Revision as of 02:38, 13 June 2024

Getting Started

Conventions

${PREBUILT_IMAGE} : compressed prebuilt image (*.img.gz)

${CONTAINER_NAME} : container name (e.g. imx8LBVA0016)

${BSP_TARBALL} : BSP tarball (*.tgz)

${BSP_HOME} : home directory of the BSP

${BDIR} : build directory (e.g. build_x11)

${MX8PROC} : i.MX8 Processor

mx8mq for iMX8M Dual Core

mx8mm for iMX8MM

mx8mp for iMX8MP

mx8qm for iMX8QM

mx8qxp for iMX8QXP

 

${IMX8PROC} : i.MX8 Processor

imx8mq / imx8mm / imx8qm /imx8qxp /imx8mp

${BOARD} : available target boards list below

rom5720

rom5721

rom7720

rom5620

rom3620

rom5722

rsb3720

epcr5710

rsb3730

${BOARD_REV} : board revision

a1

${MC} : machine code combined with ${IMX8PROC}${BOARD}${BOARD_REV}

for example,

imx8mqrom5720a1 for ROM-5720 A1

imx8qmrom7720a1 for ROM-7720 A1

imx8qxprom5620a1 for ROM-5620 A1

imx8qxprom3620a1 for ROM-3620 A1

imx8mmrom5721a1 for ROM-5721 A1

imx8mprom5722a1 for ROM-5722 A1

imx8mprsb3720a1 for RSB-3720 A1

imx8mpepcr5710a1 for EPC-R5710 A1

imx8mmrsb3730a2 for RSB-3730 A2

 

You can also use the command below to check supported machines on BSP

$ source setup-environment

 

${MEM_SIZE} : memory size

 2G/4G

${UC} : u-boot config

 1G/2G/4G/FSPI_1G/FSPI_2G...

${SD_DEVICE} : device name of SD card in Linux (e.g. /dev/sdf)

${SDCARD_IMAGE} : sdcard image built by bitbake (VA0033 ~ VA0362: *.wic.bz2; VA0386 ~ latest version: *.sdcard)

${WORKSPACE} : host workspace folders

${UBOOT} :u-boot version(e.g. 2016.03)

${KERNEL} : linux kernel version(e.g. 4.14.98)

${TOOLCHAIN} : toolchain installed directory(e.g. /opt/fsl-imx-x11/4.1.15-2.0.0)

debug console / serial console

serial terminal program (e.g. minicom, putty, teraterm ...) that serial port is configured to 115200 8N1

terminal console

terminal program (e.g. gnome-terminal, xfce4-terminal ...)

Docker install and setting

If you don't have docker in your system, then you can follow the below  steps to install docker and run it first.

To install Docker Engine on your platform

Please refer to <a alt="<a alt="https://docs.docker.com/engine/installation/" href="https://docs.docker.com/engine/installation/" title="https://docs.docker.com/engine/installation/">https://docs.docker.com/engine/installation/</a>" href="<a alt="https://docs.docker.com/engine/installation/" href="https://docs.docker.com/engine/installation/" title="https://docs.docker.com/engine/installation/">https://docs.docker.com/engine/installation/</a>" title="<a alt="https://docs.docker.com/engine/installation/" href="https://docs.docker.com/engine/installation/" title="https://docs.docker.com/engine/installation/">https://docs.docker.com/engine/installation/</a>">Docker Installation Guide</a> for details

To pull <a alt="<a alt="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" href="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" title="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/">https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/</a>" href="<a alt="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" href="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" title="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/">https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/</a>" title="<a alt="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" href="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/" title="https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/">https://hub.docker.com/r/advrisc/u12.04-imx6lbv3/</a>">ubuntu 18.04 image from Docker Hub</a> 

$ docker pull advrisc/u18.04-imx8lbv1

To create container

$ docker run --privileged -it --name ${CONTAINER_NAME} -v ${WORKSPACE}:/home/adv/adv-release-bsp -v /dev:/dev -v /lib/modules:/lib/modules -v /usr/src:/usr/src advrisc/u18.04-imx8lbv1 /bin/bash

Get BSP

You have two methods to put BSP into container created above

Download_BSP_From_GitHub

The following example shows how to download the Advantech Yocto BSP from GitHub.

For this example, a directory called adv-release-bsp is created for the project.

