Difference between revisions of "ROM-2620 user guide"
Jems.cheng (talk | contribs) (→產品特性(Features)) |
|||
(160 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | + | | |
= 產品介紹 = | = 產品介紹 = | ||
− | |||
− | |||
== '''產品特性(Features)''' == | == '''產品特性(Features)''' == | ||
Line 13: | Line 11: | ||
*1 x 4 lane MIPI-DSI 1 x USB2.0, 1 x USB 2.0 OTG, 5 x UART, 2 x I2C, 24 x GPIO, 6 x PWM, 1 x CAN | *1 x 4 lane MIPI-DSI 1 x USB2.0, 1 x USB 2.0 OTG, 5 x UART, 2 x I2C, 24 x GPIO, 6 x PWM, 1 x CAN | ||
*Ultra small size form factor - OSM | *Ultra small size form factor - OSM | ||
− | *Support Ycoto Linux and Microsoft Azure Sphere OS | + | *Support Ycoto Linux and Microsoft Azure Sphere OS |
+ | |||
+ | | ||
== '''產品官網連結(Product information Link)''' == | == '''產品官網連結(Product information Link)''' == | ||
− | [https://www.advantech.com/zh-tw/products/ | + | [https://www.advantech.com/zh-tw/products/8fc6f753-ca1d-49f9-8676-10d53129570f/rom-2620/mod_294031c8-4a21-4b95-adf2-923c412ef761 '''ROM-2620'''] |
= '''接口布局和尺寸(Layout and Sizes)''' = | = '''接口布局和尺寸(Layout and Sizes)''' = | ||
− | === '''ROM- | + | === '''ROM-2620 接口布局圖 Board Dimension Layout ''' === |
− | [[File:ROM- | + | [[File:ROM-2620 1.jpg|480px|ROM-2620 1.jpg]][[File:ROM-2620 2.jpg|480px|ROM-2620 2.jpg]] |
| | ||
− | === ''' | + | === '''ROM-ED91 接口布局圖 Board Dimension Layout''' === |
− | [[File: | + | '''[[File:ROM-2620 ED91 IO.png|RTENOTITLE]]''' |
| | ||
− | |||
− | |||
=== '''主板内置插针式引脚排序方式 (Pin Header defination) ''' === | === '''主板内置插针式引脚排序方式 (Pin Header defination) ''' === | ||
− | === '''Internal I/O''' === | + | === '''Internal I/O, Jummper/Switch List:''' === |
− | |||
− | |||
− | |||
− | |||
{| border="1" cellpadding="1" cellspacing="1" style="width: 763px;" | {| border="1" cellpadding="1" cellspacing="1" style="width: 763px;" | ||
Line 50: | Line 44: | ||
| style="width: 301px;" | '''Function''' | | style="width: 301px;" | '''Function''' | ||
|- | |- | ||
− | | | + | | DCIN1401 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | 12V DCIN connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1301 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | BT0_CFG1/4, BT1_CFG6/7/9/11 |
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | COMB |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | RS232/422/485 |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1302 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | BT0_CFG0, BT1_CFG4/5, BOOT_SEL0#/1#, MOD_ON |
|- | |- | ||
− | | | + | | COMA |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | RS232/422/485 |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1203 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | UARTB_MODE0, UART_MODE1 |
|- | |- | ||
− | | | + | | LAN |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | LAN Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1204 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | UARTB_TERM, UARTB_SLEW |
|- | |- | ||
− | | | + | | USB1 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | USB2.0 port Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1206 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | U1205_RX_TERM, U1205_MODE2 |
|- | |- | ||
− | | | + | | USB0_OTG1 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | Micro USB Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1201 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | UARTA_MODE0, UART_MODE1 |
|- | |- | ||
− | | | + | | AJ |
| style="width: 296.422px;" | Line Out Connector | | style="width: 296.422px;" | Line Out Connector | ||
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1202 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | UARTA_TERM, UARTA_SLEW |
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
− | | | + | | MIC |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | MIC Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1205 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | U1202_RX_TERM, U1202_MODE2 |
|- | |- | ||
− | | | + | | CAN |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | CAN Bus Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1303 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | Power button |
|- | |- | ||
− | | | + | | COME_DEBUG |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | M-core debug console |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SW1304 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | Reset button |
|- | |- | ||
− | | | + | | COMC |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | COM |
− | | style="width: 64px;" | | + | | style="width: 64px;" | I2S_CN |
− | | style="width: 301px;" | | + | | style="width: 301px;" | I2S Connector |
|- | |- | ||
− | | | + | | COMD |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | A-core debug console |
− | | style="width: 64px;" | | + | | style="width: 64px;" | CN501 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | CAN0_H, CAN0_L terminatl resistors |
|- | |- | ||
− | | | + | | I2C1101 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | I2C Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SD_SLT |
− | | style="width: 301px;" | | + | | style="width: 301px;" | SD select |
|- | |- | ||
− | | | + | | I2C1102 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | I2C Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | GPIO1101 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | GPIO header |
|- | |- | ||
− | | | + | | CN601 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | M.2 Key E Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | SPI_CN1101 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | PWM header |
|- | |- | ||
− | | | + | | CN701 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | MIPI-CSI Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | CN1101 |
− | | style="width: 301px;" | | + | | style="width: 301px;" | SPI header |
|- | |- | ||
− | | | + | | LVDS |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | LVDS Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | LVDS_VDD_SLT |
− | | style="width: 301px;" | | + | | style="width: 301px;" | LVDS power select select header |
|- | |- | ||
− | | | + | | LVDS_BKLT_PWR |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | LVDS Backlight Connector |
− | | style="width: 64px;" | | + | | style="width: 64px;" | LVDS_BKLT_SLT |
− | | style="width: 301px;" | | + | | style="width: 301px;" | LVDS Backlight power select header |
