITLE]] | ||
Line 299: | Line 465: | ||
[[File:SSHSetting2021-09-10 143631.jpg|RTENOTITLE]] | [[File:SSHSetting2021-09-10 143631.jpg|RTENOTITLE]] | ||
− | + | | |
[[File:Sshsetting12021-09-10 143743n.jpg|RTENOTITLE]] | [[File:Sshsetting12021-09-10 143743n.jpg|RTENOTITLE]] | ||
Line 307: | Line 473: | ||
== '''通用方法(General Method)''' == | == '''通用方法(General Method)''' == | ||
− | === | + | === '''查看CPU温度(Check CPU Temperature)''' === |
<pre> root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600 | <pre> root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600 | ||
# 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°</pre> | # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°</pre> | ||
− | === ''' | + | === '''查看CPU频率(Check CPU Frequency)''' === |
<pre> cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq | <pre> cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq | ||
>> 900000 | >> 900000 | ||
Line 318: | Line 484: | ||
>> 1200000</pre> | >> 1200000</pre> | ||
− | === ''' | + | === '''查看内存容量(Check Memory Capacity)''' === |
<pre>root@imx8qxprom5620a1:/# busybox free -m | <pre>root@imx8qxprom5620a1:/# busybox free -m | ||
total used free shared buffers cached | total used free shared buffers cached | ||
Line 326: | Line 492: | ||
</pre> | </pre> | ||
− | === ''' | + | === '''查看存储容量(Check Storage Capacity)''' === |
<pre style="margin-left: 40px;">root@imx8qxprom5620a1:/# busybox df -h | <pre style="margin-left: 40px;">root@imx8qxprom5620a1:/# busybox df -h | ||
Filesystem Size Used Available Use% Mounted on | Filesystem Size Used Available Use% Mounted on | ||
Line 342: | Line 508: | ||
root@imx8qxprom5620a1:/#</pre> | root@imx8qxprom5620a1:/#</pre> | ||
− | === ''' | + | === '''網路Ping測試(Ping Network Testing)''' === |
<pre> ping 8.8.8.8 | <pre> ping 8.8.8.8 | ||
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. | PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. | ||
Line 348: | Line 514: | ||
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre> | 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre> | ||
− | === ''' | + | === '''設置RTC (RTC Setting) ''' === |
<pre> root@imx8qxprom5620a1:/# systemctl stop ntpdate.service | <pre> root@imx8qxprom5620a1:/# systemctl stop ntpdate.service | ||
root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date | root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date | ||
Line 357: | Line 523: | ||
root@imx8qxprom5620a1:/#'''</pre> | root@imx8qxprom5620a1:/#'''</pre> | ||
− | + | | |
+ | |||
− | == '''Linux BSP編譯方法( | + | == '''Linux BSP編譯方法(Linux BSP Compile Method)''' == |
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV9_User_Guide '''Yocto 2.5'''] === | === [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV9_User_Guide '''Yocto 2.5'''] === | ||
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV8_User_Guide '''Yocto 2.1'''] === | === [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV8_User_Guide '''Yocto 2.1'''] === |
Revision as of 05:13, 8 May 2024
Contents
- 1 產品介紹(Product introduction )
- 2 硬件接口說明(Hardware interface introduction)
- 3 快速入门 (Quick Start)
- 4 Linux系统的基本使用(Linux System Basic Operating Method)
- 5 通用方法(General Method)
- 6 Linux BSP編譯方法(Linux BSP Compile Method)
產品介紹(Product introduction )
