Revision as of 03:20, 30 May 2024

產品介紹

產品特性(Features)

• NXP i.MX 93 Cortex-A55 Dual-core (up to 1.7GHz)
• 1 x Arm Cortex-M33 core
• 1 x Ethos®-U65 microNPU
• 1 x 2GB LPDDR4X up to 3733MT/s
• 1 x 4 lane MIPI-DSI
• 2 x USB 2.0, 5 x UART, 4 x I2C, 16 x GPIO, 2 x PWM, 2 x CAN-FD 
• Compact size form factor - OSM Size L (45 x 45 mm)
• Support Ycoto Linux

產品官網連結(Product information Link)

ROM-2820

接口布局和尺寸(Layout and Sizes)

ROM-2820 接口布局圖 Board Dimension Layout 

ROM-ED91 接口布局圖 Board Dimension Layout

主板内置插针式引脚排序方式 (Pin Header defination) 

Internal I/O, Jummper/Switch List:

Rear I/O 

LED Function List 

Switch Settings 

• SW1301(BT0_CFG1/4, BT1_CFG6/7/9/11)
• SW1302(BT0_CFG0, BT1_CFG4/5, BOOT_SEL0#/1#, MOD_ON)
• SW1203 (UARTB_MODE0, UART_MODE1)
• SW1204 (UARTB_TERM,_UARTB_SLEW)
• SW1206_(U1205_RX_TERM,_U1205_MODE2)
• SW1201 (UARTA_MODE0, UART_MODE1)
• SW1202 (UARTA_TERM,_UARTA_SLEW)
• SW1205_(U1202_RX_TERM,_U1202_MODE2)
• SW1303_(Power_button)
• SW1304_(Reset_button)
• SD_SLT_(SD_select)
• LVDS_VDD_SLT_(LVDS_power_select_select_header)
• LVDS_BKLT_SLT_(LVDS_Backlight_power_select_header)

接口引脚定義 (Connector Pin definitions)

• DCIN1401
• COMB
• COMA
• LAN
• USB1
• USB0_OTG1
• AJ(Audio_Jack)
• MIC
• CAN
• COME_DEBUG(M-core_debug)
• COMC
• COMD(A-code_debug)
• I2C1101
• I2C1102
• CN601(M.2_Key_E)
• CN701(MIPI-CSI)
• LVDS
• LVDS_BKLT_PWR
• BAT1
• I2S_CN(I2S)
• CN501(CAN0_H/CAN0_L)
• GPIO1101
• SPI_CN1101(PWM)
• CN1101(SPI)

机械尺寸  (Mechanical Characteristics)

ROM-2820

快速入门 (Quick Start)

系统下载 (OS Download)

• 'Linux系统 (Linux OS)'   

Yocto 4.2: IoTGateway/BSP/Linux/iMX8/OS Support List 4.2 release ROM-2820 - ESS-WIKI (advantech.com.tw) 

Linux 燒錄方法 (Linux Flash eMMC Method)

使用Flash tool 燒錄鏡像到eMMC (Flash image into eMMC by Flash Tools) 

Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system) 

Step1: 創造一張可開機的SD 卡 (Create a bootable SD card)

Command :

~$ sudo dd if=2820A1AIM34LIVC0054_iMX8ULP_1G_flash_tool/image/imx-image-full-imx8ulprom2820a1-20230627062759.rootfs.wic of=/dev/sde bs=1M conv=fsync status=progress

Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot)

Step3: 確認開機選擇指撥開關

Step4:打開電源 和 終端機 (Turn on the Power & Terminal)

Step5: 複製flash tool到U盤中, 解壓縮flash tools檔案,(copy to USB Disk, then unzip the flash tools file)(Test with 32G SD card)

    複製檔案到U盤中 (Copy the flash file to USB Disk), 解壓縮flash tool到home目錄(Unzip the file to home)

1. tar zxvf /run/media/New\ Volume-sda/2820A1AIM34LIVC0054_iMX8ULP_1G_flash_tool.tgz -C ~

5. 進入flsah tool下的mk_inand資歷夾, 執行指令./mksd-linux.sh /dev/mmcblk0燒錄image到eMMC(Connect USB Disk to ROM-2820 system, extract the flash tool and browser to mk_inand folder and execute flash shell script "./mksd-linux.sh /dev/mmcblk0"

解壓縮後如果沒有mksd-linux.sh檔案, 可以到以下連結下載並複製到mk_inand資料夾下(If there is no mksd-linux.sh file in mk_inand directory. Please download from the link below and place it in mk_inand directory:

mksd-linux.sh

6. 切換開機switch來設定成從eMMC開機(Change boot switch to boot from eMMC. Reboot system).