Refer to <a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FOS%20Support%20List">IoTGateway/BSP/Linux/iMX8/OS_Support_List</a> , Official version "imx8LBVA0209" is taken as an example :

$ git config --global user.name "Your Name"
$ git config --global user.email you@example.com
$ sudo chown adv:adv adv-release-bsp
$ cd adv-release-bsp
$ repo init -u git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git -b imx-linux-zeus -m imx8LBVA0428.xml 
$ repo sync

If you want to get latest bsp

$ repo init -u <a alt="git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git" href="git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git" title="git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git">git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git</a>  <span>-b imx-linux-zeus -m </span>imx-5.4.70-2.3.0.xml 
$ repo sync

If you suffer "server certificate verification failed", you can use the following command to disable SSL verification in git repositories with self-signed certificates.

$ export GIT_SSL_NO_VERIFY=1

or

$ git config --global http.sslverify false

If you get "The unauthenticated git protocol on port 9418 is no longer supported.", you can try it.

$ git config --global url."https://".insteadOf git://

Important : As of March 31, 2023, all source repositories have been migrated to other platforms and the project has been shut down. ** Repo sync will be fail.

Solution  :

(1) If you repo current xml file, repo sync is success. Example:

 $ repo init -u [git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git] <span>-b imx-linux-zeus -m </span>imx-5.4.70-2.3.0.xml 

(2) If you repo tag version xml file, please follow " <a href="Yocto3.0%20Repo%20Fail%20SOP">Yocto3.0_Repo_Fail_SOP</a> " to modify XML File.  Example:

 $ repo init -u git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git -b imx-linux-zeus -m imx8LBVA0428.xml <- Tag XML

Copy BSP tarball to Container

If you have BSP tarball (eg. imx8LBVA0029_2019-10-23.tgz), then you have to copy it into container.

Follow the steps below:

1.Exit container and back to local machine

$ exit

2.Copy BSP tarball to ${WORKSPACE} , and change owner

$ cp imx8LBVA0029_2020-10-23.tgz <b>${WORKSPACE}</b>
$ sudo chown adv:adv ${WORKSPACE}/imx8LBVA0029_2020-10-23.tgz&nbsp;

3.Back to container

$ docker start <b>${CONTAINER_NAME}</b>
$ docker attach <b>${CONTAINER_NAME}</b>

4.Unpack BSP tarball

$ tar zxvf imx8LBVA0029_2020-10-23.tgz

Downloads tarball

Not necessarily step

During building  Yocto image , it will generate downloads folder which includes all packages we need , but it usually can't fetch normally, so we keep this downloads folder. Then we can reduce some fetch failed issue.

You can get Downloads tarball (downloads_imx8_5.4.24.tar.gz) or (downloads_imx8_5.4.70.tar.gz) from following URL:

<a alt="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz</a>" href="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz</a>" title="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.24.tar.gz</a>">[downloads_imx8_5.4.24.tar.gz</a>], md5 checksum: 648a6aa9d03be61ee21611b729250319

<a alt="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz</a>" href="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz</a>" title="<a alt="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" href="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz" title="https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz">https://www.dropbox.com/sh/3z9hh9zht98mzil/AACYhzJkMQq_om6cru9mM-wha/officialbuild/imx8_yocto_bsp_3.0?dl=0&preview=downloads_imx8_5.4.70.tar.gz</a>">[downloads_imx8_5.4.70.tar.gz</a>], md5 checksum: ec2a0da745e57329a73965f9bd7ff0c9

If you get downloads tarball, you can copy to your ${WORKSPACE}

Follow the steps below:

1.Exit container and back to local machine

$ exit

2.Copy Downloads tarball to ${WORKSPACE} , and change owner

$ cp downloads_imx8_5.4.24.tar.gz <b>${WORKSPACE}</b>
$ sudo chown adv:adv ${WORKSPACE}/downloads_imx8_5.4.24.tar.gz&nbsp;

3.Back to container

$ docker start <b>${CONTAINER_NAME}</b>
$ docker attach <b>${CONTAINER_NAME}</b>

4.Unpack Downloads tarball

$ tar zxvf downloads_imx8_5.4.24.tar.gz

5.make link to downloads folder

$ cd adv-release-bsp
$ ln -s ${WORKSPACE}/downloads_imx8_5.4.24 downloads

Introducing BSP

The BSP is based on Yocto Project with Freescale enhanced features for i.MX8, plus specific target board features from Advantech Inc..

The Advantech Yocto Project BSP Release directory contains a "sources" directory, which contains the recipes used to build,

one or more build directories, and a set of scripts used to set up the environment.

The recipes used to build the project come from both the community and Advantech. The Yocto Project layers are downloaded

to the sources directory. This sets up the recipes that are used to build the project.

Naming Rule

The tarball/prebuilt image name is consist of the model name followed by "LB" or "LI" plus version number and released date.

