Difference between revisions of "ROM-2860 user guide"
| (42 intermediate revisions by the same user not shown) | |||
| Line 23: | Line 23: | ||
=== ''' ROM-ED 接口布局圖 Board Dimension Layout''' === | === ''' ROM-ED 接口布局圖 Board Dimension Layout''' === | ||
| + | |||
| + | [[File:ROM-2860 layout functions top s.PNG|RTENOTITLE]] | ||
| + | |||
| + | [[File:ROM-2860 layout functions buttom s.PNG|RTENOTITLE]] | ||
| + | |||
| + | [[File:ROM-2860 layout functions switchsetting ss.png|RTENOTITLE]] | ||
| | ||
| + | |||
| + | | ||
| + | |||
| + | '''SW1''' | ||
| + | |||
| + | *'''SW1(1-off,2-on) : eMMC boot''' | ||
| + | *'''SW1(1-on,2-on) : UFS boot''' | ||
| + | |||
| + | '''SW2''' | ||
| + | |||
| + | *'''SW2(1-on): Forced Recovery''' | ||
| + | *'''SW2(1-off): Normal Boot''' | ||
| + | *'''SW2(2-on): AT mode''' | ||
| + | *'''SW2(2-off):ATx mode''' | ||
| + | |||
| + | '''SW6''' | ||
=== '''主板内置插针式引脚排序方式 (Pin Header defination) ''' === | === '''主板内置插针式引脚排序方式 (Pin Header defination) ''' === | ||
| Line 51: | Line 73: | ||
| | ||
| − | + | == '''Recovery & Rescue 燒錄方法 (Recovery & Rescue method)''' == | |
'''1. Download the Qualcomm Software Center ''' | '''1. Download the Qualcomm Software Center ''' | ||
| − | ''' <span lang="EN-US" style="font-family:Aptos"> | + | ''' [https://softwarecenter.qualcomm.com/#/ <span lang="EN-US" style="font-family:Aptos">Qualcomm® Software Center</span>] ''' |
'''2. Open the Qualcomm Software Center ''' | '''2. Open the Qualcomm Software Center ''' | ||
| Line 101: | Line 123: | ||
'''13 Connect your device via Micro USB.''' | '''13 Connect your device via Micro USB.''' | ||
| − | ''' | + | === '''<u>Reformat</u> ''' === |
| + | |||
| + | '''<span style="background-color:#ffff00;">For confirmation, we will erase the partition before UFS and eMMC installation. </span>''' | ||
| + | |||
| + | '''1. Select provision button [[File:ROM-2860 provision file button.PNG|RTENOTITLE]] ''' | ||
| + | |||
| + | [[File:ROM-2860 provision file icon.PNG|RTENOTITLE]] | ||
| + | |||
| + | '''2. Add the prog_firehose_ddr.elf and provision_ufs31.xml in UFS folder. ''' | ||
| + | |||
| + | [[File:ROM-2860 provision file.PNG|RTENOTITLE]] | ||
| + | |||
| + | '''3. Then press "OK" , it will start to do USF Provision. ''' | ||
| − | + | [[File:ROM-2860 provision file running.PNG|RTENOTITLE]] | |
| − | ''' | + | '''4. When the Provision finished , you can see the result in message window. ''' |
| − | + | [[File:ROM-2860 provision file result.PNG|RTENOTITLE]] | |
| − | ''' | + | === '''<u>Flash UFS</u>''' === |
| + | |||
| + | ''' <span style="background-color:#ffff00;">1. Change the SW1 and SW2 </span>''' | ||
| + | |||
| + | '''<span style="background-color:#ffff00;"> Flash UFS: the SW1 switch to 1-on, 2-on Forced Recovery : The SW2 switch to 1-on ,2 - on . </span>''' | ||
| + | |||
| + | ''' 2. Turn on the power ''' | ||
| + | |||
| + | ''' 3. Open " PCATApp" Tool ''' | ||
| + | |||
| + | ''' 4. Click " Connect A Device" ''' | ||
[[File:ROM-2860 PCAT UFS .PNG|RTENOTITLE]] | [[File:ROM-2860 PCAT UFS .PNG|RTENOTITLE]] | ||
| − | ''' | + | '''5. Select "Qualcomm HS-USB QDLoader 9008 (COM6) ''' |
[[File:ROM-2860 PCAT Tool Select device.PNG|RTENOTITLE]] | [[File:ROM-2860 PCAT Tool Select device.PNG|RTENOTITLE]] | ||
| − | ''' | + | '''6. Click " Connect " device ''' |
[[File:ROM-2860 PCAT Tool Connect device.PNG|RTENOTITLE]] | [[File:ROM-2860 PCAT Tool Connect device.PNG|RTENOTITLE]] | ||