Debug 串口調試 (Debug port Setting)

以 Tera Term  为例介绍如何使用串口调试功能 ?'"`UNIQ--pre-00000001-QINU`"'?

Tera Term Tool 

Check the Sriel port in Device Manager (查看PC端的串口号)：

if you can not identify the Serial device , please check your serial driver. 

Debug port connection (串口連接) 

Log into Terminal  Tool (进入串口调试终端)：

Linux系统的基本使用(Linux System Basic Operating Method)

UUU 使用方法(USB Connection (OTG port))

Connect USB cable to USB OTG port.

Change boot switch to " " to boot from force recovery mode.

Download uuu tool from link below:

Releases · nxp-imx/mfgtools (github.com)

The uuu verison we tested is 1.4.193: uuu

uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.193-0-ge56424c

Perpare uboot and image files below:

1. Download uuu

Type command below to flash eMMC:

Display Setting (ROM-2820)

      U-boot Command :

• Display

Audio(Audio Testing Methid)

0 [sgtl5000 ]: sgtl5000 - sgtl5000 
                sgtl5000

Record and playback:

M.2 WiFi/BT測試方法(M.2 WiFi/BT Testing Method)

• Test Wi-Fi with EWM-xxxx  on C0048 version: Change SD_SLT to 2-3

In Linux user space:

Add name server: nameserver 8.8.8.8 in resolv.conf file

Test BT:

• Test Wi-Fi with EWM-W194M201E Module (SDIO Interface)

Step 1: Press enter after boot. The system will stop at u-boot, and change dtb file by below command.

Step 2: Install driver by below command.

Step 3: WIFI test command.

• Test Bluetooth with EWM-W194M201E Module (UART Interface)

Step 1: Please refer to above step 1.
Step 2: Please refer to above step 2.

Step 3: Bluetooth test command.

Serial Port測試方法(Serial Testing Method)(COM A/C)

• RS-232 Loopback Test (eg. COMA: ttyLP0):

Step 1: First change ROM-ED91 SW1201 to ‘01’.
Step 2: Run test command.

• RS-422 Test:

Step 1: First change ROM-ED91 SW1201 to ‘11’.
Step 2: Test RS-422 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following:

Adam-4520 RX- <-->ROM-2820 COMA DB9 Pin 1,
Adam-4520 RX+ <-->ROM-2820 COMA DB9 Pin 2,
Adam-4520 TX- <-->ROM-2820 COMA DB9 Pin 4,
Adam-4520 TX+ <--> ROM-2820 COMA DB9 Pin 3

Step 3: Run below command:

• RS-485 Test:

Step 1: First change ROM-ED91 SW1201 to ‘10’.
Step 2: Test RS-485 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following:

Adam-4520 Data- <-->ROM-2820 COMA DB9 Pin 1,
Adam-4520 Data+ <-->ROM-2820 COMA DB9 Pin 2

Step 3: Run below command:

I2C測試方法(I2C Testing Method)

Step 1: Plug in ROM-EG70
Step 2: Test by below command (eg. I2C-6 I2C_1101):

USB測試方法(USB Testing Method)

USB disk test (USB 2.0)
Step 1: Issue the following command (lsusb -t) after inserting a USB disk into the USB 2.0 port to check if the USB device is listed. Step 2: Test (eg. if usb disk is /dev/sda)

RTC測試方法(RTC Testing Method)

Step 1: Set system time to current, then write to RTC

Step 2: Set one incorrect time, then read time from RTC to verify

eMMC/SD測使方法(eMMC/SD Testing Method)