For example, BSP file name: imx8LBVA0010_2019-08-27.tgz

which , "LB" is acronym of Linux BSP,

           "VA0010" stands for Version A.0010

<nowiki>.</nowiki>

 

For example, Yocto image name: '5720A1AIM20LIVA0010_iMX8M_2G_2020-08-27.img.gz'

which "5720A1" stands for ROM-5720 A1

          "LI" is acronym for prebuilt Linux Image

          "2G" is DDR size

BSP Content

Build Instructions

To create one new build environment

Perform the following commands in terminal console

$ cd ${BSP_HOME}

$ MACHINE=${MC} DISTRO=fsl-imx-xwayland source imx-setup-release.sh -b ${BDIR}

 

We can specify u-boot default config like below

$ MACHINE=${MC} UBOOT_CONFIG=${UC} DISTRO=fsl-imx-xwayland source imx-setup-release.sh -b ${BDIR}

Example :  MACHINE=imx8mmrsb3730a1  UBOOT_CONFIG=2G  DISTRO=fsl-imx-xwayland source imx-setup-release.sh -b 3730

 

You need to read and accept the EULA.

<img _fck_mw_filename="Accept EULA.png" _fck_mw_origimgheight="29" _fck_mw_origimgwidth="444" alt="RTENOTITLE" src="/wiki/images/1/1d/Accept_EULA.png" style="vertical-align:middle;" title="RTENOTITLE" />

To continue an exist build environment

Perform the following commands in terminal console

$ cd ${BSP_HOME}

$ source setup-environment ${BDIR}

 

To build sdcard image

To create/continue a build environment

Perform the following command in terminal console

$ bitbake imx-image-full

 

The file, imx-image-full-${MC}.wic.bz2 or VA0386 ~ latest version: imx-image-full-${MC}.rootfs.sdcard, will be located in directory, ./tmp/deploy/images/${MC}, while building process finished successfully.

To build toolchain installer

To create/continue a build environment

Perform the following command in terminal console

$ bitbake meta-toolchain

 

The below installer will be located in the directory "./tmp/deploy/sdk".

fsl-imx-xwayland-glibc-x86_64-meta-toolchain-aarch64-toolchain-${KERNEL}-zeus.sh

 

To build bootloader

To create/continue a build environment

Perform the following command in terminal console

$ bitbake imx-boot

 

To build linux kernel

To create/continue a build environment

If you operate on docker images, please install tmux application before running this command

$ sudo apt-get install tmux

 

 

Type following command to enter tmux

$ tmux

 

 

Perform the following command in terminal console to show up menuconfig

$ bitbake linux-imx -c menuconfig

 

 

After edit menuconfig, type following command to exit tmux windows

$ exit

 

 

to build kernel image

$ bitbake linux-imx

 

 

The two files, Image & Image-${IMX8PROC}-${BOARD}-${BOARD_REV}.dtb, will be located in the directory, ./tmp/deploy/images/${MC}.

Creating boot-up on-board flash from prebuilt image

To create one boot-up SD card

Perform the following command in terminal console

# gunzip -c ${PREBUILT_IMAGE} | dd of=${SD_DEVICE} bs=1M

# sync

 

Creating boot-up on-board flash from built sdcard image

To create one boot-up SD card

Perform the following commands in terminal console

$ pushd ${BSP_HOME}/${BDIR}/tmp/deploy/images/${MC}

$ sudo bzcat ${SDCARD_IMAGE} | sudo dd of=${SD_DEVICE} bs=1M  (VA0033 ~ VA0362)

$ sudo cat ${SDCARD_IMAGE} | sudo dd of=${SD_DEVICE} bs=1M  (VA0386 ~ latest version)

$ sync

$ popd

Note : ues the .sccard file.

 

Debug console information

If you want to see debug message from device, you need to prepare for hardware device and software tool.

Preparing for hardware device

• The following URL provides information about the debug port slot and the debug port line for each device

<a href="Debug%20Port%20Information%23i.MX6">Debug Port Information</a>

Preparing for software tool

• You need to prepare the debug console tool. For example: "minicom" tool or "putty" tool.
• Baud rate: 115200

One step build image

Our machine must be pre-installed docker

Download the following script can quickly build our image.

$ wget <a alt="https://raw.githubusercontent.com/ADVANTECH-Corp/RISC_tools_scripts/zeus/imx8/adv_imx8_build.sh" href="https://raw.githubusercontent.com/ADVANTECH-Corp/RISC_tools_scripts/zeus/imx8/adv_imx8_build.sh" title="https://raw.githubusercontent.com/ADVANTECH-Corp/RISC_tools_scripts/zeus/imx8/adv_imx8_build.sh">https://raw.githubusercontent.com/ADVANTECH-Corp/RISC_tools_scripts/zeus/imx8/adv_imx8_build.sh</a>
$ sudo chmod a+x adv_imx8_build.sh

Build image

$ sudo ./adv_imx8_build.sh ${BOARD}
$ sudo ./adv_imx8_build.sh rom5720

Our image will be in workspace folder.

workspace/${BDIR}/tmp/deploy/images/${MC}

Then refer to <a alt="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image</a>" href="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image</a>" title="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide#Creating_boot-up_on-board_flash_from_built_sdcard_image</a>">Creating_boot-up_on-board_flash_from_built_sdcard_image</a> to build SD card.