|- | |- | ||
− | | | + | | BAT1 |
− | | style="width: 296.422px;" | | + | | style="width: 296.422px;" | Battery Connector |
− | |||
− | |||
− | |||
− | |||
− | |||
| style="width: 64px;" | | | style="width: 64px;" | | ||
| style="width: 301px;" | | | style="width: 301px;" | | ||
Line 164: | Line 143: | ||
=== '''Rear I/O ''' === | === '''Rear I/O ''' === | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
=== '''LED Function List ''' === | === '''LED Function List ''' === | ||
Line 298: | Line 151: | ||
| Function | | Function | ||
|- | |- | ||
− | | | + | | PD1405 |
− | | | + | | +V5_MOD |
|- | |- | ||
− | | | + | | PD1502 |
− | | | + | | +V3.3 |
|- | |- | ||
− | | | + | | PD1503 |
− | | | + | | +V5 |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|} | |} | ||
+ | |||
+ | | ||
=== '''Switch Settings''' === | === '''Switch Settings''' === | ||
− | *[[ | + | *[http://ess-wiki.advantech.com.tw/view/ROM-2620_SW1301.png SW1301(BT0_CFG1/4, BT1_CFG6/7/9/11)] |
− | *[[ | + | *[http://ess-wiki.advantech.com.tw/view/ROM-2620_SW1302.png SW1302(BT0_CFG0, BT1_CFG4/5, BOOT_SEL0#/1#, MOD_ON)] |
− | *[[ | + | *[http://ess-wiki.advantech.com.tw/view/SW1203_(UARTB_MODE0,_UART_MODE1) SW1203 (UARTB_MODE0, UART_MODE1)] |
− | *[[ | + | *[http://ess-wiki.advantech.com.tw/view/SW1204_(UARTB_TERM,_UARTB_SLEW) SW1204 (UARTB_TERM,_UARTB_SLEW)] |
− | *[[ | + | *[[SW1206_(U1205_RX_TERM,_U1205_MODE2)|SW1206_(U1205_RX_TERM,_U1205_MODE2)]] |
− | *[[ | + | *[[SW1201_(UARTA_MODE0,_UART_MODE1|SW1201 (UARTA_MODE0, UART_MODE1]]) |
− | *[[ | + | *[[SW1202_(UARTA_TERM,_UARTA_SLEW)|SW1202 (UARTA_TERM,_UARTA_SLEW)]] |
+ | *[http://ess-wiki.advantech.com.tw/view/SW1205_(U1202_RX_TERM,_U1202_MODE2) SW1205_(U1202_RX_TERM,_U1202_MODE2)] | ||
+ | *[http://ess-wiki.advantech.com.tw/view/SW1303_(Power_button) SW1303_(Power_button)] | ||
+ | *[http://ess-wiki.advantech.com.tw/view/SW1304_(Reset_button) SW1304_(Reset_button)] | ||
+ | *[http://ess-wiki.advantech.com.tw/view/SD_SLT_(SD_select) SD_SLT_(SD_select)] | ||
+ | *[[LVDS_VDD_SLT_(LVDS_power_select_select_header)|LVDS_VDD_SLT_(LVDS_power_select_select_header)]] | ||
+ | *[[LVDS_BKLT_SLT_(LVDS_Backlight_power_select_header)|LVDS_BKLT_SLT_(LVDS_Backlight_power_select_header)]] | ||
+ | |||
+ | | ||
=== '''接口引脚定義 (Connector Pin definitions)''' === | === '''接口引脚定義 (Connector Pin definitions)''' === | ||
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_DCIN.png DCIN1401] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_COMB.png COMB] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_COMA.png COMA] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_LAN.png LAN] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_USB1.png USB1] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_USB0_OTG1.png USB0_OTG1] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_AJ.png AJ(Audio_Jack)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_MIC.png MIC] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_CAN.png CAN] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_COME_DEBUG.png COME_DEBUG(M-core_debug)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_COMC.png COMC] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_COMD.png COMD(A-code_debug)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_I2C1101.png I2C1101] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_I2C1102.png I2C1102] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_CN601.png CN601(M.2_Key_E)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_CN701.png CN701(MIPI-CSI)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_LVDS.png LVDS] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_LVDS_BKLT_PWR.png LVDS_BKLT_PWR] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_BAT1.png BAT1] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_I2S_CN.png I2S_CN(I2S)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_CN501.png CN501(CAN0_H/CAN0_L)] |
− | *[ | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_GPIO1101.png GPIO1101] |
− | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_SPI_CN1101.png SPI_CN1101(PWM)] | |
− | + | *[http://ess-wiki.advantech.com.tw/view/File:ROM-2620_CN1101.png CN1101(SPI)] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | *[ | ||
− | |||
− | |||
− | |||
− | *[ | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
=== '''机械尺寸 ('''Mechanical Characteristics) === | === '''机械尺寸 ('''Mechanical Characteristics) === | ||
− | '''ROM- | + | '''ROM-2620''' |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | [[File:ROM-2620 Module Dimension.png|RTENOTITLE]] | |
---- | ---- | ||
− | |||
= '''快速入门 (Quick Start)''' = | = '''快速入门 (Quick Start)''' = | ||
Line 434: | Line 222: | ||
*'''Linux系统 (Linux OS)'''''' ''' | *'''Linux系统 (Linux OS)'''''' ''' | ||
− | '''Yocto | + | '''Yocto 4.0: '''[http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/OS_Support_List_4.0_release_ROM-2620 IoTGateway/BSP/Linux/iMX8/OS Support List 4.0 release ROM-2620 - ESS-WIKI (advantech.com.tw)] |
− | ---- | + | '''Yocto 4.2: '''[http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/OS_Support_List_4.2_release_ROM-2620 IoTGateway/BSP/Linux/iMX8/OS Support List 4.2 release ROM-2620 - ESS-WIKI (advantech.com.tw)]''' ''' |
+ | | ||
+ | |||
+ | | ||
=== '''Linux 燒錄方法 (Linux Flash eMMC Method)''' === | === '''Linux 燒錄方法 (Linux Flash eMMC Method)''' === | ||
Line 445: | Line 236: | ||
Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system) | Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system) | ||
− | [[File: | + | [[File:ROM-2620 USBDeviceID.png|RTENOTITLE]] |
Step1: 創造一張可開機的SD 卡 (Create a bootable SD card) | Step1: 創造一張可開機的SD 卡 (Create a bootable SD card) | ||
Line 451: | Line 242: | ||
<span style="font-size:small;">Command :</span> | <span style="font-size:small;">Command :</span> | ||
− | <span style="font-size:small;">'''sudo dd if= | + | <span style="font-size:small;">'''~$ sudo dd if=2620A1AIM34LIVC0054_iMX8ULP_1G_flash_tool/image/imx-image-full-imx8ulprom2620a1-20230627062759.rootfs.wic of=/dev/sde bs=1M conv=fsync status=progress'''</span> |
− | [[File: | + | [[File:ROM-2620 dd img to sd.png|RTENOTITLE]] |
Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot) | Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot) | ||
− | + | Step3: 確認開機選擇指撥開關 | |
− | + | [[File:ROM-2620 Boot Switch.png|RTENOTITLE]] | |
− | + | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" | |
+ | |- | ||
