Difference between revisions of "RSB-3430 user guide"

From ESS-WIKI
Jump to: navigation, search
 
(34 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
== '''資源特性(Features)''' ==
 
  
−
*NXP Arm® Cortex®-A53 i.MX8M Plus Quad/Dual up to 1.8 GHz
+
== '''產品介紹(Product introduction )''' ==
−
*Onboard LPDDR4 4 GB / 6 GB, 4000MT/s memory
 
−
*HDMI 1920x1080 at 60Hz, 1 Single or 1 Dual Channel 24 bit LVDS (or 1 4-Lane MIPI-DSI by BOM Option)
 
−
*1 4-wire RS-232/422/485, 1 USB3.2 Gen1 By 1, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
 
−
*1 mini-PCIe for 3G/4G, 1 M.2 2230 Key E Slot
 
−
*Supports Yocto Linux and Android
 
−
*Support I/O Expansions boards by UIO40-Express
 
  
−
== '''訂購資訊(Ordering Information)''' ==
+
=== '''產品特性(Product Features)''' ===
  
−
[[File:RSB-3720 ordinfo 2021-10-21 143630.jpg|RTENOTITLE]]
+
*NXP Arm® Cortex®-A53 i.MX8M Plus Quad/Dual up to 1.8 GHz
 +
*Onboard LPDDR4 4 GB / 6 GB, 4000MT/s memory
 +
*HDMI 1920x1080 at 60Hz, 1 Single or 1 Dual Channel 24 bit LVDS (or 1 4-Lane MIPI-DSI by BOM Option)
 +
*1 4-wire RS-232/422/485, 1 USB3.2 Gen1 By 1, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
 +
*1 mini-PCIe for 3G/4G, 1 M.2 2230 Key E Slot
 +
*Supports Yocto Linux and Android
 +
*Support I/O Expansions boards by UIO40-Express
  
−
== '''规格（Specifications）''' ==
+
 
  
−
== '''接口布局和尺寸(Layout and Sizes)''' ==
+
=== '''產品官網連結(Product official website link) ''' ===
 +
 
 +
[https://www.advantech.com/zh-tw/products/5912096e-f242-4b17-993a-1acdcaada6f6/rsb-3430/mod_05e3a6de-5d7f-4f64-9884-75fb4c4d87d9 '''RSB-3430''']
 +
 
 +
== '''硬件接口說明(Hardware interface introduction)''' ==
 +
 
 +
=== '''接口布局和尺寸(Layout and Sizes)''' ===
  
 
=== '''接口布局圖 Board Dimension Layout ''' ===
 
=== '''接口布局圖 Board Dimension Layout ''' ===
  
−
[[File:RSB-3720 board review2021-10-21 144120.jpg|RTENOTITLE]]
+
[[File:RSB-3430 Board outline.PNG|RTENOTITLE]]
 +
 
 +
 
  
−
[[File:RSB-3720 connector location 2021-10-21 143853.jpg|RTENOTITLE]]
+
[[File:RSB-3430 IOoutline.PNG|RTENOTITLE]]
  
 +
''' 机械尺寸  ('''Mechanical Characteristics)
  
 +
[[File:RSB-3430 Board Drawing.PNG|RTENOTITLE]]
  
−
[[File:RSB-3720 connector location back 2021-10-21 144716.jpg|RTENOTITLE]]
+
[[File:RSB-3430 Board Drawing 1.PNG|RTENOTITLE]]
  
 +
 
  
 +
==  '''Connector List''' ==
  
−
== ''' ''''''Connector List''' ==
+
[[File:RSB-3430 connect list.PNG|RTENOTITLE]]
  
−
{| border="1" cellspacing="1" cellpadding="1"
+
 
−
|-
 
−
| BAT
 
−
| RTC Battery Connector
 
−
|-
 
−
| BL1
 
−
| LVDS Backlight 1 
 
−
|-
 
−
| BL2
 
−
| LVDS Backlight 2 
 
−
|-
 
−
| COM1 
 
−
| COM + CAN Pin Header (default as debug console) 
 
−
|-
 
−
| CSI1
 
−
| MIPI-CSI Camera Input 1
 
−
|-
 
−
| CSI2
 
−
| MIPI-CSI Camera Input 2 
 
−
|-
 
−
| DCIN/DCIN 1
 
−
| 12V DC Power Inout by DC Jack / by Pin Header 
 
−
|-
 
−
| HDMI 
 
−
| HDMI CONN
 
−
|-
 
−
| LAN1
 
−
| Ethernet 1 
 
−
|-
 
−
| LAN2 
 
−
| Ethernet 2
 
−
|-
 
−
| LOUT
 
−
| Line Out Pin Header
 
−
|-
 
−
| LVDS
 
−
| LVDS CONN.
 
−
|-
 
−
| M2
 
−
| M.2 Key E CONN.
 
−
|-
 
−
| MIC
 
−
| MIC In Pin Header
 
−
|-
 
−
| MPCIE
 
−
| Mini-PCIe CONN.
 