Customization

Package addition

To add tcf-agent & openssh-sftp-server

Navigate to the directory where fsl-image-adv.inc located

$ cd ${BSP_HOME}/sources/meta-advantech/meta-fsl-imx/recipes-fsl/images

 

Add following line to fsl-image-adv.inc

IMAGE_INSTALL += " tcf-agent openssh-sftp-server "

 

<a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20continue%20an%20exist%20build%20environment">Continue an exist build environment</a> and <a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20build%20sdcard%20image">build sdcard image</a>

To add chromium browser

Navigate to the directory where local.conf located

$ cd ${BSP_HOME}/${BDIR}/conf

 

• Method 1(Suggest): Add following one line to local.conf

CORE_IMAGE_EXTRA_INSTALL += "chromium-ozone-wayland"

• Method 2: Add following two lines to local.conf

IMAGE_INSTALL_append = \
   "${@bb.utils.contains('DISTRO_FEATURES', 'wayland', ' chromium-ozone-wayland libexif', \
       bb.utils.contains('DISTRO_FEATURES',     'x11', ' chromium-x11 libexif', \
                                                        <i>, d), d)}&quot;</i>
LICENSE_FLAGS_WHITELIST = \
   &quot;${@bb.utils.contains(&#39;DISTRO_FEATURES&#39;, &#39;wayland&#39;, &#39;commercial&#39;, \
       bb.utils.contains(&#39;DISTRO_FEATURES&#39;,     &#39;x11&#39;, &#39;commercial&#39;, \
                                                       <i>, d),&quot;</i>

<a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20continue%20an%20exist%20build%20environment">Continue an exist build environment</a> and <a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20build%20sdcard%20image">build sdcard image</a>

To add QtWebEngine

Put the following in ${BSP_HOME}/${BDIR}/conf/local.conf

IMAGE_INSTALL_append += "packagegroup-qt5-webengine"

 

<a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20continue%20an%20exist%20build%20environment">Continue an exist build environment</a> and <a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20build%20sdcard%20image">build sdcard image</a>

Setting up SDK

Please follow the section,<a href="IoTGateway%2FBSP%2FLinux%2FiMX8%2FYocto%20LBV9%20User%20Guide%23To%20build%20toolchain%20installer">To build toolchain installer</a>, to build one toolchain installer

Perform the following command in terminal console

$ cd ${BSP_HOME}/${BDIR}/tmp/deploy/sdk

$ sudo ./fsl-imx-xwayland-glibc-x86_64-meta-toolchain-aarch64-toolchain-5.4-zeus.sh

 

Enter new installed directory or just press Enter to use default directory.

While Proceed[y/n]? shows up, please enter the correct one.

Waiting for the SDK installed (while the following messages show up completely)

<img _fck_mw_filename="Setting up sdk 3.png" _fck_mw_origimgheight="65" _fck_mw_origimgwidth="572" alt="RTENOTITLE" src="/wiki/images/1/17/Setting_up_sdk_3.png" style="vertical-align:middle;" title="RTENOTITLE" />

 

Setting up cross compiling environment

SDK has been set up (ref.<a href="#Setting_up_SDK">Setting up SDK</a>)

Perform the following command in terminal console

$ source ${TOOLCHAIN}/environment-setup-aarch64-poky-linux

 

Build U-Boot in standalone environment

Config u-boot

make ${IMX8PROC}_${BOARD}${BOARD_REV}_${MEM_SIZE}_defconfig

eg.

make imx8mm_rom5721a1_2G_defconfig

Build u-boot

make -j4

Build imx-boot image by using imx-mkimage

Get imx-boot tarball from our server Here we take rom5721 as an example:

tar zxvf 5721A1AIM20LIVA0118_iMX8MM_imx-boot.tgz 
cd 5721A1AIM20LIVA0118_iMX8MM_imx-boot/ 

In this folder , we have two script as below: Copy necessary files to imx-mkimage folder

./cp_uboot.sh ${uboot path} ${IMX8PROC}

Make imx-boot image

./mk_imx-boot.sh ${IMX8PROC}

eg.