+ | | EMMC boot: | ||
+ | | SW1301: 1_2_5_6 ON<br/> SW1302: 4_6 ON | ||
+ | |- | ||
+ | | SD boot: | ||
+ | | SW1301: 1_2_3_4 ON<br/> SW1302: 4_6 ON | ||
+ | |- | ||
+ | | Serial download: | ||
+ | | SW1301: All OFF<br/> SW1302: 5_6 ON | ||
+ | |} | ||
− | & | + | Step4:打開電源 和 終端機 (Turn on the Power & Terminal) |
− | + | [[File:ROM-2620 User login.png|RTENOTITLE]] | |
− | + | Step5: 複製flash tool到U盤中, 解壓縮flash tools檔案,(copy to USB Disk, then unzip the flash tools file)(Test with 32G SD card) | |
− | + | 複製檔案到U盤中 (Copy the flash file to USB Disk), 解壓縮flash tool到home目錄(Unzip the file to home) | |
− | + | #tar zxvf /run/media/New\ Volume-sda/2620A1AIM34LIVC0054_iMX8ULP_1G_flash_tool.tgz -C ~ | |
− | + | [[File:ROM-2620 tar img.png|RTENOTITLE]] | |
− | | + | 5. 進入flsah tool下的mk_inand資歷夾, 執行指令./mksd-linux.sh /dev/mmcblk0燒錄image到eMMC(Connect USB Disk to ROM-2620 system, extract the flash tool and browser to mk_inand folder and execute flash shell script "./mksd-linux.sh /dev/mmcblk0" |
− | + | 解壓縮後如果沒有mksd-linux.sh檔案, 可以到以下連結下載並複製到mk_inand資料夾下(If there is no mksd-linux.sh file in mk_inand directory. Please download from the link below and place it in mk_inand directory: | |
− | + | [https://github.com/ADVANTECH-Corp/RISC_tools_scripts/blob/kirkstone/imx8/mksd-linux.sh mksd-linux.sh] | |
− | + | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | {| border="1" cellpadding="1" cellspacing="1" style="width:500px;" | ||
|- | |- | ||
− | | ROM- | + | | ROM-2620 |
− | | | + | | Device node |
|- | |- | ||
| SD card | | SD card | ||
− | | /dev/ | + | | /dev/mmcblk2 |
|- | |- | ||
| eMMC | | eMMC | ||
− | | /dev/ | + | | /dev/mmcblk0 |
|} | |} | ||
− | [[File: | + | [[File:ROM-2620 Flash eMMC.png|RTENOTITLE]] |
− | 6. | + | 6. 切換開機switch來設定成從eMMC開機(Change boot switch to boot from eMMC. Reboot system). |
| | ||
Line 523: | Line 308: | ||
Stop 停止位:1 | Stop 停止位:1 | ||
Flow Control流控:无</pre> | Flow Control流控:无</pre> | ||
− | |||
− | |||
Tera Term Tool | Tera Term Tool | ||
Line 540: | Line 323: | ||
Debug port connection (串口連接) | Debug port connection (串口連接) | ||
− | [[File: | + | Log into Terminal Tool (进入串口调试终端): |
+ | |||
+ | [[File:ROM-2620 User login.png|RTENOTITLE]] | ||
| | ||
− | + | = '''Linux系统的基本使用(Linux System Basic Operating Method)''' = | |
+ | |||
+ | === '''UUU 使用方法(USB Connection (OTG port))''' === | ||
+ | |||
+ | '''Connect USB cable to USB OTG port.''' | ||
+ | |||
+ | '''Change boot switch to "SW1301 all OFF, SW1302: 5_6:on" to boot from force recovery mode.''' | ||
+ | |||
+ | | ||
− | + | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" | |
+ | |- | ||
+ | | Serial download: | ||
+ | | SW1301: All OFF<br/> SW1302: 5_6 ON | ||
+ | |} | ||
+ | '''[[File:ROM-2620 uuu device id.png|RTENOTITLE]]''' | ||
− | + | Download uuu tool from link below: | |
− | = | + | [https://github.com/nxp-imx/mfgtools/releases?page=3 Releases · nxp-imx/mfgtools (github.com)] |
− | + | The uuu verison we tested is 1.4.193: [https://github.com/nxp-imx/mfgtools/releases/download/uuu_1.4.193/uuu uuu] | |
− | uuu (Universal Update Utility) for nxp imx chips -- | + | uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.193-0-ge56424c |
− | + | Perpare uboot and image files below: | |
− | + | 2620A1AIM34LIVC0064_iMX8ULP_1G_imx-boot.tgz<br/> 2620A1AIM34LIVC0064_iMX8ULP_1G_flash_tool.tgz | |
− | + | 1. Download uuu | |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">$ wget [https://github.com/nxp-imx/mfgtools/releases/download/uuu_1.4.193/uuu https://github.com/nxp-imx/mfgtools/releases/download/uuu_1.4.193/uuu]<br/> $ chmod a+x uuu<br/> $ tar zxvf 2620A1AIM34LIVC0064_iMX8ULP_1G_imx-boot.tgz<br/> $ tar zxvf 2620A1AIM34LIVC0064_iMX8ULP_1G_flash_tool.tgz</div> | ||
+ | Type command below to flash eMMC: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">$ sudo ./uuu -b emmc_all 2620A1AIM34LIVC0064_iMX8ULP_1G_imx-boot/imx-boot-imx8ulprom2620a1-1G.bin-flash_singleboot_m33 2620A1AIM34LIVC0064_iMX8ULP_1G_flash_tool/image/imx-image-full-imx8ulprom2620a1-20230901105531.rootfs.wic</div> | ||
+ | [[File:ROM-2620 uuu flash.png|RTENOTITLE]] | ||
− | + | | |
− | + | | |
− | + | | |
− | === '''Display Setting (ROM- | + | === '''Display Setting (ROM-2620)''' === |
− | ''' U-boot Command :''' | + | ''' U-boot Command :''' |
*Display | *Display | ||
− | + | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">=> setenv fdtfile imx8ulp-rom2620-a1-lt9211.dtb<br/> => saveenv<br/> => boot</div> | |
− | + | [[File:ROM-2620 2CH LVDS uboot.png|RTENOTITLE]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | === ''' | + | |
+ | |||
+ | | ||
+ | |||
+ | === '''Audio(Audio Testing Methid)''' === | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># cat /proc/asound/cards</div> | ||
+ | 0 [sgtl5000 ]: sgtl5000 - sgtl5000 <br/> sgtl5000 | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># amixer set Mic 50%<br/> # amixer set Lineout 100%<br/> # amixer set PCM 100%</div> | ||
+ | '''Record and playback:''' | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">'''# arecord -t wav -c 2 -r 44100 -d 10 /tmp/mic.wav'''</div> <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">'''# aplay /tmp/mic.wav'''</div> | ||
+ | | ||
+ | |||
+ | === '''M.2 WiFi/BT測試方法(M.2 WiFi/BT Testing Method)''' === | ||
+ | |||
+ | *Test Wi-Fi with EWM-W167 on C0048 version: Change SD_SLT to 2-3 | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">=> setenv fdtfile imx8ulp-rom2620-a1-m2-sdio.dtb<br/> => saveenv<br/> => boot</div> | ||
+ | In Linux user space: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># iwconfig<br/> # ifconfig wlan0 up<br/> # iwlist wlan0 scan | grep ESSID<br/> # killall wpa_supplicant<br/> # ifconfig wlan0 up<br/> # wpa_passphrase "Pilimao" "0913079939" > /tmp/wpa.conf<br/> # wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf<br/> # udhcpc -b -i wlan0<br/> # ping 8.8.8.8</div> | ||
+ | Add name server: nameserver 8.8.8.8 in resolv.conf file | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># vi /etc/resolv.conf<br/> # ping google.com</div> | ||
+ | Test BT: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># cd /opt/rtl8723bs_bt/<br/> # ./start_bt.sh ttyLP0<br/> # hciconfig hci0 up<br/> # hciconfig<br/> # bluetoothctl<br/> # discoverable on<br/> # pairable on<br/> # scan on<br/> # info 84:C5:A6:D3:AF:E4<br/> # pair 84:C5:A6:D3:AF:E4<br/> # connect 84:C5:A6:D3:AF:E4<br/> # paired-devices<br/> # disconnect 84:C5:A6:D3:AF:E4<br/> # remove 84:C5:A6:D3:AF:E4</div> | ||