−
|-
 
−
| RST
 
−
| Rest Button
 
−
|-
 
−
| SD
 
−
| SD Slot
 
−
|-
 
−
| UIO1 
 
−
| UIO40-Express Pin Header 1 
 
−
|-
 
−
| UIO2 
 
−
| UIO40-Express Pin Header 2 
 
−
|-
 
−
| USB1
 
−
| USB CONN. (USB 3.2 Gen 1 on TOP + USB 2.0 on BOT)<br/>
 
−
|}
 
  
 
=== '''接口引脚定義 (Pin definitions)''' ===
 
=== '''接口引脚定義 (Pin definitions)''' ===
  
−
*[[BLP1|BLP1&nbsp;]]
+
[[RSB-3430_RTC_BAT|RTC_BAT]]
−
*[[BLP2|BLP2]]
+
 
−
*[[VDD1|VDD1]]
+
[[RSB-3430_DCIN|DCIN]]
−
*[[SW1|SW1]]
+
 
−
*[[BAT_(RTC_Battery_CONN.)|BAT (RTC Battery CONN.)]]
+
[[RSB-3430_COM|COM]]
−
*[[BL1_(LVDS_Backlight_1)|BL1 (LVDS Backlight 1)]]
+
 
−
*[[BL2_(LVDS_Backlight_2)|BL2 (LVDS Backlight 2)]]
+
[[RSB-3430_HDMI|HDMI]]
−
*[[COM1_(COM_+_CAN_Pin_Header):_(default_as_debug_console)|COM1 (COM + CAN Pin Header): (default as debug console)]]
+
 
−
*[[CSI1_(MIPI-CSI_Camera_Input_1)|CSI1 (MIPI-CSI Camera Input 1)]]
+
[[RSB-3430_USB|USB]]
−
*[[CSI2_(MIPI-CSI_Camera_Input_2)|CSI2 (MIPI-CSI Camera Input 2)]]
+
 
−
*[[DCIN/_DCIN1_(12V_DC_Power_Input_by_DC_Jack/_by_Pin_Header)|DCIN/ DCIN1 (12V DC Power Input by DC Jack/ by Pin Header)]]
+
[[RSB-3430_M2|M2]]
−
*[[HDMI_(HDMI_CONN.)|HDMI (HDMI CONN.)]]
+
 
−
*[[LAN1_(Ethernet_eth0)|LAN1 (Ethernet eth0)]]
+
[[RSB-3430_MiniPCIe|MiniPCIe]]
−
*[[LAN2_(Ethernet_eth1)|LAN2 (Ethernet eth1)]]
+
 
−
*[[LOUT_(Line_Out_Pin_Header)|LOUT (Line Out Pin Header)]]
+
[[RSB-3430_LVDS_BKLT_PWR|LVDS_BKLT_PWR]]
−
*[[LVDS_(LVDS_CONN.)|LVDS (LVDS CONN.)]]
+
 
−
*[[M2_(M.2_Key_E_CONN.)|M2 (M.2 Key E CONN.)]]
+
[[RSB-3430_Backlight_Voltage|Backlight Voltage&nbsp;]]
−
*[[MIC_(MIC_In_Pin_Header)|MIC (MIC In Pin Header)]]
+
 
−
*[[MPCIE_(Mini-PCIe_CONN.)|MPCIE (Mini-PCIe CONN.)]]
+
[[RSB-3430_H4|H4]]
−
*[[RST_(Reset_Button)|RST (Reset Button)]]
+
 
−
*[[SD_(SD_Slot)|SD (SD Slot)]]
+
[[RSB-3430_CN1|CN1]]
−
*[[SIM_(SIM_Slot)|SIM (SIM Slot)]]
+
 
−
*[[UIO1_(UIO40-Express_Pin_Header_1)|UIO1 (UIO40-Express Pin Header 1)]]
+
[[RSB-3430_CN2|CN2]]
−
*[[UIO2_(UIO40-Express_Pin_Header_2)|UIO2 (UIO40-Express Pin Header 2)]]
+
 
−
*[[USB_1_(USB_3.2_Gen_1_on_TOP_+_USB_2.0_on_BOT)|USB 1 (USB 3.2 Gen 1 on TOP + USB 2.0 on BOT)]]
+
[[RSB-3430_LVDS|LVDS]]
−
*[[LED|LED]]
 
  
−
=== '''&nbsp;机械尺寸&nbsp; ('''Mechanical Characteristics) ===
+
[[RSB-3430_SD|SD]]
  
−
[[File:RSB-3720 board Dimensions 2021-10-21 145827.jpg|RTENOTITLE]]
+
[[RSB-3430_SIM_Slot|SIM_Slot]]
  
 
== '''快速入门 (Quick Start)''' ==
 
== '''快速入门 (Quick Start)''' ==
Line 131: Line 80:
 
=== '''系统下载 (OS Download)''' ===
 
=== '''系统下载 (OS Download)''' ===
  
−
'''Linux系统 (Linux OS)''''''&nbsp; &nbsp;'''
+
*'''Linux系统 (Linux OS)'''  
 +
**'''[https://pan.baidu.com/s/1fP5BGOOiDv5qV-3oTQmyow Baidu link for imx6 Yocto 2.5 BSP and Image]&nbsp;Password：ra18'''
 +
**'''[https://www.dropbox.com/sh/910ji9j8p2u1s52/AACSUfK4JFXRT5gDi1Od8V07a?dl=0 Dropbox link for imx6 Yocto 2.5 BSP and Image]'''
 +
**[https://www.dropbox.com/sh/910ji9j8p2u1s52/AACSUfK4JFXRT5gDi1Od8V07a?dl=0&lst=&preview=downloads_imx6-2.5.tgz '''Downloads 2.5'''] 
 +
 