./cp_uboot.sh ../uboot-imx6 <b>imx8m</b>
./mk_imx-boot.sh <b>imx8mm</b>

Replace imx-boot

Perform the following command to transfer to on-board flash

$ dd if=flash.bin of=/dev/mmcblk0 bs=1K seek=<offset> conv=fsync

Where offset is:

33 - for i.MAX 8QuadMax A0, i.Mx 8QuadXPlus A0, i.MX 8M Quad, and i.MX 8M Mini

32 - for iMX 8M PLUS, i.MAX 8QuadXPlus B0/C0 and i.Mx 8QuadMax B0

 

 

Building & updating kernel/modules/dtb manually

The cross compiling environment has been set up. (ref. <a href="#Setting_up_cross_compiling_environment">Setting up cross compiling environment</a>)

Copy BSP tarball to Container

Refer to <a alt="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container</a>" href="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container</a>" title="<a alt="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" href="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container" title="http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container">http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBV9_User_Guide#Copy_BSP_tarball_to_Container</a>">Copy_BSP_tarball_to_Container</a> , copy kernel tarball to ${WORKSPACE} and back to container

change owner & unpack tarball

$ sudo chown adv:adv imx8LBVA0029_2019-10-23_linux-imx.tgz
$ tar zxvf imx8LBVA0029_2019-10-23_linux-imx.tgz

Config kernel

Configure linux kernel

$ cd linux-imx
$ make distclean
$ make imx_v8_adv_defconfig
$ make menuconfig

Start building linux kernel

$ make -j4 Image

When you get error like below

<img _fck_mw_filename="Imx8 error.jpg" _fck_mw_origimgheight="226" _fck_mw_origimgwidth="819" alt="RTENOTITLE" src="/wiki/images/8/85/Imx8_error.jpg" style="vertical-align:middle;" title="RTENOTITLE" />

run command then rebuild

$ unset LDFLAGS 

The kernel image file, Image, is located in the directory "./arch/arm64/boot/".

Start building kernel modules

$ make -j4 modules

Copy all modules to a temporary rootfs directory, "~/temp/rootfs"

$ make modules_install INSTALL_MOD_PATH=~/temp/rootfs

Building device tree blob

$ make -j4 freescale/<span style="color:#7030a0"><b>${IMX8PROC}</b></span>-<span style="color:#7030a0"><b>${BOARD}</b></span>-<span style="color:#7030a0"><b>${BOARD_REV}</b></span>.dtb
eg.
$ make -j4 freescale/imx8mq-rom5720-a1.dtb

The device tree blob, ${IMX8PROC}-${BOARD}-${BOARD_REV}.dtb, is located in the directory "./arch/arm64/boot/dts/freescale/".

Replace kernel & dts

Replace kernel

copy Image to SDcard or emmc

 

Replace dtb file

copy dtb file to SDcard or emmc

 

Improve boot speed

• Bootloader

1.bootdelay time

We can cancel the bootdelay time by setting bootloader environment value.

setenv bootdelay 0
env save
reset

2.Disable console

Disable debug message output can also improve boot speed

Disable kernel message

setenv mmcargs setenv bootargs ${jh_clk} console=${console} modprobe.blacklist=${modprobe.blacklist} root=${mmcroot} video=HDMI-A-1:${videores} <b>quiet</b>
env save
reset

Or

Disable debug port

(1) Yocto machine setting:

modify /sources/meta-advantech/meta-fsl-imx/conf/machine$/${MC}.conf

SERIAL_CONSOLES = ";"

(2) Uboot parameter setting:

• For the imx8mq, imx8mm, imx8mp:

setenv console disabled
env save
reset

• For the imx8qm, imx8qxp:

setenv console disabled
setenv earlycon disabled
setenv mmcargs setenv bootargs console=${console},${baudrate} earlycon=${earlycon},${baudrate} root=${mmcroot}
env save
reset

• Rootfs

TBD

• Services

1. Using systemctl disable remove ,we can remove unnecessary services.

systemctl disable <services>

eg.

systemctl disable boottimes

System Recovery

This section provides detail procedures of restoring the eMMC image.

If you destroy the onboard flash image by accident, you can recover a system following these steps.

• Recovery by SD card

1.Copy 5720A1AIM20LIVA0022_iMX8M_flash_tool.tgz package to your desktop.