+ | *Test Wi-Fi with EWM-W194M201E Module (SDIO Interface) | ||
+ | |||
+ | Step 1: Press enter after boot. The system will stop at u-boot, and change dtb file by below command. | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">=> setenv fdtfile imx8ulp-rom2620-a1-m2-sdio-88w8997.dtb<br/> => saveenv<br/> => boot</div> | ||
+ | Step 2: Install driver by below command. | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># rmmod mwifiex_sdio mwifiex<br/> # modprobe moal mod_para=nxp/wifi_mod_para.conf<br/> # modprobe btnxpuart</div> | ||
+ | Step 3: WIFI test command. | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># ifconfig mlan0 up<br/> # wpa_passphrase ASUS-917C qwert12345 > /tmp/wpa.conf<br/> # wpa_supplicant -d -B -i mlan0 -c /tmp/wpa.conf<br/> # udhcpc -i mlan0</div> | ||
+ | *Test Bluetooth with EWM-W194M201E Module (UART Interface) | ||
+ | |||
+ | Step 1: Please refer to above step 1.<br/> Step 2: Please refer to above step 2. | ||
+ | |||
+ | Step 3: Bluetooth test command. | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># hciconfig hci0 up<br/> # bluetoothctl<br/> # discoverable on<br/> # pairable on<br/> # scan on<br/> [NEW] FC:18:3C:8D:75:F4 myphone<br/> # scan off<br/> # pair FC:18:3C:8D:75:F4<br/> # connect FC:18:3C:8D:75:F4</div> | ||
+ | | ||
+ | |||
+ | | ||
+ | |||
+ | === '''Serial Port測試方法(Serial Testing Method)(COM A/C)''' === | ||
+ | |||
+ | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" | ||
+ | |- | ||
+ | | COMA | ||
+ | | /dev/ttyLP0 | ||
+ | |- | ||
+ | | COMB(M33 Domain) | ||
+ | | | ||
+ | |- | ||
+ | | COMC | ||
+ | | /dev/ttyLP2 | ||
+ | |- | ||
+ | | COMD | ||
+ | | /dev/ttyLP1 | ||
+ | |- | ||
+ | | COME_DEBUG | ||
+ | | M33 debug port | ||
+ | |} | ||
+ | |||
+ | *'''RS-232 Loopback Test (eg. COMA: ttyLP0):''' | ||
+ | |||
+ | Step 1: First change ROM-ED91 SW1201 to ‘01’.<br/> Step 2: Run test command. | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># stty -F /dev/ttyLP0 speed 115200 -echo<br/> # cat /dev/ttyLP0 &<br/> # echo test > /dev/ttyLP0</div> | ||
+ | *'''RS-422 Test:''' | ||
− | + | Step 1: First change ROM-ED91 SW1201 to ‘11’.<br/> Step 2: Test RS-422 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following: | |
− | + | Adam-4520 RX- <-->ROM-2620 COMA DB9 Pin 1,<br/> Adam-4520 RX+ <-->ROM-2620 COMA DB9 Pin 2,<br/> Adam-4520 TX- <-->ROM-2620 COMA DB9 Pin 4,<br/> Adam-4520 TX+ <--> ROM-2620 COMA DB9 Pin 3 | |
− | ''' | + | Step 3: Run below command: |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># stty -F /dev/ttyLP0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke<br/> # cat /dev/ttyLP0 &<br/> # echo "Serial Test" > /dev/ttyLP0</div> | ||
+ | *'''RS-485 Test:''' | ||
− | + | Step 1: First change ROM-ED91 SW1201 to ‘10’.<br/> Step 2: Test RS-485 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following: | |
− | + | Adam-4520 Data- <-->ROM-2620 COMA DB9 Pin 1,<br/> Adam-4520 Data+ <-->ROM-2620 COMA DB9 Pin 2 | |
− | < | ||
− | </ | + | Step 3: Run below command: |
− | < | + | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># stty -F /dev/ttyLP0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke<br/> # cat /dev/ttyLP0 &<br/> # echo "Serial Test" > /dev/ttyLP0</div> |
− | + | | |
− | |||
− | |||
− | |||
− | |||
− | + | | |
− | |||
− | |||
− | |||
− | |||
− | + | | |
− | |||
− | |||
− | |||
− | + | === '''I2C測試方法(I2C Testing Method)''' === | |
− | + | Step 1: Plug in ROM-EG70<br/> Step 2: Test by below command (eg. I2C-6 I2C_1101): | |
− | < | + | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># modprobe at24<br/> # echo -n $'\x06\x05\x04\x03\x02\x01' > test<br/> # dd if=test of=/sys/bus/i2c/devices/6-0050/eeprom<br/> # hexdump -C /sys/bus/i2c/devices/6-0050/eeprom -n 64</div> |
− | Test | + | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | </ | ||
− | + | | |
− | + | === '''USB測試方法(USB Testing Method)''' === | |
− | === | + | USB disk test (USB 2.0)<br/> Step 1: Issue the following command (lsusb -t) after inserting a USB disk into the USB 2.0 port to check if the USB device is listed. Step 2: Test (eg. if usb disk is /dev/sda) |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># dd if=/dev/urandom of=data bs=1 count=1024<br/> # dd if=/dev/sda of=backup bs=1 count=1024 skip=4096 # dd if=data of=/dev/sda bs=1 seek=4096<br/> # dd if=/dev/sda of=data1 bs=1 count=1024 skip=4096 # diff data data1<br/> # dd if=backup of=/dev/sda bs=1 seek=4096</div> | ||
+ | | ||
− | + | | |
− | + | === '''RTC測試方法(RTC Testing Method)''' === | |
+ | Step 1: Set system time to current, then write to RTC | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># date 021010452023 && hwclock -w && date</div> | ||
+ | Step 2: Set one incorrect time, then read time from RTC to verify | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># date 010100002000 && hwclock -r && date</div> | ||
| | ||
− | |||
− | + | === '''eMMC/SD測使方法(eMMC/SD Testing Method)''' === | |
− | + | ||
+ | '''Device Routes'''<br/> eMMC: /dev/mmcblk0 <br/> SD: /dev/mmcblk2 | ||
− | + | '''Test (eg. emmc)''' | |
− | |||
− | Step | + | '''Step 1: Test command:''' |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;">'''# dd if=/dev/urandom of=data bs=1 count=1024<br/> # dd if=/dev/mmcblk0 of=backup bs=1 count=1024 skip=4096<br/> # dd if=data of=/dev/mmcblk0 bs=1 seek=4096<br/> # dd if=/dev/mmcblk0 of=data1 bs=1 count=1024 skip=4096<br/> # diff data data1<br/> # dd if=backup of=/dev/mmcblk0 bs=1 seek=4096'''</div> | ||
+ | | ||
− | + | === '''乙太網路使用方法(Ethernent Testing Method)''' === | |
− | |||
− | + | '''Command : ifconfig ''' | |
− | + | [[File:ROM-2620 ifconfig.png|RTENOTITLE]] | |
− | |||
− | |||
− | |||
− | |||
− | + | '''Command: Ping - I eth1 8.8.8.8 or Ping - I eth0 8.8.8.8 ''' | |
− | + | [[File:ROM-2620 ping.png|RTENOTITLE]] | |
− | + | | |
− | + | | |
− | + | === '''GPIO使用方法(GPIO Operating Method)''' === | |
− | + | '''GPIO pin:''' | |
− | + | {| border="1" cellpadding="1" cellspacing="1" style="width: 500px;" | |
+ | |- | ||
+ | | GPIO1101 pin | ||
+ | | Pin Name | ||
+ | | CPU Ball Name | ||
+ | | GPIO number | ||
+ | |- | ||
+ | | 1 | ||
+ | | GPIO_A_0 | ||
+ | | PTC0 | ||
+ | | 416 | ||
+ | |- | ||
+ | | 2 | ||
+ | | GPIO_A_1 | ||
+ | | PTC1 | ||
+ | | 417 | ||
+ | |- | ||
+ | | 3 | ||
+ | | GPIO_A_2 | ||
+ | | PTC2 | ||
+ | | 418 | ||
+ | |- | ||
+ | | 4 | ||
+ | | GPIO_A_3 | ||
+ | | PTC3 | ||