| − | ''' | + | '''7. When you connected successfully , it will show "qreen word" - Qualcomm HS-USB QDLoader 9008 (COM 6) ''' |
[[File:ROM-2860 PCAT UFS connectiondevice.PNG|RTENOTITLE]] | [[File:ROM-2860 PCAT UFS connectiondevice.PNG|RTENOTITLE]] | ||
| − | ''' | + | '''8. Select UFS Folder in PCAT Tool , the Tool will help load Files automatically and Select "MEMORY_TYPE_UFS" ''' |
| + | |||
| + | [[File:ROM-2860 PCAT Select UFS File .PNG|RTENOTITLE]] | ||
| + | |||
| + | '''9. Click " Download" ''' | ||
| + | |||
| + | [[File:ROM-2860 PCAT Select UFS File Download.png|RTENOTITLE]] | ||
| + | |||
| + | '''10. UFS Download Status ''' | ||
| + | |||
| + | '''[[File:ROM-2860 PCAT Select UFS File Download status.png|RTENOTITLE]]11. UFS Donwload compeleted ''' | ||
| + | |||
| + | '''[[File:ROM-2860 PCAT Select UFS File Download status 100.png|RTENOTITLE]]''' | ||
| + | |||
| + | === '''Flash eMMC''' === | ||
| + | |||
| + | '''1. Turn off the Power ''' | ||
| + | |||
| + | '''<span style="background-color:#ffff00;">2. Change the SW1 and SW2 </span>''' | ||
| + | |||
| + | '''<span style="background-color:#ffff00;"> Flash eMMC: the SW1 switch to 1-off, 2-on Forced Recovery : The SW2 switch to 1-on ,2 - on . </span>''' | ||
| + | |||
| + | '''3. Turn on the power ''' | ||
| + | |||
| + | '''4. Make sure the device connection status. ''' | ||
| + | |||
| + | '''5. If the device disconnect with PCAT Tool , please connect it again. ''' | ||
| + | |||
| + | [[File:ROM-2860 PCAT Tool Connect device.PNG|RTENOTITLE]] | ||
| + | |||
| + | '''6. Select eMMC Folder.''' | ||
| + | |||
| + | '''[[File:ROM-2860 PCAT Select eMMC File.png|RTENOTITLE]]7. Make sure the setting ,then press " Download " button.''' | ||
| + | |||
| + | [[File:ROM-2860 PCAT check eMMC setting download1.png|RTENOTITLE]] | ||
| + | |||
| + | ''' 8. eMMC downlaoad status ''' | ||
| + | |||
| + | [[File:ROM-2860 PCAT Select eMMC File Download status.png|RTENOTITLE]] | ||
| + | |||
| + | ''' 9. eMMC D''''''onwload compeleted ''' | ||
| + | |||
| + | [[File:ROM-2860 PCAT Select eMMC File Download status 100.png|RTENOTITLE]] | ||
| + | |||
| + | '''10. When the eMMC installation finished . Close the PCAT tool ,''' | ||
| + | |||
| + | '''11 pleaes remove the mirco usb cable, turn off the power ''' | ||
| + | |||
| + | '''12.''' '''eMMC boot up : SW1 switch to 1-off, 2-on Forced Recovery : <span style="background-color:#ffff00;"> The SW2 switch to 1-off ,2 - on . </span>''' | ||
| + | |||
| + | '''13. Connect debug cable and open the terminal , turn on the power . ''' | ||
| + | |||
| + | '''14. If you have done " <u>Reformat</u> " <u>,</u> the message will show " DDR: Start of DDR Training Init " ''' | ||
| + | |||
| + | '''15. When the systme boot up , you need to type " qcs6490-rom2860a1 login: <span style="background-color:#ffff33;">root </span>" , " Password: <span style="background-color:#ffff00;">oelinux123</span>"''' | ||
| + | |||
| + | '''16. After type the long in and password , and you also can chek the image information about date , kernel version etc.. ''' | ||
| + | |||
| + | '''[[File:ROM-2860 login system.PNG|RTENOTITLE]]''' | ||
| + | |||
| + | == '''Fastboot''' == | ||
| + | |||
| + | *Micro USB: ROM-ED92 USB0 | ||
| + | |||
| + | Connect the ROM-ED92 USB0 to host computer and set the Micro USB to '''peripheral''' mode. | ||
| + | <pre># echo "peripheral" > /sys/devices/platform/soc/a600000.ssusb/mode</pre> | ||