2.Insert SD card to PC

3.Make a bootable sd card

# tar zxvf 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool.tgz
# cd 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/sdg

4.Insert SD card and copy 5720A1AIM20LIVA0022_iMX8M_flash_tool to USB disk

5.Insert USB disk and SD card then Boot from SD

6.Enter usb disk folder, make a bootable emmc

# cd /run/media/sda1/
# cd 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/mmcblk0

• Recovery by UUU tool

1.Download uuu tool from (<a alt="<a alt="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" href="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" title="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429">https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429</a>" href="<a alt="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" href="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" title="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429">https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429</a>" title="<a alt="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" href="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" title="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429">https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429</a>"><a alt="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" href="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429" title="https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429">https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20210429</a></a>)

2.burn command

• For Linux

 sudo ./uuu

• For Windows

 uuu.exe 

2.Create a folder with files as below:

1.uuu
2.imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
3.fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard
4.Image_dtb.uuu
5.rootfs.uuu

3.Connect otg cable from PC to device

4.Set the correct boot mode(ROM-5722/ROM5720/ROM5721/ROM5620: 1,2,3-off 4-on, ROM7720: 1,2,3,4,5,6-off or 1,2,4,5,6-off 3-on), then power on

5.Perform the following command:

PS.If you want to burn uboot to mmcblk0 instead of mmcblk0boot0, u-boot must be updated to version 20191101,

1.Burn uboot to emmc
   a)replace uboot in mmcblk0boot0
       sudo ./uuu -b <b>emmc</b> imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
   b)replace uboot in mmcblk0
       sudo ./uuu -b <b>emmc_adv</b> imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
2.Burn rootfs image to emmc
   a)replace uboot in mmcblk0boot0
       sudo ./uuu -b <b>emmc_all</b> imx-boot-imx8mqrom5720a1-sd.bin-flash_evk fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard
   b)replace uboot in mmcblk0
       sudo ./uuu -b <b>emmc_all_adv</b> imx-boot-imx8mqrom5720a1-sd.bin-flash_evk fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard

6.uuu tool will start recovery image to emmc.

7.If we want to burn separately into emmc

   a)replace Image and dtb
       Step 1: rename Image and dtb 
                 _Image
                 _board.dtb
       Step 2: 
                 sudo ./uuu Image_dtb.uuu
   b)replace rootfs
       Step 1: rename rootfs tarball
                 _rootfs.tar.bz2
       Step 2: 
                 sudo ./uuu rootfs.uuu

8.For more usage (<a alt="<a alt="https://github.com/NXPmicro/mfgtools/wiki" href="https://github.com/NXPmicro/mfgtools/wiki" title="https://github.com/NXPmicro/mfgtools/wiki">https://github.com/NXPmicro/mfgtools/wiki</a>" href="<a alt="https://github.com/NXPmicro/mfgtools/wiki" href="https://github.com/NXPmicro/mfgtools/wiki" title="https://github.com/NXPmicro/mfgtools/wiki">https://github.com/NXPmicro/mfgtools/wiki</a>" title="<a alt="https://github.com/NXPmicro/mfgtools/wiki" href="https://github.com/NXPmicro/mfgtools/wiki" title="https://github.com/NXPmicro/mfgtools/wiki">https://github.com/NXPmicro/mfgtools/wiki</a>"><a alt="https://github.com/NXPmicro/mfgtools/wiki" href="https://github.com/NXPmicro/mfgtools/wiki" title="https://github.com/NXPmicro/mfgtools/wiki">https://github.com/NXPmicro/mfgtools/wiki</a></a>)

Package List

In BSP, list all packages which will be built in the image

bitbake -g imx-image-full && cat task-depends.dot | grep -v -e '-native' | grep -v digraph | grep -v -e '-image' | awk '{print $1}' | sort | uniq

<a href=":File%3A20191025.txt">20191025 Package List</a>

Show all recipes (include non-installed packages)

bitbake -s

<a href=":File%3Apackage%20version%2020191025.txt">20191025 Package Version List</a>

You can also check ${BDIR}/tmp/deploy/images/${MC}/fsl-image-qt5-validation-imx-${MC}.manifest

It will show the same content with checking by rpm tool on target board.

On target board, list all packages by rpm tool

rpm -qa --root / --dbpath /var/lib/rpm | sort

<a href=":File%3Arpm%20board%2020191025.txt">20191025 RPM on Board List</a>

Device Tree Source file select

We can setup different dts file on bootloader to enable different devices.

eg.

setenv fdt_file <b>adv-imx8mm-rom5721-a1-dsi2dp</b>.dtb
env save
boot 

ROM-5721

• Display
  • DSI to LVDS
    • g070vw01
      • imx8mm-rom5721-a1.dtb
    • g150xgel05
      • imx8mm-rom5721-a1-dsi2lvds-g150xgel05.dtb
    • g215hvn01
      • imx8mm-rom5721-a1-dsi2lvds-g215hvn01.dtb
  • DSI to DP
    • imx8mm-rom5721-a1-dsi2dp.dtb
  • DSI to HDMI
    • imx8mm-rom5721-a1-adv7535.dtb
  • DSI
    • auog101uan02
      • imx8mm-rom5721-a1-auog101uan02.dtb
• M.2 SDIO
  • Adjust CN43~CN48
  • imx8mm-rom5721-a1-m2-sdio.dtb