+ | | 419 | ||
+ | |- | ||
+ | | 5 | ||
+ | | GPIO_A_4 | ||
+ | | PTC4 | ||
+ | | 420 | ||
+ | |- | ||
+ | | 6 | ||
+ | | GPIO_A_5 | ||
+ | | PTC12 | ||
+ | | 428 | ||
+ | |- | ||
+ | | 7 | ||
+ | | GPIO_B_0 | ||
+ | | PTC18 | ||
+ | | 434 | ||
+ | |- | ||
+ | | 8 | ||
+ | | GPIO_B_1 | ||
+ | | PTC19 | ||
+ | | 435 | ||
+ | |- | ||
+ | | 9 | ||
+ | | GPIO_B_2 | ||
+ | | PTC20 | ||
+ | | 436 | ||
+ | |- | ||
+ | | 10 | ||
+ | | GPIO_B_3 | ||
+ | | PTC21 | ||
+ | | 437(Use for M2_SDIO_RST) | ||
+ | |- | ||
+ | | 11 | ||
+ | | GPIO_B_4 | ||
+ | | PTC22 | ||
+ | | 438(Use for M2_W_DISABLE2) | ||
+ | |- | ||
+ | | 12 | ||
+ | | GPIO_B_5 | ||
+ | | PTC23 | ||
+ | | 439(Use for M2_W_DISABLE1) | ||
+ | |- | ||
+ | | 13 | ||
+ | | GPIO_B_6 | ||
+ | | PTB0 | ||
+ | | 448 | ||
+ | |- | ||
+ | | 14 | ||
+ | | GPIO_B_7 | ||
+ | | PTB1 | ||
+ | | 449 | ||
+ | |- | ||
+ | | 15 | ||
+ | | GPIO_C_0 | ||
+ | | PTD12 | ||
+ | | 140 | ||
+ | |- | ||
+ | | 16 | ||
+ | | GPIO_C_1 | ||
+ | | PTD13 | ||
+ | | 141 | ||
+ | |- | ||
+ | | 17 | ||
+ | | GPIO_C_2 | ||
+ | | PTF1 | ||
+ | | 193 | ||
+ | |- | ||
+ | | 18 | ||
+ | | GPIO_C_3 | ||
+ | | PTF7 | ||
+ | | 199(Use for LVDS_Bridge_RST) | ||
+ | |- | ||
+ | | 19 | ||
+ | | PTB6 | ||
+ | | PTB6 | ||
+ | | 454 | ||
+ | |- | ||
+ | | 20 | ||
+ | | PTA5 | ||
+ | | PTA5 | ||
+ | | 485 | ||
+ | |} | ||
− | + | GPIO Loopback Test (Using GPIO1 and GPIO2 as examples) | |
− | + | Step 1: Connect GPIO1 and GPIO2 | |
− | + | Step 2: Export GPIO interface | |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 416 > /sys/class/gpio/export<br/> # echo 417 > /sys/class/gpio/export</div> | ||
+ | Step 3: Set GPIO direction | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo out > /sys/class/gpio/gpio1/direction<br/> # echo in > /sys/class/gpio/gpio2/direction</div> | ||
+ | Step 4: Read value and set output value than check | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># cat /sys/class/gpio/gpio2/value 0<br/> # echo 1 > /sys/class/gpio/gpio1/value<br/> # cat /sys/class/gpio/gpio2/value<br/> 1</div> | ||
+ | === '''Camera使用方法(Camera Testing Method)''' === | ||
− | + | MIPI-CSI0 (Tested with OV5640 + mini-SAS to MIPI-CSI Cable): OV5640 CSI (CN701): Connect OV5640 camera to EG-55 CAM3 | |
− | === | + | Step 1: Take pictures |
− | < | + | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># gst-launch-1.0 v4l2src num-buffers=1 device=/dev/video0 ! video/x-raw,width=640,height=480 ! jpegenc ! filesink location=sample.jpeg</div> |
+ | Step 2: View on panel | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># gplay-1.0 sample.jpeg</div> | ||
+ | | ||
− | + | === '''PWM測試方法(PWM Testing Method)''' === | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | Please use oscilloscope to check waveform. | |
− | === | + | PWM1: |
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 4 > /sys/class/pwm/pwmchip0/export<br/> # echo 1000000 > /sys/class/pwm/pwmchip0/pwm4/period<br/> # echo 500000 > /sys/class/pwm/pwmchip0/pwm4/duty_cycle<br/> # echo 1 > /sys/class/pwm/pwmchip0/pwm4/enable</div> | ||
+ | PWM2: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 5 > /sys/class/pwm/pwmchip6/export<br/> # echo 1000000 > /sys/class/pwm/pwmchip6/pwm5/period<br/> # echo 500000 > /sys/class/pwm/pwmchip6/pwm5/duty_cycle<br/> # echo 1 > /sys/class/pwm/pwmchip6/pwm5/enable</div> | ||
+ | PWM3: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 2 > /sys/class/pwm/pwmchip6/export<br/> # echo 1000000 > /sys/class/pwm/pwmchip6/pwm2/period<br/> # echo 500000 > /sys/class/pwm/pwmchip6/pwm2/duty_cycle<br/> # echo 1 > /sys/class/pwm/pwmchip6/pwm2/enable</div> | ||
+ | PWM4: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 3 > /sys/class/pwm/pwmchip6/export<br/> # echo 1000000 > /sys/class/pwm/pwmchip6/pwm3/period<br/> # echo 500000 > /sys/class/pwm/pwmchip6/pwm3/duty_cycle<br/> # echo 1 > /sys/class/pwm/pwmchip6/pwm3/enable</div> | ||
+ | PWM5: | ||
+ | <div style="background:#eeeeee;border:1px solid #cccccc;padding:5px 10px;"># echo 4 > /sys/class/pwm/pwmchip6/export<br/> # echo 1000000 > /sys/class/pwm/pwmchip6/pwm4/period<br/> # echo 500000 > /sys/class/pwm/pwmchip6/pwm4/duty_cycle<br/> # echo 1 > /sys/class/pwm/pwmchip6/pwm4/enable</div> | ||
+ | | ||
− | ''' | + | === '''M33 Function''' === |
− | |||
− | + | We use default M-core firmware to verify each of IO feature. User should connect COME_DEBUG port to PC and there were show screen as demonstration below: | |
− | + | [[File:ROM-2620 M33.png|RTENOTITLE]] | |
− | + | Press C for test mode of CAN bus<br/> Press Q for test mode of QSPI<br/> Press M for test mode of LPSPI master<br/> Press S for test mode of LPSPI slave<br/> Press U for test mode of LPUART<br/> About this firmware, user should note that if you want to switch to another test mode, you must reboot the system. | |
− | + | | |
− | |||
| | ||
− | + | ==== '''CAN Bus''' ==== | |
− | [[File: | + | '''Step 1: Prepare two pcs rom-2620. One for ‘Node A’ one for ‘Node B’<br/> Step 2: Connect these two boards (HI-HI/LO-LO)<br/> Step 3: The test steps and screen are as below :''' |
+ | |||
+ | [[File:ROM-2620 CAN Bus.png|RTENOTITLE]] | ||
+ | |||
+ | Step 4: Follow the figure (step1 - step4). If B node received data means test successful. | ||
| | ||
− | [[File: | + | ==== '''QSPI''' ==== |
+ | |||
+ | Step 1: After select the test mode ‘Q’ to verify QSPI, you will see below screen. | ||
+ | |||
+ | [[File:ROM-2620 QSPI.png|RTENOTITLE]] | ||
− | + | Step 2: This test program will perform QSPI erase/write automatically and show ‘successfully’ when it’s done.<br/> Step 3: User can press any key to run again. | |
+ | | ||
− | + | | |
− | === ''' | + | ==== '''LPSPI''' ==== |
− | |||
− | + | Step 1: Two pcs rom-2620. One for ‘Master’ one for ‘Slave’.<br/> Step 2: Connection with these two boards by SPI Bus as below: | |
− | + | LPSPI3_PCS0 -- LPSPI3_PCS0<br/> LPSPI3_GND -- LPSPI3_GND<br/> LPSPI3_PCS1 -- LPSPI3_PCS1<br/> LPSPI3_SCK -- LPSPI3_SCK<br/> LPSPI3_SOUT -- LPSPI3_SIN<br/> LPSPI3_SIN -- LPSPI3_SOUT | |
− | < | ||
− | |||
− | |||
− | |||
− | + | Step 3: One board select mode ‘M’ to be Master.<br/> Step 4: The second board is specified to Slave by select mode ‘S’.<br/> Step 5: The test screen as below: | |
− | < | ||
− | |||
− | |||
− | |||
− | |||
− | + | [[File:ROM-2620 LPSPI.png|RTENOTITLE]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | Step 6: Press any key at terminal of node master, it will execute the test again. | |