 +
&nbsp; &nbsp;
 +
 
 +
== '''&nbsp;Linux&nbsp;燒錄方法 (Linux Flash eMMC Method)''' ==
 +
 
 +
'''1. 確認SD 在Ubuntu 電腦中的代號'''
 +
 
 +
'''[[File:RSB-3430 Check SDCard 2021-10-26 134232.jpg|RTENOTITLE]]'''
 +
 
 +
'''[[File:RSB-3430 SDCardInfo 2021-10-26 134323.jpg|RTENOTITLE]]'''
 +
 
 +
'''2. 先將鏡像燒錄到SD Card 中( Create a bootable SD card )&nbsp;'''
 +
 
 +
'''[[File:RSB-3430 dd SDcard 2021-10-26 134535.jpg|RTENOTITLE]]''
 +
 
 +
&nbsp;
 +
 
 +
&nbsp;
 +
 
 +
'''[[File:RSB-3430 SDCard info 2 2021-10-26 134939.jpg|RTENOTITLE]]'''
 +
 
 +
'''3.設定終端機(Set Debug Terminal)&nbsp;'''
 +
 
 +
Debug 串口調試 (Debug port Setting)
 +
 
 +
以 Tera Term&nbsp;&nbsp;为例介绍如何使用串口调试功能
 +
<pre>  Baud Rate波特率：115200
 +
  Data 数据位：8
 +
  Parity 奇偶校验：无
 +
&nbsp;  Stop 停止位：1
 +
  Flow Control流控：无</pre>
 +
 
 +
:&nbsp;
 +
 
 +
Tera Term Tool&nbsp;
 +
 
 +
[[File:TeraTerm 2021-09-10 140930n.jpg|RTENOTITLE]]
 +
 
 +
[[File:TeraTerm12021-09-10 141114n.jpg|RTENOTITLE]]
 +
 
 +
Check the Sriel port in Device Manager (查看PC端的串口号)：
 +
 
 +
if you can not identify the Serial device , please check your serial driver.&nbsp;
  
−
{| cellspacing="0" cellpadding="0" border="1"
+
[[File:COMportinx862021-09-10 141610.jpg|RTENOTITLE]]
−
|-
 
−
|  
 
−
'''Git BSP Tag Version'''
 
  
−
|
+
'''4. 將SD card 插入機器&nbsp;'''
−
'''Product'''
 
  
−
| &nbsp;'''BSP/Image'''
+
&nbsp;&nbsp;[[File:RSB-3430 plugSD Card3 24240133.jpg|RTENOTITLE]]
−
|  
 
−
'''Date'''
 
  
−
|
+
'''5. 檢查撥碼開關&nbsp; ( 1 ON , 2 OFF)&nbsp;'''
−
'''Alpha Release'''
 
  
−
|
+
'''[[File:RSB-3430 Switch 24240134.jpg|RTENOTITLE]]'''
−
'''Beta Release'''
 
  
−
|
+
'''6. 接上Debug Cable&nbsp;'''
−
'''MP Release'''
 
  
−
|  
+
[[File:RSB-3430 Debug port 24240136.jpg|RTENOTITLE]]
−
'''Release Note'''
 
  
−
|
+
'''7. 打開電源&nbsp;'''
−
'''Comment'''
 
  
−
|  
+
[[File:RSB-3430 turnonpower 24240137.jpg|RTENOTITLE]]
−
'''Release Owner'''
 
  
−
|-
+
'''8. 由終端機進入系統&nbsp;'''
−
| style="text-align: center;" | imx6LBV90146<br/>
 
−
| RSB-3430A1
 
−
| &nbsp;3430A1AIM20LIV90146_DualQuad_2021-08-08.img.gz
 
−
| 2021-08-08
 
−
| style="text-align: center;" | V
 
−
|
 
−
|
 
−
|
 
−
|
 
−
|
 
−
|}
 
  
 +
'''[[File:RSB-3430 Debug terminal 2021-10-26 141124.jpg|RTENOTITLE]]'''
  
 +
'''9. 燒錄鏡像到 eMMC flash&nbsp;'''
  
−
*'''[https://pan.baidu.com/s/1fP5BGOOiDv5qV-3oTQmyow Baidu link for imx6 Yocto 2.5 BSP and Image]&nbsp;Password：ra18'''
+
'''將3430A1AIM20LIV90146_DualQuad_flash_tool.tgz 複製到U盤中,插入機器的USB Port&nbsp;'''
−
*'''[https://www.dropbox.com/sh/910ji9j8p2u1s52/AACSUfK4JFXRT5gDi1Od8V07a?dl=0 Dropbox link for imx6 Yocto 2.5 BSP and Image]'''
 
−
*[https://www.dropbox.com/sh/910ji9j8p2u1s52/AACSUfK4JFXRT5gDi1Od8V07a?dl=0&lst=&preview=downloads_imx6-2.5.tgz '''Downloads 2.5''']
 
  
−
&nbsp; &nbsp;
+
'''[[File:RSB-3430 Cpfile toUsb 2021-10-26 141813.jpg|RTENOTITLE]]'''
  
−
== '''&nbsp;Linux&nbsp;燒錄方法 (Linux Flash eMMC Method)''' ==
+
'''在系統中 ,確認USB中燒錄資料&nbsp;'''
  