ROM-5720

• Display
  • DSI to HDMI
    • imx8mq-rom5720-a1-dcss-adv7535.dtb
    • imx8mq-rom5720-a1-lcdif-adv7535.dtb
    • For weston ui
      • modify /etc/xdg/weston/weston.ini
        • drm-device=card2
  • DSI
    • auog101uan02
      • imx8mq-rom5720-a1-dcss-auog101uan02.dtb
    • For weston ui
      • modify /etc/xdg/weston/weston.ini
        • drm-device=card2
  • Dual Display
    • DSI to HDMI + HDMI
      • imx8mq-rom5720-a1-dual-display.dtb
      • For weston ui
        • modify /etc/xdg/weston/weston.ini
          • drm-device=card1
• M.2 SDIO
  • Adjust CN43~CN48
  • imx8mq-rom5720-a1-m2-sdio.dtb

ROM-5620

• Display
  • LVDS
    • g070vw01
      • imx8mxp-rom5620-a1.dtb
    • g150xgel05
      • imx8qxp-rom5620-a1-lvds-chimei.dtb
    • g215hvn01
      • imx8qxp-rom5620-a1-lvds-dual.dtb
  • LVDS to HDMI
    • imx8qxp-rom5620-a1-hdmi-bridge.dtb
  • DSI to HDMI
    • imx8qxp-rom5620-a1-hdmi-bridge.dtb
  • DSI
    • auog101uan02
      • imx8qxp-rom5620-a1-auog101uan02.dtb
• M.2 SDIO
  • Adjust CN43~CN48
  • imx8qxp-rom5620-a1-m2-sdio.dtb

ROM-7720

• Display
  • HDMI
    • imx8qm-rom7720-a1.dtb
  • LVDS
    • g070vw01
      • imx8qm-rom7720-a1-lvds0.dtb
      • imx8qm-rom7720-a1-lvds1.dtb
    • g215hvn01
      • imx8qm-rom7720-a1-lvds-dual.dtb
  • HDMI + LVDS
    • HDMI + g070vw01
      • imx8qm-rom7720-a1-hdmi-lvds0.dtb
      • imx8qm-rom7720-a1-hdmi-lvds1.dtb
    • HDMI + g215hvn01
      • imx8qm-rom7720-a1-hdmi-lvds-dual.dtb
  • LVDS to HDMI
    • imx8qm-rom7720-a1-it6263.dtb 
• Audio Codec
  • imx8qm-rom7720-a1-sgtl5000.dtb

RSB-3720

• Display
  • HDMI (default)
    • imx8mp-rsb3720-a1.dtb
  • LVDS
    • g070vw01(LVDS0) + HDMI
      • imx8mp-rsb3720-a1-lvds0-auo.dtb
    • g070vw01(LVDS1) + HDMI
      • imx8mp-rsb3720-a1-lvds1-auo.dtb
    • g215hvn01(DUAL LVDS) + HDMI
      • imx8mp-rsb3720-a1-lvds-dual.dtb
  • DSI
    • adv7535(DSI to HDMI) + HDMI
      • imx8mp-rsb3720-a1-adv7535.dtb
    • auog101uan02(DSI) + HDMI
      • imx8mp-rsb3720-a1-auog101uan02.dtb
• Camera
  • OV5640 (default)
    • imx8mp-rsb3720-a1.dtb
  • Basler camrea
    • imx8mp-rsb3720-a1-basler.dtb

ROM-5722

• Display
  • HDMI (default)
    • imx8mp-rom5722-a1.dtb
  • LVDS
    • g070vw01(LVDS0) + HDMI
      • imx8mp-rom5722-a1-lvds0-auo.dtb
    • g070vw01(LVDS1) + HDMI
      • imx8mp-rom5722-a1-lvds1-auo.dtb
    • g215hvn01(DUAL LVDS) + HDMI
      • imx8mp-rom5722-a1-lvds-dual.dtb
  • DSI
    • adv7535(DSI to HDMI) + HDMI
      • imx8mp-rom5722-a1-adv7535.dtb
    • auog101uan02(DSI) + HDMI
      • imx8mp-rom5722-a1-auog101uan02.dtb
• Camera
  • OV5640 (default)
    • imx8mp-rom5722-a1.dtb
  • Basler camrea
    • imx8mp-rom5722-a1-basler.dtb