− | |||
− | |||
− | |||
− | |||
− | + | | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | ''' | + | ==== '''LPUART''' ==== |
+ | Step 1: Change ROM-ED91 SW1203 to '01'.<br/> Step 2: Connect COM-B and COM-E to PC.<br/> Step 3: Set RTS/CTS flow control for COM-B in Putty.exe | ||
− | + | [[File:ROM-2620 M33 COMB.png|RTENOTITLE]] | |
− | + | Step 4: After select the test mode ‘U’ to verify LPUART2, you will see below screen. | |
− | + | [[File:ROM-2620 M33 LPUART.png|RTENOTITLE]] | |
− | + | Step 5: If tester can input any characters/strings and show that at COM-B means test successful. | |
− | + | === '''遠程訪問及文件傳輸(Remote Access and File Transimmion)''' === | |
− | + | ''' 查看主板IP位址 ( Chech IP Address ):''' | |
+ | <pre> Command : ifconfig | ||
+ | </pre> | ||
− | + | | |
− | + | ==== SSH访问及文件传输 ==== | |
− | + | SSH Remote Log into Device | |
− | + | *SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件) | |
+ | *需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码 | ||
− | + | [[File:ROM-2620 SSH.png|RTENOTITLE]] | |
− | + | = '''通用方法(General Method)''' = | |
− | + | === '''查看CPU温度(Check CPU Temperature)''' === | |
+ | <pre>root@imx8ulprom2620a1:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp | ||
+ | 37000 </pre> | ||
− | + | === '''查看内存容量(Check Memory Capacity)''' === | |
+ | <pre>root@imx8ulprom2620a1:~# free -h | ||
+ | total used free shared buff/cache available | ||
+ | Mem: 895Mi 230Mi 469Mi 29Mi 195Mi 546Mi | ||
+ | Swap: 0B 0B 0B | ||
+ | root@imx8ulprom2620a1:~# | ||
+ | </pre> | ||
− | + | === '''查看存储容量(Check Storage Capacity)''' === | |
+ | <pre>root@imx8ulprom2620a1:~# df -hT | ||
+ | Filesystem Type Size Used Avail Use% Mounted on | ||
+ | /dev/root ext4 15G 3.9G 9.5G 30% / | ||
+ | devtmpfs devtmpfs 431M 4.0K 431M 1% /dev | ||
+ | tmpfs tmpfs 448M 0 448M 0% /dev/shm | ||
+ | tmpfs tmpfs 180M 20M 160M 11% /run | ||
+ | tmpfs tmpfs 4.0M 0 4.0M 0% /sys/fs/cgroup | ||
+ | tmpfs tmpfs 448M 76K 448M 1% /tmp | ||
+ | tmpfs tmpfs 448M 1.5M 447M 1% /var/volatile | ||
+ | tmpfs tmpfs 90M 4.0K 90M 1% /run/user/0 | ||
+ | /dev/mmcblk0p1 vfat 84M 32M 52M 38% /run/media/boot-mmcblk0p1 | ||
+ | /dev/mmcblk2p2 ext4 29G 11G 17G 40% /run/media/root-mmcblk2p2 | ||
+ | /dev/mmcblk2p1 vfat 84M 32M 52M 38% /run/media/boot-mmcblk2p1 | ||
+ | root@imx8ulprom2620a1:~# | ||
+ | </pre> | ||
− | + | | |
− | + | === '''設置RTC (RTC Setting) ''' === | |
+ | <pre>root@imx8ulprom2620a1:~# systemctl stop ntpdate.service | ||
+ | root@imx8ulprom2620a1:~# date 090816072021 && hwclock -w && date | ||
+ | Wed Sep 8 16:07:00 UTC 2021 | ||
+ | Wed Mar 6 04:31:37 UTC 2024 | ||
+ | root@imx8ulprom2620a1:~# date | ||
+ | Wed Mar 6 04:31:44 UTC 2024 | ||
+ | root@imx8ulprom2620a1:~#</pre> | ||
− | + | | |
− | + | 查看系統時間 (Check the system) | |
− | + | root@imx8ulprom2620a1:/# timedatectl<br/> [ 41.402592] kauditd_printk_skb: 6 callbacks suppressed<br/> [ 41.402611] audit: type=1334 audit(45.332:16): prog-id=15 op=LOAD<br/> [ 41.417884] audit: type=1334 audit(45.344:17): prog-id=16 op=LOAD<br/> Local time: Thu 1970-01-01 00:00:46 UTC<br/> Universal time: Thu 1970-01-01 00:00:46 UTC <br/> RTC time: Thu 1970-01-01 00:00:45 <----- Real-Time Clock,RTC <br/> Time zone: Universal (UTC, +0000) <------ Time zone 目前<br/> System clock synchronized: no<br/> NTP service: active<br/> RTC in local TZ: no ''' ''' | |
− | + | Note : | |
− | + | Change Time Zone | |
+ | <pre><code data-highlighted="yes">sudo timedatectl set-timezone "Asia/Taipei" | ||
+ | </code></pre> | ||
− | + | <code data-highlighted="yes"> Local time: Fri 2024-05-03 09:07:42 CST<br/> Universal time: Fri 2024-05-03 01:07:42 UTC<br/> RTC time: Fri 2024-05-03 09:07:42<br/> Time zone: Asia/Taipei (CST, +0800)<br/> System clock synchronized: yes<br/> NTP service: active<br/> RTC in local TZ: yes</code> | |
− | + | Time Zone List | |
− | + | | |
− | + | $ sudo timedatectl list-timezones | |
− | + | Africa/Abidjan | |
− | + | Africa/Accra | |
− | + | Africa/Addis_Ababa | |
− | + | Africa/Algiers | |
− | + | Africa/Asmara | |
− | + | Africa/Bamako | |
− | + | Africa/Bangui | |
− | + | Africa/Banjul | |
− | + | Africa/Bissau | |
− | + | Africa/Blantyre | |
− | + | Africa/Brazzaville | |
− | + | Africa/Bujumbura | |
− | + | Africa/Cairo | |
− | + | Africa/Casablanca | |
− | + | = '''Linux BSP編譯方法(Linux BSP Compile Method)''' = | |
− | + | === '''[http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVD_User_Guide Yocto 4.2]''' === | |
− | + | === [http://ess-wiki.advantech.com.tw/view/IoTGateway/BSP/Linux/iMX8/Yocto_LBVC_User_Guide '''Yocto 4.0'''] === | |
− | |||
− | |||
− |
Latest revision as of 09:15, 10 May 2024
Contents
- 1 產品介紹
- 2 接口布局和尺寸(Layout and Sizes)
- 3 快速入门 (Quick Start)
- 4 Linux系统的基本使用(Linux System Basic Operating Method)
- 4.1 UUU 使用方法(USB Connection (OTG port))
- 4.2 Display Setting (ROM-2620)
- 4.3 Audio(Audio Testing Methid)
- 4.4 M.2 WiFi/BT測試方法(M.2 WiFi/BT Testing Method)
- 4.5 Serial Port測試方法(Serial Testing Method)(COM A/C)
- 4.6 I2C測試方法(I2C Testing Method)
- 4.7 USB測試方法(USB Testing Method)
- 4.8 RTC測試方法(RTC Testing Method)
- 4.9 eMMC/SD測使方法(eMMC/SD Testing Method)
- 4.10 乙太網路使用方法(Ethernent Testing Method)
- 4.11 GPIO使用方法(GPIO Operating Method)
- 4.12 Camera使用方法(Camera Testing Method)
- 4.13 PWM測試方法(PWM Testing Method)
- 4.14 M33 Function
- 4.15 遠程訪問及文件傳輸(Remote Access and File Transimmion)
- 5 通用方法(General Method)
- 6 Linux BSP編譯方法(Linux BSP Compile Method)
產品介紹
產品特性(Features)
- NXP Arm® Cortex®-A35 i.MX 8ULP Dual up to 1.0 GHz
- 1 x Arm Cortex-M33 core
- Onboard LPDDR4 1GB, 2000MT/s memory
- 1 x 4 lane MIPI-DSI 1 x USB2.0, 1 x USB 2.0 OTG, 5 x UART, 2 x I2C, 24 x GPIO, 6 x PWM, 1 x CAN
- Ultra small size form factor - OSM
- Support Ycoto Linux and Microsoft Azure Sphere OS
產品官網連結(Product information Link)
接口布局和尺寸(Layout and Sizes)
ROM-2620 接口布局圖 Board Dimension Layout
ROM-ED91 接口布局圖 Board Dimension Layout
主板内置插针式引脚排序方式 (Pin Header defination)
Internal I/O, Jummper/Switch List:
Label | Function | Label | Function |
DCIN1401 | 12V DCIN connector | SW1301 | BT0_CFG1/4, BT1_CFG6/7/9/11 |
COMB | RS232/422/485 | SW1302 | BT0_CFG0, BT1_CFG4/5, BOOT_SEL0#/1#, MOD_ON |
COMA | RS232/422/485 | SW1203 | UARTB_MODE0, UART_MODE1 |
LAN | LAN Connector | SW1204 | UARTB_TERM, UARTB_SLEW |
USB1 | USB2.0 port Connector | SW1206 | U1205_RX_TERM, U1205_MODE2 |
USB0_OTG1 | Micro USB Connector | SW1201 | UARTA_MODE0, UART_MODE1 |