−
== '''&nbsp;''' ==
+
'''[[File:RSB-3430 USB IN Device 2021-10-26 142038.jpg|RTENOTITLE]]'''
  
−
== '''Linux系统的基本使用(Linux&nbsp;System Basic Operating Method)''' ==
+
[[File:RSB-3430 CP file into root 2021-10-26 143316.jpg|RTENOTITLE]]
  
−
=== '''&nbsp; &nbsp; &nbsp; Display Setting (RSB-3430)''' ===
+
'''在根目錄下 ,解壓縮&nbsp;'''
  
−
'''&nbsp; &nbsp;'''
+
[[File:RSB-3430 Unzip file in root 2021-10-26 143506.jpg|RTENOTITLE]]
  
−
=== '''乙太網路使用方法(Ethernent Testing Method)''' ===
+
'''在mk_Inand 資料夾中執行 ./mksd-linux.sh&nbsp;'''
  
−
'''Command&nbsp;: ifconfig&nbsp;'''
+
[[File:RSB-3430 check file 2021-10-26 143952.jpg|RTENOTITLE]]
  
−
'''[[File:Ethernet Test 2021-09-09 131742.jpg|RTENOTITLE]]'''
+
[[File:RSB-3430 mksd linuxsh 2021-10-26 143855.jpg|RTENOTITLE]]
  
−
'''Command: Ping - I eth1 8.8.8.8&nbsp; or Ping - I eth0 8.8.8.8&nbsp;&nbsp;'''
+
[[File:RSB-3430 flash image done 2021-10-26 144801.jpg|RTENOTITLE]]
  
−
'''[[File:PingTest2021-09-09 131931.jpg|RTENOTITLE]]'''
+
'''10. 移除SD 卡,從eMMC 開機.&nbsp;'''
  
−
=== '''WiFi使用方法(WIFI Testing Method)''' ===
+
[[File:RSB-3430 boot from eMMC 2021-10-27 091349.jpg|RTENOTITLE]]
−
<pre>Command&nbsp;:  
 
  
−
# killall wpa_supplicant
+
== '''&nbsp;Linux系统的基本使用(Linux&nbsp;System Basic Operating Method)''' ==
−
# ifconfig wlan0 up
 
−
# wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf
 
−
# wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
 
−
# udhcpc -b -i wlan0'''
 
  
−
ping 8.8.8.8
+
=== '''載入預設值由uboot 設定(Load Default Setting in Uboot )''' ===
−
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
 
−
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
 
−
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre>
 
  
−
[[File:WifiTest 2021-09-09 132238.jpg|RTENOTITLE]]
+
'''1. 開機時 在五秒內按下空白鍵 ,進入Uboot&nbsp;'''
  
−
=== '''4G使用方法(4G Testing Method)''' ===
+
'''2. Command&nbsp;:&nbsp;'''
−
<pre>Command:
 
−
Test 4G: (EWM-C117FL06E - USB)
 
−
Step 1: Connect EWM-C117FL06E to Mini PCIE slot on 9680015491 and connect
 
−
the card to CN6 PCIe_D slot on ROM-DB5901.
 
−
Step 2: Connect the antenna 1750007990-01 to the SMA (F) connector on
 
−
9680015491
 
−
and connect the IPEX connector to MT1 on EWM-C117FL06E module.
 
−
Step 3: Connect the Mini USB cable from 9680015491 to USB 2.0 Type A port on
 
−
ROM-DB5901.
 
−
Step 4: Power on and execute the pppd command to connect to the network.
 
−
</pre>
 
  
−
[[File:4GTest2021-09-09 133204.jpg|RTENOTITLE]]
+
'''&nbsp; &nbsp; env default -a&nbsp;'''
  
−
[[File:4GTest12021-09-09 133648.jpg|RTENOTITLE]]
+
'''&nbsp; &nbsp; saveenv&nbsp;'''
  
−
=== '''GPIO使用方法(GPIO Operating Method)''' ===
+
'''&nbsp; &nbsp; reset&nbsp; &nbsp;'''
  
−
[[File:GPIOpin2021-09-11 143437.jpg|RTENOTITLE]]
+
'''[[File:RSB-3430 Load default 2021-10-27 091752.jpg|RTENOTITLE]]'''
  
 +
=== '''顯示設定 (Display&nbsp; Setting )&nbsp;''' ===
  
−
<pre>Loop-back Test (Take GPIO4 and GPIO5 as examples) 
+
'''&nbsp;預設值為: HDMI 輸出'''
  
−
Step 1: Connect GPIO4 and GPIO5
+
'''[[File:RSB-3420 uboot default 2021-10-27 135059.jpg|RTENOTITLE]]'''
−
Step 2: Export GPIO interface
 
  
−
root@imx8qxprom5620a1&nbsp;: ~# echo 456 > /sys/class/gpio/export
+
[[File:RSB-3430 uboot default 2 2021-10-27 135218.jpg|RTENOTITLE]]
−
root@imx8qxprom5620a1&nbsp;: ~# echo 452 > /sys/class/gpio/export
 
  
−
Step 3: Set direction
+
=== '''乙太網路使用方法(Ethernent Testing Method)''' ===
  
−
root@imx8qxprom5620a1&nbsp;: ~# echo out > /sys/class/gpio/gpio1/direction
+
'''Command&nbsp;: ifconfig&nbsp;'''
−
root@imx8qxprom5620a1&nbsp;: ~# echo in > /sys/class/gpio/gpio2/direction
 