ROM-3620

• Display
  • LVDS
    • g070vw01
      • imx8mxp-rom3620-a1.dtb
    • g150xgel05
      • imx8qxp-rom3620-a1-lvds-chimei.dtb
    • g215hvn01
      • imx8qxp-rom3620-a1-lvds-dual.dtb
  • DSI to HDMI
    • imx8qxp-rom3620-a1-hdmi-bridge.dtb
  • DSI
    • auog101uan02
      • imx8qxp-rom3620-a1-auog101uan02.dtb

RSB-3730

• Display
  • HDMI
    • imx8mm-rsb3730-a2.dtb
  • LVDS
    • g070vw01
      • imx8mm-rsb3730-a2-dsi2lvds-800x480.dtb
    • g215hv01
      • imx8mm-rsb3730-a2-dsi2lvds-1920x1080.dtb
  • DSI
    • g101uan2.0
      • imx8mm-rsb3730-a2-dsi-auog101uan02.dtb

Burn-in Test

About bottom board setting

The disable pin of PCIE

You should config disable pin follow your bottom board.

<syntaxhighlight lang="c">
&amp;pcie0{
        pinctrl-names = &quot;default&quot;;
        pinctrl-0 = &lt;&amp;pinctrl_pcie0&gt;;
        //disable-gpio = &lt;&amp;tca9538 0 GPIO_ACTIVE_LOW&gt;; &lt;---
        reset-gpio = &lt;&amp;gpio1 13 GPIO_ACTIVE_LOW&gt;;
        ext_osc = &lt;1&gt;;
        status = &quot;okay&quot;;
};
</syntaxhighlight>

Fix no sound issue probability when the HDMI plug in/out

You can use the following patch to fix this issue:

<a alt="<a alt="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" href="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" title="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch">http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch</a>" href="<a alt="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" href="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" title="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch">http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch</a>" title="<a alt="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" href="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch" title="http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch">http://ess-wiki.advantech.com.tw/wiki/images/5/59/0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch</a>">[0001-imx865-hdmi-enable-overflow-workaround-for-imx865-hd.patch</a>]

<syntaxhighlight lang="c">
From 9ca13642ff1367cb32c15f82d2c077f2f7c0e8f1 Mon Sep 17 00:00:00 2001
From: Sandor Yu &lt;Sandor.yu@nxp.com&gt;
Date: Mon, 25 Oct 2021 16:13:37 +0800
Subject: [PATCH] imx865: hdmi: enable overflow workaround for imx865 hdmi

Signed-off-by: Sandor Yu &lt;Sandor.yu@nxp.com&gt;
---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
index b48cdaa493b7..b53e2efed3bf 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -2220,6 +2220,7 @@ static void dw_hdmi_clear_overflow(struct dw_hdmi *hdmi)
 	case 0x201a:
 	case 0x211a:
 	case 0x212a:
+	case 0x213a:
 		count = 1;
 		break;
 	default:
-- 
2.17.1
</syntaxhighlight>

How to get the MAC, Serial Number, and Manufacture Date in the QSPI flash

MAC 0:

<syntaxhighlight lang="c">
READ_DATA=`dd if=/dev/mtdblock0 bs=1 skip=$((0xd0000)) count=6 2&gt; /dev/null | hexdump -e &#39;16/1 &quot;%02x &quot; &quot;\n&quot;&#39; | sed &#39;s/ /:/g&#39; | cut -c 1-17`
echo $READ_DATA
</syntaxhighlight>

MAC 1:

<syntaxhighlight lang="c">
READ_DATA=`dd if=/dev/mtdblock0 bs=1 skip=$((0xd0400)) count=6 2&gt; /dev/null | hexdump -e &#39;16/1 &quot;%02x &quot; &quot;\n&quot;&#39; | sed &#39;s/ /:/g&#39; | cut -c 1-17`
echo $READ_DATA
</syntaxhighlight>

Serial Number:

<syntaxhighlight lang="c">
READ_DATA=`dd if=/dev/mtdblock0 bs=1 skip=$((0xd0006)) count=10 2&gt; /dev/null | cut -c 1-10`
echo $READ_DATA
</syntaxhighlight>

Manufacture Date:

<syntaxhighlight lang="c">
READ_DATA=`dd if=/dev/mtdblock0 bs=1 skip=$((0xd0010)) count=14 2&gt; /dev/null | cut -c 1-14`
READ_DATA=`echo $READ_DATA | cut -c 1-4`-`echo $READ_DATA | cut -c 5-6`-`echo $READ_DATA | cut -c 7-8`_`echo $READ_DATA | cut -c 9-10`-`echo $READ_DATA | cut -c 11-12`-`echo $READ_DATA | cut -c 13-14`
echo $READ_DATA
</syntaxhighlight>