產品特性(Product Features)
- NXP ARM® Cortex®-A9 i.MX6 Dual/Quad up to 1 GHz
- Onboard 1GB DDR3 memory and 4GB eMMC
- HDMI and VGA 1920x1080 at 60Hz, Dual Channel 18/24 bit LVDS
- 3 UART, 1 GbE, 5 USB 2.0, 20 GPIO, 2 I2C, 1 SPI
- M.2 for WIFI/BT support , mini-PCIe for WIFI/3G support
- Low power consumption, fanless design
- Supports Linux and Android
產品官網連結(Product official website link)
硬件接口說明(Hardware interface introduction)
接口布局和尺寸(Layout and Sizes)
RSB-4411 接口布局圖 Board Dimension Layout
Rear I/O
接口引脚定義 (Pin definitions)
Connector List
USB (Internal Pin Header) (CN12)
USB (Internal Pin Header) (CN29)
Jumper Settings
SW2
SW3
机械尺寸 (Mechanical Characteristics)
RSB-4411
快速入门 (Quick Start)
系统下载 (OS Download)
- Linux系统 (Linux OS)
Linux 燒錄方法 (Linux Flash eMMC Method)
使用Flash tool 燒錄鏡像到eMMC (Flash image into eMMC by Flash Tools)
Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system)
Step1: 創造一張可開機的SD 卡 (Create a bootable SD card)
Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot)
Step4: 確認開機選擇指撥開關
SD 卡開機模式:
Step3:打開電源 和 終端機 (Turn on the Power & Terminal)
Step4: 解壓縮flash tools 檔案,並複製到U盤中(Unzip the flash tools file , then copy to USB Disk)
解壓縮(Unzip the file )
複製檔案到U盤中 (Copy the flash file to USB Disk)
1. 插入U盤到你的Ubuntu 電腦上 (Plug the USB Disk into you Linux PC
2. 檢視U盤在Ubuntu 系統代號 (Check the USB Disk's symbol in Ubuntu System)
3. 掛載U盤在Ubuntu 系統中
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Check the Sriel port in Device Manager (查看PC端的串口号):
if you can not identify the Serial device , please check your serial driver.
Debug port connection (串口連接)
Log into Terminal Tool (进入串口调试终端):
Linux系统的基本使用(Linux System Basic Operating Method)
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
Command: Ping - I eth1 8.8.8.8 or Ping - I eth0 8.8.8.8
WiFi使用方法(WIFI Testing Method)
Command : # killall wpa_supplicant # ifconfig wlan0 up # wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf # wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf # udhcpc -b -i wlan0''' ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
4G使用方法(4G Testing Method)
Command: Test 4G: (EWM-C117FL06E - USB) Step 1: Connect EWM-C117FL06E to Mini PCIE slot on 9680015491 and connect the card to CN6 PCIe_D slot on ROM-DB5901. Step 2: Connect the antenna 1750007990-01 to the SMA (F) connector on 9680015491 and connect the IPEX connector to MT1 on EWM-C117FL06E module. Step 3: Connect the Mini USB cable from 9680015491 to USB 2.0 Type A port on ROM-DB5901. Step 4: Power on and execute the pppd command to connect to the network.
GPIO使用方法(GPIO Operating Method)
GPIO Pin | GPIO Pin define | GPIO Number[32*(Bank-1)+ IO] |
GPIO_01 | ENET_RXD/GPIO1_IO27 | 27 [32*(1-1) + 27] |
GPIO_02 | ENET_TXD1/GPIO1_IO29 | 29 [32*(1-1) + 29] |
GPIO_03 | ENET_CRS_DV/GPIO1_IO25 | 25 [32*(1-1) + 25] |
GPIO_04 | ENET_TXD0/GPIO1_IO30 | 30 [32*(1-1) + 30] |
GPIO_05 | EIM_BCLK__GPIO6_IO31 | 191 [32*(6-1) + 31] |
GPIO_06 | EIM_D30/GPIO3_IO30 | 94 [32*(3-1) + 30] |
GPIO_07 | EIM_D31/GPIO3_IO31 | 95 [32*(3-1) + 31] |
GPIO_08 | EIM_D21/GPIO3_IO21 | 85 [32*(3-1) + 21] |
GPIO_09 | EIM_A25__GPIO5_IO02 | 130 [32*(5-1) + 2] |
GPIO_10 | EIM_D20/GPIO3_IO20 | 84 [32*(3-1) + 20] |
GPIO_11 | EIM_D23/GPIO3_IO23 | 87 [32*(3-1) + 23] |
GPIO_12 | NANDF_CS0/GPIO6_IO11 | 171 [32*(6-1) + 11] |