  
−
Step 4: Read value and set output value then check
+
[[File:RSB-3430 ifconfig info 2021-10-27 092342.jpg|RTENOTITLE]]
  
−
root@imx8qxprom5620a1&nbsp;: ~# cat /sys/class/gpio/gpio2/value
+
'''Command: Ping 8.8.8.8&nbsp;'''
−
0r
 
−
oot@imx8qxprom5620a1&nbsp;: ~# echo 1 > /sys/class/gpio/gpio1/value
 
−
root@imx8qxprom5620a1&nbsp;: ~# cat /sys/class/gpio/gpio2/value
 
−
1</pre>
 
  
−
=== '''串口使用方法(Serial Port Operating&nbsp;Method)''' ===
+
'''[[File:RSB-3430 ping 8888 2021-10-27 092542.jpg|RTENOTITLE]]'''
  
−
RS-232 Test&nbsp;
+
&nbsp;
  
−
SW7 Setting (SW7設置)&nbsp;
+
=== '''WiFi & BT 使用方法(WIFI & Bluetooth&nbsp;Testing Method)''' ===
 +
<pre>M.2 module (EWM-W162M201E) - WIFI / BT Function&nbsp;
 +
WIFI&nbsp;
  
−
[[File:SW6&7settingn.jpeg|RTENOTITLE]]
+
$ ifconfig mlan0 up
 +
$ wpa_passphrase ${SSID} ${WPA_KEY} > /tmp/wpa.conf
 +
$ wpa_supplicant -BDwext -imlan0 -c/tmp/wpa.conf
 +
$ udhcpc -b -i mlan0
  
−
=== '''蓝牙使用方法(BlueTooth Operating&nbsp;Method)''' ===
+
BlueTooth&nbsp;
−
<pre>Command&nbsp;:
 
  
 +
$ /usr/libexec/bluetooth/bluetoothd -C &
 
$ hciconfig hci0 up
 
$ hciconfig hci0 up
 
$ bluetoothctl
 
$ bluetoothctl
Line 279: Line 231:
 
$ pairable on
 
$ pairable on
 
$ scan on
 
$ scan on
−
[NEW] FC:18:3C:8D:75:F4 myphone
+
[NEW] FC:18:3C:8D:75:F4 Device ID&nbsp;
 
$ scan off
 
$ scan off
 
$ pair FC:18:3C:8D:75:F4
 
$ pair FC:18:3C:8D:75:F4
−
$ connect FC:18:3C:8D:75:F4</pre>
+
$ connect FC:18:3C:8D:75:F4
 +
</pre>
 +
 
 +
&nbsp;
 +
 
 +
=== '''3G使用方法(3G Testing Method)''' ===
 +
<pre>Command:
 +
3G (Telit HE910D)&nbsp;
 +
pppd connect 'chat -v -s -t 10 "" "AT" "" "ATDT*99#" "CONNECT" ""' user username password password /dev/ttyACM3 460800 nodetach crtscts debug usepeerdns defaultroute &&nbsp;
 +
</pre>
 +
 
 +
=== '''USB 測試方式(USB Test metod )''' ===
 +
 
 +
USB&nbsp;
 +
 
 +
Insert a USB disk
 +
 
 +
usb 1-1.2: new high-speed USB device number 4 using ci_hdrc<br/> usb-storage 1-1.2:1.0: USB Mass Storage device detected<br/> scsi2&nbsp;: usb-storage 1-1.2:1.0<br/> scsi 2:0:0:0: Direct-Access &nbsp; &nbsp; Generic- SD/MMC &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 1.00 PQ: 0 ANSI: 0 CCS<br/> sd 2:0:0:0: [sda] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB)<br/> sd 2:0:0:0: [sda] Write Protect is off<br/> sd 2:0:0:0: [sda] No Caching mode page found<br/> sd 2:0:0:0: [sda] Assuming drive cache: write through<br/> sd 2:0:0:0: [sda] No Caching mode page found<br/> sd 2:0:0:0: [sda] Assuming drive cache: write through<br/> sda: sda1<br/> sd 2:0:0:0: [sda] No Caching mode page found<br/> sd 2:0:0:0: [sda] Assuming drive cache: write through<br/> sd 2:0:0:0: [sda] Attached SCSI removable disk
 +
 
 +
=== '''串口使用方法(Serial Port Operating&nbsp;Method)''' ===
 +
 
 +
'''RS-232 Test&nbsp;'''
 +
<pre>Command&nbsp;: stty -F /dev/ttymxc1 115200
 +
          echo Serial Port Test > /dev/ttymxc1</pre>
 +
 
 +
<br/> '''RS-422 setting'''
 +
<pre>echo 134 > /sys/class/gpio/export
 +
echo 135 > /sys/class/gpio/export
 +
echo out > /sys/class/gpio/gpio1/direction
 +
echo out > /sys/class/gpio/gpio2/direction
 +
echo 1 > /sys/class/gpio/gpio1/value
 +
echo 1 > /sys/class/gpio/gpio2/value </pre>
 +
 
 +
'''RS-422 test&nbsp;'''
 +
<pre>Command&nbsp;: stty -F /dev/ttymxc1 115200
 +
          echo Serial Port Test > /dev/ttymxc1</pre>
 +
 