| + | |||
| + | | ||
| + | |||
| + | === '''Enter the fastboot mode''' === | ||
| + | <pre>adv@adv-desktop:~$ adb devices | ||
| + | List of devices attached | ||
| + | 2e8c656e device | ||
| + | |||
| + | adv@adv-desktop:~$ adb root | ||
| + | restarting adbd as root | ||
| + | |||
| + | adv@adv-desktop:~$ adb reboot bootloader | ||
| + | |||
| + | adv@adv-desktop:~$ fastboot devices | ||
| + | 2e8c656e fastboot</pre> | ||
| + | |||
| + | | ||
| + | |||
| + | === '''Use the fastboot to flash the kernel boot image''' === | ||
| + | <pre>adv@adv-desktop:~$ fastboot flash boot_a qti-ubuntu-robotics-image-qcs6490-odk-boot.img | ||
| + | target reported max download size of 805306368 bytes | ||
| + | sending 'boot_a' (24420 KB)... | ||
| + | OKAY [ 0.790s] | ||
| + | writing 'boot_a'... | ||
| + | OKAY [ 0.144s] | ||
| + | finished. total time: 0.935s | ||
| + | |||
| + | adv@adv-desktop:~$ fastboot flash boot_b qti-ubuntu-robotics-image-qcs6490-odk-boot.img | ||
| + | target reported max download size of 805306368 bytes | ||
| + | sending 'boot_b' (24420 KB)... | ||
| + | OKAY [ 0.827s] | ||
| + | writing 'boot_b'... | ||
| + | OKAY [ 0.133s] | ||
| + | finished. total time: 0.960s</pre> | ||
| | ||
| − | = | + | === '''Use the fastboot to flash the kernel dtbo image''' === |
| + | <pre>adv@adv-desktop4:~$ fastboot flash dtbo_a dtbo.img | ||
| + | target reported max download size of 805306368 bytes | ||
| + | sending 'dtbo_a' (12330 KB)... | ||
| + | OKAY [ 0.427s] | ||
| + | writing 'dtbo_a'... | ||
| + | OKAY [ 0.070s] | ||
| + | finished. total time: 0.497s | ||
| + | |||
| + | adv@adv-desktop4:~$ fastboot flash dtbo_b dtbo.img | ||
| + | target reported max download size of 805306368 bytes | ||
| + | sending 'dtbo_b' (12330 KB)... | ||
| + | OKAY [ 0.422s] | ||
| + | writing 'dtbo_b'... | ||
| + | OKAY [ 0.061s] | ||
| + | finished. total time: 0.483s</pre> | ||
= '''通用方法(General Method)''' = | = '''通用方法(General Method)''' = | ||
| Line 146: | Line 304: | ||
=== [https://ess-wiki.advantech.com.tw/view/AIM-Linux/BSP/Qualcomm/RISC_QCS_Linux_00011.1_qualcomm_series '''Ubuntu 20.04'''] === | === [https://ess-wiki.advantech.com.tw/view/AIM-Linux/BSP/Qualcomm/RISC_QCS_Linux_00011.1_qualcomm_series '''Ubuntu 20.04'''] === | ||
| − | <div id="gtx-trans" style="position: absolute; left: | + | <div id="gtx-trans" style="position: absolute; left: 187px; top: 2388.6px;"><div class="gtx-trans-icon"> </div> </div> |
Latest revision as of 07:34, 5 September 2024
Contents
產品介紹
產品特性(Features)
- Qualcomm Arm® v8 Cortex® Gold plus up to 2.7 GHz
- 3x Arm v8 Cortex® Up to 2.4GHz
- Onboard LPDDR5 8GB, 8533MT/s memory
- 1x MIPI-DSI x4, 1x DP and 1x eDP1.4 for Displays
- 1x USB3.2 Gen1, 1x USB2.0, 2x PCIe Gen3.0 x1, 2x I2S, 2x 4wire UART, 1x SPI,16x GPIO, 2x I2C, 6x PWM, 2x MIPI-CSI x4
- 1x UFS, 1x eMMC and 1x 4-bit SDIO for storages
- Support Windows 11 and Ubuntu
產品官網連結(Product information Link)
ROM-2860
接口布局和尺寸(Layout and Sizes)
ROM-ED 接口布局圖 Board Dimension Layout
SW1
- SW1(1-off,2-on) : eMMC boot
- SW1(1-on,2-on) : UFS boot
SW2
- SW2(1-on): Forced Recovery
- SW2(1-off): Normal Boot
- SW2(2-on): AT mode
- SW2(2-off):ATx mode
SW6
主板内置插针式引脚排序方式 (Pin Header defination)
Internal I/O, Jummper/Switch List:
| Position | Description |
快速入門 (Quick Start)
系统下载 (OS Download)
- 'Linux系统 (Linux OS)'
Ubuntu 20.04 :
Recovery & Rescue 燒錄方法 (Recovery & Rescue method)