Device Routes
eMMC: /dev/mmcblk0 
SD: /dev/mmcblk2

Test (eg. emmc)

Step 1: Test command:

乙太網路使用方法(Ethernent Testing Method)

Command : ifconfig 

Command: Ping - I eth1 8.8.8.8  or Ping - I eth0 8.8.8.8  

GPIO使用方法(GPIO Operating Method)

GPIO pin:

GPIO Loopback Test (Using GPIO1 and GPIO2 as examples)

Step 1: Connect GPIO1 and GPIO2

Step 2: Export GPIO interface

Step 3: Set GPIO direction

Step 4: Read value and set output value than check

Camera使用方法(Camera Testing Method)

MIPI-CSI0 (Tested with OV5640 + mini-SAS to MIPI-CSI Cable): OV5640 CSI (CN701): Connect OV5640 camera to EG-55 CAM3

Step 1: Take pictures

Step 2: View on panel

PWM測試方法(PWM Testing Method)

Please use oscilloscope to check waveform.

PWM1:

PWM2:

PWM3:

PWM4:

PWM5:

CAN Bus

Step 1: Prepare two pcs rom-2820. One for ‘Node A’ one for ‘Node B’
Step 2: Connect these two boards (HI-HI/LO-LO)
Step 3: The test steps and screen are as below :

LPUART

Step 1: Change ROM-ED91 SW1203 to '01'.
Step 2: Connect COM-B and COM-E to PC.
Step 3: Set RTS/CTS flow control for COM-B in Putty.exe

Step 4: After select the test mode ‘U’ to verify LPUART2, you will see below screen.

Step 5: If tester can input any characters/strings and show that at COM-B means test successful.

遠程訪問及文件傳輸(Remote Access and File Transimmion)

              查看主板IP位址 ( Chech IP Address )：​ ?'"`UNIQ--pre-00000002-QINU`"'?

SSH访问及文件传输

SSH Remote Log into Device 

• SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
• 需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码

通用方法(General Method)

查看CPU温度(Check CPU Temperature)

?'"`UNIQ--pre-00000003-QINU`"'?

查看内存容量(Check Memory Capacity)

?'"`UNIQ--pre-00000004-QINU`"'?

查看存储容量(Check Storage Capacity)

?'"`UNIQ--pre-00000005-QINU`"'?

設置RTC (RTC Setting) 

?'"`UNIQ--pre-00000006-QINU`"'?

查看系統時間 (Check the system) 

root@imx8ulprom2820a1:/# timedatectl
[   41.402592] kauditd_printk_skb: 6 callbacks suppressed
[   41.402611] audit: type=1334 audit(45.332:16): prog-id=15 op=LOAD
[   41.417884] audit: type=1334 audit(45.344:17): prog-id=16 op=LOAD
               Local time: Thu 1970-01-01 00:00:46 UTC
           Universal time: Thu 1970-01-01 00:00:46 UTC      
                 RTC time: Thu 1970-01-01 00:00:45            <-----  Real-Time Clock，RTC 
                Time zone: Universal (UTC, +0000)              <------ Time zone 目前
System clock synchronized: no
              NTP service: active
              RTC in local TZ: no         

Note : 

Change Time Zone   ?'"`UNIQ--pre-00000007-QINU`"'?

           Local time: Fri 2024-05-03 09:07:42 CST
           Universal time: Fri 2024-05-03 01:07:42 UTC
                RTC time: Fri 2024-05-03 09:07:42
                Time zone: Asia/Taipei (CST, +0800)
System clock synchronized: yes
              NTP service: active
              RTC in local TZ: yes

Time Zone List 

$ sudo timedatectl list-timezones

Africa/Abidjan

Africa/Accra

Africa/Addis_Ababa

Africa/Algiers

Africa/Asmara

Africa/Bamako

Africa/Bangui

Africa/Banjul

Africa/Bissau

Africa/Blantyre

Africa/Brazzaville

Africa/Bujumbura

Africa/Cairo

Africa/Casablanca

Linux BSP編譯方法(Linux BSP Compile Method)

Yocto 4.2