 +
'''RS-485 setting&nbsp;'''
 +
<pre>echo 134 > /sys/class/gpio/export
 +
echo 135 > /sys/class/gpio/export
 +
echo out > /sys/class/gpio/gpio1/direction
 +
echo out > /sys/class/gpio/gpio2/direction
 +
echo 0 > /sys/class/gpio/gpio1/value
 +
echo 1 > /sys/class/gpio/gpio2/value </pre>
  
−
[[File:BTTest2021-09-09 132449.jpg|RTENOTITLE]]
+
<br/> '''RS-485 test&nbsp;'''
 +
<pre>Command&nbsp;: stty -F /dev/ttymxc1 115200
 +
          echo Serial Port Test > /dev/ttymxc1
 +
</pre>
  
−
=== '''&nbsp; 遠程訪問及文件傳輸(Remote Access and File Transimmion)''' ===
+
=== '''遠程訪問及文件傳輸(Remote Access and File Transimmion)''' ===
  
 
'''&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 查看主板IP位址&nbsp;(&nbsp;Chech IP Address )：'''​
 
'''&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 查看主板IP位址&nbsp;(&nbsp;Chech IP Address )：'''​
Line 297: Line 295:
 
SSH Remote Log into Device&nbsp;
 
SSH Remote Log into Device&nbsp;
  
−
*SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
+
*SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)  
−
*需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码
+
*需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码  
−
 
 
  
 +
&nbsp;
  
 
[[File:SSHsettingdetail.png|RTENOTITLE]]
 
[[File:SSHsettingdetail.png|RTENOTITLE]]
Line 306: Line 304:
 
[[File:SSHSetting2021-09-10 143631.jpg|RTENOTITLE]]
 
[[File:SSHSetting2021-09-10 143631.jpg|RTENOTITLE]]
  
−
 
+
&nbsp;
  
 
[[File:Sshsetting12021-09-10 143743n.jpg|RTENOTITLE]]
 
[[File:Sshsetting12021-09-10 143743n.jpg|RTENOTITLE]]
  
−
[[File:SSHLogin 2021-09-10 143913n.jpg|RTENOTITLE]]
+
[[File:RSB-3430 ssh connection.png|RTENOTITLE]]
  
 
== '''通用方法(General Method)''' ==
 
== '''通用方法(General Method)''' ==
  
−
=== &nbsp; '''&nbsp; &nbsp; 查看CPU温度(Check CPU Temperature)''' ===
+
=== '''查看CPU温度(Check CPU Temperature)''' ===
 
<pre>    root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600
 
<pre>    root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600
  
 
     # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°</pre>
 
     # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°</pre>
  
−
=== '''&nbsp; &nbsp; &nbsp;&nbsp;查看CPU频率(Check CPU Frequency)''' ===
+
=== '''查看CPU频率(Check CPU Frequency)''' ===
 
<pre>          cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq  
 
<pre>          cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq  
 
           >> 900000
 
           >> 900000
Line 325: Line 323:
 
           >> 1200000</pre>
 
           >> 1200000</pre>
  
−
=== '''&nbsp; &nbsp; &nbsp;&nbsp;查看内存容量(Check Memory&nbsp;Capacity)''' ===
+
=== '''查看内存容量(Check Memory&nbsp;Capacity)''' ===
 
<pre>root@imx8qxprom5620a1:/# busybox free -m
 
<pre>root@imx8qxprom5620a1:/# busybox free -m
 
             total      used      free    shared    buffers    cached
 
             total      used      free    shared    buffers    cached
Line 333: Line 331:
 
</pre>
 
</pre>
  
−
=== '''&nbsp; &nbsp; &nbsp;&nbsp;查看存储容量(Check Storage Capacity)''' ===
+
=== '''查看存储容量(Check Storage Capacity)''' ===
 
<pre>root@imx8qxprom5620a1:/# busybox df -h
 
<pre>root@imx8qxprom5620a1:/# busybox df -h
 
Filesystem                Size      Used Available Use% Mounted on
 
Filesystem                Size      Used Available Use% Mounted on
Line 349: Line 347:
 
root@imx8qxprom5620a1:/#</pre>
 
root@imx8qxprom5620a1:/#</pre>
  
−
=== '''&nbsp; &nbsp; &nbsp; 網路Ping測試(Ping Network Testing)''' ===
+
=== '''&nbsp;網路Ping測試(Ping Network Testing)''' ===
 
<pre>    ping 8.8.8.8
 
<pre>    ping 8.8.8.8
 
     PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
 
     PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
Line 355: Line 353:
 
     64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre>
 
     64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre>
  
−
=== '''&nbsp; &nbsp; &nbsp; 設置RTC (RTC Setting)&nbsp;''' ===
+
=== '''設置RTC (RTC Setting)&nbsp;''' ===
−
<pre>     root@imx8qxprom5620a1:/# systemctl stop ntpdate.service
+
<pre>RTC&nbsp;:&nbsp;
−
    root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date
+
$ date MMDDhhmm[[CC]YY][.ss]
−
            Wed Sep  8 16:07:00 UTC 2021
+
$ hwclock -w
−
            Wed Sep  8 16:07:00 UTC 2021
+
$ ntpdate tw.pool.ntp.org</pre>
−
    root@imx8qxprom5620a1:/# date
+
 