AJ | Line Out Connector | SW1202 | UARTA_TERM, UARTA_SLEW |
MIC | MIC Connector | SW1205 | U1202_RX_TERM, U1202_MODE2 |
CAN | CAN Bus Connector | SW1303 | Power button |
COME_DEBUG | M-core debug console | SW1304 | Reset button |
COMC | COM | I2S_CN | I2S Connector |
COMD | A-core debug console | CN501 | CAN0_H, CAN0_L terminatl resistors |
I2C1101 | I2C Connector | SD_SLT | SD select |
I2C1102 | I2C Connector | GPIO1101 | GPIO header |
CN601 | M.2 Key E Connector | SPI_CN1101 | PWM header |
CN701 | MIPI-CSI Connector | CN1101 | SPI header |
LVDS | LVDS Connector | LVDS_VDD_SLT | LVDS power select select header |
LVDS_BKLT_PWR | LVDS Backlight Connector | LVDS_BKLT_SLT | LVDS Backlight power select header |
BAT1 | Battery Connector |
Rear I/O
LED Function List
Location | Function |
PD1405 | +V5_MOD |
PD1502 | +V3.3 |
PD1503 | +V5 |
Switch Settings
- SW1301(BT0_CFG1/4, BT1_CFG6/7/9/11)
- SW1302(BT0_CFG0, BT1_CFG4/5, BOOT_SEL0#/1#, MOD_ON)
- SW1203 (UARTB_MODE0, UART_MODE1)
- SW1204 (UARTB_TERM,_UARTB_SLEW)
- SW1206_(U1205_RX_TERM,_U1205_MODE2)
- SW1201 (UARTA_MODE0, UART_MODE1)
- SW1202 (UARTA_TERM,_UARTA_SLEW)
- SW1205_(U1202_RX_TERM,_U1202_MODE2)
- SW1303_(Power_button)
- SW1304_(Reset_button)
- SD_SLT_(SD_select)
- LVDS_VDD_SLT_(LVDS_power_select_select_header)
- LVDS_BKLT_SLT_(LVDS_Backlight_power_select_header)
接口引脚定義 (Connector Pin definitions)
- DCIN1401
- COMB
- COMA
- LAN
- USB1
- USB0_OTG1
- AJ(Audio_Jack)
- MIC
- CAN
- COME_DEBUG(M-core_debug)
- COMC
- COMD(A-code_debug)
- I2C1101
- I2C1102
- CN601(M.2_Key_E)
- CN701(MIPI-CSI)
- LVDS
- LVDS_BKLT_PWR
- BAT1
- I2S_CN(I2S)
- CN501(CAN0_H/CAN0_L)
- GPIO1101
- SPI_CN1101(PWM)
- CN1101(SPI)
机械尺寸 (Mechanical Characteristics)
ROM-2620
快速入门 (Quick Start)
系统下载 (OS Download)
- 'Linux系统 (Linux OS)'
Yocto 4.0: IoTGateway/BSP/Linux/iMX8/OS Support List 4.0 release ROM-2620 - ESS-WIKI (advantech.com.tw)
Yocto 4.2: IoTGateway/BSP/Linux/iMX8/OS Support List 4.2 release ROM-2620 - ESS-WIKI (advantech.com.tw)
Linux 燒錄方法 (Linux Flash eMMC Method)
使用Flash tool 燒錄鏡像到eMMC (Flash image into eMMC by Flash Tools)
Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system)
Step1: 創造一張可開機的SD 卡 (Create a bootable SD card)
Command :
~$ sudo dd if=2620A1AIM34LIVC0054_iMX8ULP_1G_flash_tool/image/imx-image-full-imx8ulprom2620a1-20230627062759.rootfs.wic of=/dev/sde bs=1M conv=fsync status=progress
Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot)
Step3: 確認開機選擇指撥開關
EMMC boot: | SW1301: 1_2_5_6 ON SW1302: 4_6 ON |
SD boot: | SW1301: 1_2_3_4 ON SW1302: 4_6 ON |
Serial download: | SW1301: All OFF SW1302: 5_6 ON |
Step4:打開電源 和 終端機 (Turn on the Power & Terminal)
Step5: 複製flash tool到U盤中, 解壓縮flash tools檔案,(copy to USB Disk, then unzip the flash tools file)(Test with 32G SD card)
複製檔案到U盤中 (Copy the flash file to USB Disk), 解壓縮flash tool到home目錄(Unzip the file to home)
- tar zxvf /run/media/New\ Volume-sda/2620A1AIM34LIVC0054_iMX8ULP_1G_flash_tool.tgz -C ~
5. 進入flsah tool下的mk_inand資歷夾, 執行指令./mksd-linux.sh /dev/mmcblk0燒錄image到eMMC(Connect USB Disk to ROM-2620 system, extract the flash tool and browser to mk_inand folder and execute flash shell script "./mksd-linux.sh /dev/mmcblk0"
解壓縮後如果沒有mksd-linux.sh檔案, 可以到以下連結下載並複製到mk_inand資料夾下(If there is no mksd-linux.sh file in mk_inand directory. Please download from the link below and place it in mk_inand directory:
ROM-2620 | Device node |
SD card | /dev/mmcblk2 |
eMMC | /dev/mmcblk0 |
6. 切換開機switch來設定成從eMMC開機(Change boot switch to boot from eMMC. Reboot system).
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Check the Sriel port in Device Manager (查看PC端的串口号):
if you can not identify the Serial device , please check your serial driver.
Debug port connection (串口連接)
Log into Terminal Tool (进入串口调试终端):
Linux系统的基本使用(Linux System Basic Operating Method)
UUU 使用方法(USB Connection (OTG port))
Connect USB cable to USB OTG port.
Change boot switch to "SW1301 all OFF, SW1302: 5_6:on" to boot from force recovery mode.
Serial download: | SW1301: All OFF SW1302: 5_6 ON |
Download uuu tool from link below:
Releases · nxp-imx/mfgtools (github.com)
The uuu verison we tested is 1.4.193: uuu
uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.193-0-ge56424c
Perpare uboot and image files below:
2620A1AIM34LIVC0064_iMX8ULP_1G_imx-boot.tgz
2620A1AIM34LIVC0064_iMX8ULP_1G_flash_tool.tgz
1. Download uuu
$ chmod a+x uuu
$ tar zxvf 2620A1AIM34LIVC0064_iMX8ULP_1G_imx-boot.tgz
$ tar zxvf 2620A1AIM34LIVC0064_iMX8ULP_1G_flash_tool.tgz
Type command below to flash eMMC:
Display Setting (ROM-2620)
U-boot Command :
- Display
=> saveenv
=> boot
Audio(Audio Testing Methid)
0 [sgtl5000 ]: sgtl5000 - sgtl5000
sgtl5000
# amixer set Lineout 100%
# amixer set PCM 100%
Record and playback:
M.2 WiFi/BT測試方法(M.2 WiFi/BT Testing Method)
- Test Wi-Fi with EWM-W167 on C0048 version: Change SD_SLT to 2-3
=> saveenv
=> boot
In Linux user space:
# ifconfig wlan0 up
# iwlist wlan0 scan | grep ESSID
# killall wpa_supplicant
# ifconfig wlan0 up
# wpa_passphrase "Pilimao" "0913079939" > /tmp/wpa.conf
# wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
# udhcpc -b -i wlan0
# ping 8.8.8.8
Add name server: nameserver 8.8.8.8 in resolv.conf file
# ping google.com
Test BT:
# ./start_bt.sh ttyLP0
# hciconfig hci0 up
# hciconfig
# bluetoothctl
# discoverable on
# pairable on
# scan on
# info 84:C5:A6:D3:AF:E4
# pair 84:C5:A6:D3:AF:E4
# connect 84:C5:A6:D3:AF:E4
# paired-devices
# disconnect 84:C5:A6:D3:AF:E4
# remove 84:C5:A6:D3:AF:E4
- Test Wi-Fi with EWM-W194M201E Module (SDIO Interface)
Step 1: Press enter after boot. The system will stop at u-boot, and change dtb file by below command.
=> saveenv
=> boot
Step 2: Install driver by below command.
# modprobe moal mod_para=nxp/wifi_mod_para.conf
# modprobe btnxpuart
Step 3: WIFI test command.
# wpa_passphrase ASUS-917C qwert12345 > /tmp/wpa.conf
# wpa_supplicant -d -B -i mlan0 -c /tmp/wpa.conf
# udhcpc -i mlan0
- Test Bluetooth with EWM-W194M201E Module (UART Interface)
Step 1: Please refer to above step 1.
Step 2: Please refer to above step 2.
Step 3: Bluetooth test command.
# bluetoothctl
# discoverable on
# pairable on
# scan on
[NEW] FC:18:3C:8D:75:F4 myphone
# scan off
# pair FC:18:3C:8D:75:F4
# connect FC:18:3C:8D:75:F4
Serial Port測試方法(Serial Testing Method)(COM A/C)
COMA | /dev/ttyLP0 |
COMB(M33 Domain) | |
COMC | /dev/ttyLP2 |
COMD | /dev/ttyLP1 |
COME_DEBUG | M33 debug port |
- RS-232 Loopback Test (eg. COMA: ttyLP0):
Step 1: First change ROM-ED91 SW1201 to ‘01’.