1. Download the Qualcomm Software Center
2. Open the Qualcomm Software Center
3. Search "PCAT" in the search bar
4. Click Qualcomm® Product Configuration Assistant Tool
5. Select Qualcomm® Product Configuration Assistant Tool version
Version: 2.33.2.119
6. Install Qualcomm® Product Configuration Assistant Tool 2.33.2.119
7. Search "QUTS" in the search bar
8. Click the Qualcomm® Unified Tools Services
9. Select Qualcomm® Unified Tools Services version
Version : 1.75.2.9
10. Install Qualcomm® Unified Tools Services 1.75.2.9
11. You will find the new application in your Windows system .
12. Unzip the UFS File and eMMC File
For example :
2860A1AIM37UIV10084_2024-08-08_ufs_debug.tgz
2860A1AIM37UIV10084_2024-08-08_emmc_debug.tgz
13 Connect your device via Micro USB.
Reformat
For confirmation, we will erase the partition before UFS and eMMC installation.
1. Select provision button 
2. Add the prog_firehose_ddr.elf and provision_ufs31.xml in UFS folder.
3. Then press "OK" , it will start to do USF Provision.
4. When the Provision finished , you can see the result in message window.
Flash UFS
1. Change the SW1 and SW2
Flash UFS: the SW1 switch to 1-on, 2-on Forced Recovery : The SW2 switch to 1-on ,2 - on .
2. Turn on the power
3. Open " PCATApp" Tool
4. Click " Connect A Device"
5. Select "Qualcomm HS-USB QDLoader 9008 (COM6)
6. Click " Connect " device
7. When you connected successfully , it will show "qreen word" - Qualcomm HS-USB QDLoader 9008 (COM 6)
8. Select UFS Folder in PCAT Tool , the Tool will help load Files automatically and Select "MEMORY_TYPE_UFS"
9. Click " Download"
10. UFS Download Status
11. UFS Donwload compeleted
Flash eMMC
1. Turn off the Power
2. Change the SW1 and SW2
Flash eMMC: the SW1 switch to 1-off, 2-on Forced Recovery : The SW2 switch to 1-on ,2 - on .
3. Turn on the power
4. Make sure the device connection status.
5. If the device disconnect with PCAT Tool , please connect it again.
6. Select eMMC Folder.
7. Make sure the setting ,then press " Download " button.
8. eMMC downlaoad status
' 9. eMMC D'onwload compeleted
10. When the eMMC installation finished . Close the PCAT tool ,
11 pleaes remove the mirco usb cable, turn off the power
12. eMMC boot up : SW1 switch to 1-off, 2-on Forced Recovery : The SW2 switch to 1-off ,2 - on .
13. Connect debug cable and open the terminal , turn on the power .
14. If you have done " Reformat " , the message will show " DDR: Start of DDR Training Init "
15. When the systme boot up , you need to type " qcs6490-rom2860a1 login: root " , " Password: oelinux123"
16. After type the long in and password , and you also can chek the image information about date , kernel version etc..
Fastboot
- Micro USB: ROM-ED92 USB0
Connect the ROM-ED92 USB0 to host computer and set the Micro USB to peripheral mode.
# echo "peripheral" > /sys/devices/platform/soc/a600000.ssusb/mode
Enter the fastboot mode
adv@adv-desktop:~$ adb devices List of devices attached 2e8c656e device adv@adv-desktop:~$ adb root restarting adbd as root adv@adv-desktop:~$ adb reboot bootloader adv@adv-desktop:~$ fastboot devices 2e8c656e fastboot
Use the fastboot to flash the kernel boot image
adv@adv-desktop:~$ fastboot flash boot_a qti-ubuntu-robotics-image-qcs6490-odk-boot.img target reported max download size of 805306368 bytes sending 'boot_a' (24420 KB)... OKAY [ 0.790s] writing 'boot_a'... OKAY [ 0.144s] finished. total time: 0.935s adv@adv-desktop:~$ fastboot flash boot_b qti-ubuntu-robotics-image-qcs6490-odk-boot.img target reported max download size of 805306368 bytes sending 'boot_b' (24420 KB)... OKAY [ 0.827s] writing 'boot_b'... OKAY [ 0.133s] finished. total time: 0.960s
Use the fastboot to flash the kernel dtbo image
adv@adv-desktop4:~$ fastboot flash dtbo_a dtbo.img target reported max download size of 805306368 bytes sending 'dtbo_a' (12330 KB)... OKAY [ 0.427s] writing 'dtbo_a'... OKAY [ 0.070s] finished. total time: 0.497s adv@adv-desktop4:~$ fastboot flash dtbo_b dtbo.img target reported max download size of 805306368 bytes sending 'dtbo_b' (12330 KB)... OKAY [ 0.422s] writing 'dtbo_b'... OKAY [ 0.061s] finished. total time: 0.483s
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
查看内存容量(Check Memory Capacity)
查看存储容量(Check Storage Capacity)
設置RTC (RTC Setting)
查看系統時間 (Check the system)