−
            Wed Sep  8 16:07:06 UTC 2021
+
=== '''Audio 測試''' ===
−
    root@imx8qxprom5620a1:/#'''</pre>
+
<pre>Line out&nbsp;:
 +
$ aplay -D plughw:0,0 Advantech.wav
 +
MIC in&nbsp;:  
 +
$ arecord -t wav -c 1 -r 44100 -d 10 test.wav
 +
</pre>
 +
 
 +
=== '''&nbsp;Display (LVDS:800x480)設置&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;''' ===
 +
<pre>U-boot command&nbsp;:  
 +
setenv mmcargs setenv bootargs console=${console},${baudrate} ${smp} root=${mmcroot} ${bootargs} video=mxcfb0:dev=ldb,800x480M@60,if=RGB24
 +
</pre>
 +
 
 +
== '''Linux&nbsp;BSP編譯方法(Linux&nbsp;BSP Compile Method)''' ==
 +
 
 +
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBVB_User_Guide '''Yocto 3.3'''] ===
  
−
'''&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;'''
+
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV9_User_Guide '''Yocto 2.5'''] ===
  
−
== '''Linux&nbsp;BSP編譯方法(Android BSP Compile Method)''' ==
+
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX6/Yocto_LBV8_User_Guide '''Yocto 2.1'''] ===
  
−
=== [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVA_User_Guide '''Yocto 3.0'''] ===
+
{| border="0" cellpadding="10" cellspacing="0" style="width:100%;"
 +
|-
 +
| <iframe height="230" key="advonline" level="campaign" path="en/aim-linux_community/" width="100%"></iframe>
 +
|}

Latest revision as of 08:59, 21 November 2023

產品介紹(Product introduction )

產品特性(Product Features)

  • NXP Arm® Cortex®-A53 i.MX8M Plus Quad/Dual up to 1.8 GHz
  • Onboard LPDDR4 4 GB / 6 GB, 4000MT/s memory
  • HDMI 1920x1080 at 60Hz, 1 Single or 1 Dual Channel 24 bit LVDS (or 1 4-Lane MIPI-DSI by BOM Option)
  • 1 4-wire RS-232/422/485, 1 USB3.2 Gen1 By 1, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
  • 1 mini-PCIe for 3G/4G, 1 M.2 2230 Key E Slot
  • Supports Yocto Linux and Android
  • Support I/O Expansions boards by UIO40-Express

 

產品官網連結(Product official website link) 

RSB-3430

硬件接口說明(Hardware interface introduction)

接口布局和尺寸(Layout and Sizes)

接口布局圖 Board Dimension Layout 

RTENOTITLE

 

RTENOTITLE

 机械尺寸  (Mechanical Characteristics)

RTENOTITLE

RTENOTITLE

 

 Connector List

RTENOTITLE

 

接口引脚定義 (Pin definitions)

RTC_BAT

DCIN

COM

HDMI

USB

M2

MiniPCIe

LVDS_BKLT_PWR

Backlight Voltage 

H4

CN1

CN2

LVDS

SD

SIM_Slot

快速入门 (Quick Start)

系统下载 (OS Download)

   

 Linux 燒錄方法 (Linux Flash eMMC Method)

1. 確認SD 在Ubuntu 電腦中的代號

RTENOTITLE

RTENOTITLE

2. 先將鏡像燒錄到SD Card 中( Create a bootable SD card ) 

'RTENOTITLE

 

 

RTENOTITLE

3.設定終端機(Set Debug Terminal) 

Debug 串口調試 (Debug port Setting)

以 Tera Term  为例介绍如何使用串口调试功能 

   Baud Rate波特率：115200
   Data 数据位：8
   Parity 奇偶校验：无
   Stop 停止位：1
   Flow Control流控：无
 

Tera Term Tool 

RTENOTITLE

RTENOTITLE

Check the Sriel port in Device Manager (查看PC端的串口号)：

if you can not identify the Serial device , please check your serial driver. 

RTENOTITLE

4. 將SD card 插入機器 

  RTENOTITLE

5. 檢查撥碼開關  ( 1 ON , 2 OFF) 

RTENOTITLE

6. 接上Debug Cable 

RTENOTITLE

7. 打開電源 

RTENOTITLE

8. 由終端機進入系統 

RTENOTITLE

9. 燒錄鏡像到 eMMC flash 

將3430A1AIM20LIV90146_DualQuad_flash_tool.tgz 複製到U盤中,插入機器的USB Port 

RTENOTITLE

在系統中 ,確認USB中燒錄資料 

RTENOTITLE

RTENOTITLE

在根目錄下 ,解壓縮 

RTENOTITLE

在mk_Inand 資料夾中執行 ./mksd-linux.sh 

RTENOTITLE

RTENOTITLE

RTENOTITLE

10. 移除SD 卡,從eMMC 開機. 