GPIO_13 | NANDF_D2/GPIO2_IO02 | 34 [32*(2-1) + 2] |
GPIO_14 | NANDF_WP_B/GPIO6_IO09 | 169 [32*(6-1) + 9] |
GPIO_15 | NANDF_D3/GPIO2_IO03 | 35 [32*(2-1) + 3] |
GPIO_16 | NANDF_CS3/GPIO6_IO16 | 176 [32*(6-1) + 16] |
GPIO_17 | NANDF_CLE/GPIO6_IO07 | 181 [32*(6-1) + 21] |
GPIO_18 | NANDF_D4/GPIO2_IO04 | 36 [32*(2-1) + 4] |
GPIO_19 | NANDF_D0/GPIO2_IO00 | 32 [32*(2-1) + 0] |
GPIO_20 | NANDF_ALE/GPIO6_IO08 | 168 [32*(6-1) + 8] |
Loop-back Test (Take GPIO4 and GPIO5 as examples) Step 1: Connect GPIO4 and GPIO5 Step 2: Export GPIO interface root@imx8qxprom5620a1 : ~# echo 30 > /sys/class/gpio/export root@imx8qxprom5620a1 : ~# echo 191 > /sys/class/gpio/export Step 3: Set direction root@imx8qxprom5620a1 : ~# echo out > /sys/class/gpio/gpio1/direction root@imx8qxprom5620a1 : ~# echo in > /sys/class/gpio/gpio2/direction Step 4: Read value and set output value then check root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 0r oot@imx8qxprom5620a1 : ~# echo 1 > /sys/class/gpio/gpio1/value root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 1
串口使用方法(Serial Port Operating Method)
RS-232 Test
SW3 Setting (SW3設置)
RS-485
Download Test Tool : Test485
RS 485 test (系統預設minincom)
- Switch : 2 ->1 , others off
- ./test485 /dev/ttymxc1 tx
3. minicom -D /dev/ttymxc1
4. Open two terminal tool
藍芽使用方法(BlueTooth Operating Method)
Command : $ hciconfig hci0 up $ bluetoothctl $ discoverable on $ pairable on $ scan on [NEW] FC:18:3C:8D:75:F4 myphone $ scan off $ pair FC:18:3C:8D:75:F4 $ connect FC:18:3C:8D:75:F4
CAN使用方法 (CAN Test)
Connect device with CAN0 (CN8A)
遠程訪問及文件傳輸(Remote Access and File Transimmion)
查看主板IP位址 ( Chech IP Address ):
Command : ifconfig
Windows下SSH访问及文件传输
SSH Remote Log into Device
- SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
- 需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600 # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°
查看CPU频率(Check CPU Frequency)
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq >> 900000 cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq >> 1200000
查看内存容量(Check Memory Capacity)
root@imx8qxprom5620a1:/# busybox free -m total used free shared buffers cached Mem: 1794920 516080 1278840 17252 9852 80292 -/+ buffers/cache: 425936 1368984 Swap: 0 0 0
查看存储容量(Check Storage Capacity)
root@imx8qxprom5620a1:/# busybox df -h Filesystem Size Used Available Use% Mounted on /dev/root 13.4G 1.7G 11.1G 13% / devtmpfs 395.8M 4.0K 395.8M 0% /dev tmpfs 876.4M 0 876.4M 0% /dev/shm tmpfs 876.4M 16.5M 859.9M 2% /run tmpfs 876.4M 0 876.4M 0% /sys/fs/cgroup tmpfs 876.4M 4.0K 876.4M 0% /tmp tmpfs 876.4M 280.0K 876.2M 0% /var/volatile /dev/mmcblk0p2 13.6G 1.7G 11.3G 13% /run/media/mmcblk0p2 /dev/mmcblk0p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk0p1 /dev/mmcblk1p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk1p1 tmpfs 175.3M 88.0K 175.2M 0% /run/user/0 root@imx8qxprom5620a1:/#
網路Ping測試(Ping Network Testing)
ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
設置RTC (RTC Setting)
root@imx8qxprom5620a1:/# systemctl stop ntpdate.service root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date Wed Sep 8 16:07:00 UTC 2021 Wed Sep 8 16:07:00 UTC 2021 root@imx8qxprom5620a1:/# date Wed Sep 8 16:07:06 UTC 2021 root@imx8qxprom5620a1:/#'''