RTENOTITLE

 Linux系统的基本使用(Linux System Basic Operating Method)

載入預設值由uboot 設定(Load Default Setting in Uboot )

1. 開機時 在五秒內按下空白鍵 ,進入Uboot 

2. Command : 

    env default -a 

    saveenv 

    reset   

RTENOTITLE

顯示設定 (Display  Setting ) 

 預設值為: HDMI 輸出

RTENOTITLE

RTENOTITLE

乙太網路使用方法(Ethernent Testing Method)

Command : ifconfig 

RTENOTITLE

Command: Ping 8.8.8.8 

RTENOTITLE

 

WiFi & BT 使用方法(WIFI & Bluetooth Testing Method)

M.2 module (EWM-W162M201E) - WIFI / BT Function 
WIFI 

$ ifconfig mlan0 up
$ wpa_passphrase ${SSID} ${WPA_KEY} > /tmp/wpa.conf
$ wpa_supplicant -BDwext -imlan0 -c/tmp/wpa.conf
$ udhcpc -b -i mlan0

BlueTooth 

$ /usr/libexec/bluetooth/bluetoothd -C &
$ hciconfig hci0 up
$ bluetoothctl
$ discoverable on
$ pairable on
$ scan on
[NEW] FC:18:3C:8D:75:F4 Device ID 
$ scan off
$ pair FC:18:3C:8D:75:F4
$ connect FC:18:3C:8D:75:F4

 

3G使用方法(3G Testing Method)

Command:
3G (Telit HE910D) 
pppd connect 'chat -v -s -t 10 "" "AT" "" "ATDT*99#" "CONNECT" ""' user username password password /dev/ttyACM3 460800 nodetach crtscts debug usepeerdns defaultroute & 

USB 測試方式(USB Test metod )

USB 

Insert a USB disk

usb 1-1.2: new high-speed USB device number 4 using ci_hdrc
usb-storage 1-1.2:1.0: USB Mass Storage device detected
scsi2 : usb-storage 1-1.2:1.0
scsi 2:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sda] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] No Caching mode page found
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] No Caching mode page found
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 2:0:0:0: [sda] No Caching mode page found
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk

串口使用方法(Serial Port Operating Method)

RS-232 Test  

Command : stty -F /dev/ttymxc1 115200
          echo Serial Port Test > /dev/ttymxc1


RS-422 setting 

echo 134 > /sys/class/gpio/export
echo 135 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio1/direction
echo out > /sys/class/gpio/gpio2/direction
echo 1 > /sys/class/gpio/gpio1/value
echo 1 > /sys/class/gpio/gpio2/value

RS-422 test  

Command : stty -F /dev/ttymxc1 115200
          echo Serial Port Test > /dev/ttymxc1

RS-485 setting  

echo 134 > /sys/class/gpio/export
echo 135 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio1/direction
echo out > /sys/class/gpio/gpio2/direction
echo 0 > /sys/class/gpio/gpio1/value
echo 1 > /sys/class/gpio/gpio2/value


RS-485 test  

Command : stty -F /dev/ttymxc1 115200
          echo Serial Port Test > /dev/ttymxc1

遠程訪問及文件傳輸(Remote Access and File Transimmion)

              查看主板IP位址 ( Chech IP Address )：​ 

        Command : ifconfig

RTENOTITLE

Windows下SSH访问及文件传输

SSH Remote Log into Device 

  • SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
  • 需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码

 

RTENOTITLE

RTENOTITLE

 

RTENOTITLE

RTENOTITLE

通用方法(General Method)

查看CPU温度(Check CPU Temperature)

    root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600

    # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°

查看CPU频率(Check CPU Frequency)

           cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq 
           >> 900000
           cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq    
           >> 1200000

查看内存容量(Check Memory Capacity)

root@imx8qxprom5620a1:/# busybox free -m
             total       used       free     shared    buffers     cached
Mem:       1794920     516080    1278840      17252      9852        80292
-/+ buffers/cache:     425936    1368984
Swap:            0          0          0

查看存储容量(Check Storage Capacity)

root@imx8qxprom5620a1:/# busybox df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                13.4G      1.7G     11.1G  13% /
devtmpfs                395.8M      4.0K    395.8M   0% /dev
tmpfs                   876.4M         0    876.4M   0% /dev/shm
tmpfs                   876.4M     16.5M    859.9M   2% /run
tmpfs                   876.4M         0    876.4M   0% /sys/fs/cgroup
tmpfs                   876.4M      4.0K    876.4M   0% /tmp
tmpfs                   876.4M    280.0K    876.2M   0% /var/volatile
/dev/mmcblk0p2           13.6G      1.7G     11.3G  13% /run/media/mmcblk0p2
/dev/mmcblk0p1           63.9M     23.4M     40.5M  37% /run/media/mmcblk0p1
/dev/mmcblk1p1           63.9M     23.4M     40.5M  37% /run/media/mmcblk1p1
tmpfs                   175.3M     88.0K    175.2M   0% /run/user/0
root@imx8qxprom5620a1:/#

 網路Ping測試(Ping Network Testing)

     ping 8.8.8.8
     PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
     64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
     64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms

設置RTC (RTC Setting) 

RTC : 
$ date MMDDhhmm[[CC]YY][.ss]
$ hwclock -w
$ ntpdate tw.pool.ntp.org

Audio 測試

Line out : 
$ aplay -D plughw:0,0 Advantech.wav
MIC in : 
$ arecord -t wav -c 1 -r 44100 -d 10 test.wav

 Display (LVDS:800x480)設置         

U-boot command : 
setenv mmcargs setenv bootargs console=${console},${baudrate} ${smp} root=${mmcroot} ${bootargs} video=mxcfb0:dev=ldb,800x480M@60,if=RGB24

Linux BSP編譯方法(Linux BSP Compile Method)

Yocto 3.3

Yocto 2.5

Yocto 2.1

Retrieved from "https://ess-wiki.advantech.com.tw/wiki/index.php?title=RSB-3430_user_guide&oldid=32309"