Step 2: Run test command.
# cat /dev/ttyLP0 &
# echo test > /dev/ttyLP0
- RS-422 Test:
Step 1: First change ROM-ED91 SW1201 to ‘11’.
Step 2: Test RS-422 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following:
Adam-4520 RX- <-->ROM-2620 COMA DB9 Pin 1,
Adam-4520 RX+ <-->ROM-2620 COMA DB9 Pin 2,
Adam-4520 TX- <-->ROM-2620 COMA DB9 Pin 4,
Adam-4520 TX+ <--> ROM-2620 COMA DB9 Pin 3
Step 3: Run below command:
# cat /dev/ttyLP0 &
# echo "Serial Test" > /dev/ttyLP0
- RS-485 Test:
Step 1: First change ROM-ED91 SW1201 to ‘10’.
Step 2: Test RS-485 with Adam-4520. Connect Adam-4520 with COMA with DB9 as the following:
Adam-4520 Data- <-->ROM-2620 COMA DB9 Pin 1,
Adam-4520 Data+ <-->ROM-2620 COMA DB9 Pin 2
Step 3: Run below command:
# cat /dev/ttyLP0 &
# echo "Serial Test" > /dev/ttyLP0
I2C測試方法(I2C Testing Method)
Step 1: Plug in ROM-EG70
Step 2: Test by below command (eg. I2C-6 I2C_1101):
# echo -n $'\x06\x05\x04\x03\x02\x01' > test
# dd if=test of=/sys/bus/i2c/devices/6-0050/eeprom
# hexdump -C /sys/bus/i2c/devices/6-0050/eeprom -n 64
USB測試方法(USB Testing Method)
USB disk test (USB 2.0)
Step 1: Issue the following command (lsusb -t) after inserting a USB disk into the USB 2.0 port to check if the USB device is listed. Step 2: Test (eg. if usb disk is /dev/sda)
# dd if=/dev/sda of=backup bs=1 count=1024 skip=4096 # dd if=data of=/dev/sda bs=1 seek=4096
# dd if=/dev/sda of=data1 bs=1 count=1024 skip=4096 # diff data data1
# dd if=backup of=/dev/sda bs=1 seek=4096
RTC測試方法(RTC Testing Method)
Step 1: Set system time to current, then write to RTC
Step 2: Set one incorrect time, then read time from RTC to verify
eMMC/SD測使方法(eMMC/SD Testing Method)
Device Routes
eMMC: /dev/mmcblk0
SD: /dev/mmcblk2
Test (eg. emmc)
Step 1: Test command:
# dd if=/dev/mmcblk0 of=backup bs=1 count=1024 skip=4096
# dd if=data of=/dev/mmcblk0 bs=1 seek=4096
# dd if=/dev/mmcblk0 of=data1 bs=1 count=1024 skip=4096
# diff data data1
# dd if=backup of=/dev/mmcblk0 bs=1 seek=4096
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
Command: Ping - I eth1 8.8.8.8 or Ping - I eth0 8.8.8.8
GPIO使用方法(GPIO Operating Method)
GPIO pin:
GPIO1101 pin | Pin Name | CPU Ball Name | GPIO number |
1 | GPIO_A_0 | PTC0 | 416 |
2 | GPIO_A_1 | PTC1 | 417 |
3 | GPIO_A_2 | PTC2 | 418 |
4 | GPIO_A_3 | PTC3 | 419 |
5 | GPIO_A_4 | PTC4 | 420 |
6 | GPIO_A_5 | PTC12 | 428 |
7 | GPIO_B_0 | PTC18 | 434 |
8 | GPIO_B_1 | PTC19 | 435 |
9 | GPIO_B_2 | PTC20 | 436 |
10 | GPIO_B_3 | PTC21 | 437(Use for M2_SDIO_RST) |
11 | GPIO_B_4 | PTC22 | 438(Use for M2_W_DISABLE2) |
12 | GPIO_B_5 | PTC23 | 439(Use for M2_W_DISABLE1) |
13 | GPIO_B_6 | PTB0 | 448 |
14 | GPIO_B_7 | PTB1 | 449 |
15 | GPIO_C_0 | PTD12 | 140 |
16 | GPIO_C_1 | PTD13 | 141 |
17 | GPIO_C_2 | PTF1 | 193 |
18 | GPIO_C_3 | PTF7 | 199(Use for LVDS_Bridge_RST) |
19 | PTB6 | PTB6 | 454 |
20 | PTA5 | PTA5 | 485 |
GPIO Loopback Test (Using GPIO1 and GPIO2 as examples)
Step 1: Connect GPIO1 and GPIO2
Step 2: Export GPIO interface
# echo 417 > /sys/class/gpio/export
Step 3: Set GPIO direction
# echo in > /sys/class/gpio/gpio2/direction
Step 4: Read value and set output value than check
# echo 1 > /sys/class/gpio/gpio1/value
# cat /sys/class/gpio/gpio2/value
1
Camera使用方法(Camera Testing Method)
MIPI-CSI0 (Tested with OV5640 + mini-SAS to MIPI-CSI Cable): OV5640 CSI (CN701): Connect OV5640 camera to EG-55 CAM3
Step 1: Take pictures
Step 2: View on panel
PWM測試方法(PWM Testing Method)
Please use oscilloscope to check waveform.
PWM1:
# echo 1000000 > /sys/class/pwm/pwmchip0/pwm4/period
# echo 500000 > /sys/class/pwm/pwmchip0/pwm4/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip0/pwm4/enable
PWM2:
# echo 1000000 > /sys/class/pwm/pwmchip6/pwm5/period
# echo 500000 > /sys/class/pwm/pwmchip6/pwm5/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip6/pwm5/enable
PWM3:
# echo 1000000 > /sys/class/pwm/pwmchip6/pwm2/period
# echo 500000 > /sys/class/pwm/pwmchip6/pwm2/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip6/pwm2/enable
PWM4:
# echo 1000000 > /sys/class/pwm/pwmchip6/pwm3/period
# echo 500000 > /sys/class/pwm/pwmchip6/pwm3/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip6/pwm3/enable
PWM5:
# echo 1000000 > /sys/class/pwm/pwmchip6/pwm4/period
# echo 500000 > /sys/class/pwm/pwmchip6/pwm4/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip6/pwm4/enable
M33 Function
We use default M-core firmware to verify each of IO feature. User should connect COME_DEBUG port to PC and there were show screen as demonstration below:
Press C for test mode of CAN bus
Press Q for test mode of QSPI
Press M for test mode of LPSPI master
Press S for test mode of LPSPI slave
Press U for test mode of LPUART
About this firmware, user should note that if you want to switch to another test mode, you must reboot the system.
CAN Bus
Step 1: Prepare two pcs rom-2620. One for ‘Node A’ one for ‘Node B’
Step 2: Connect these two boards (HI-HI/LO-LO)
Step 3: The test steps and screen are as below :
Step 4: Follow the figure (step1 - step4). If B node received data means test successful.
QSPI
Step 1: After select the test mode ‘Q’ to verify QSPI, you will see below screen.
Step 2: This test program will perform QSPI erase/write automatically and show ‘successfully’ when it’s done.
Step 3: User can press any key to run again.
LPSPI
Step 1: Two pcs rom-2620. One for ‘Master’ one for ‘Slave’.
Step 2: Connection with these two boards by SPI Bus as below:
LPSPI3_PCS0 -- LPSPI3_PCS0
LPSPI3_GND -- LPSPI3_GND
LPSPI3_PCS1 -- LPSPI3_PCS1
LPSPI3_SCK -- LPSPI3_SCK
LPSPI3_SOUT -- LPSPI3_SIN
LPSPI3_SIN -- LPSPI3_SOUT
Step 3: One board select mode ‘M’ to be Master.
Step 4: The second board is specified to Slave by select mode ‘S’.
Step 5: The test screen as below:
Step 6: Press any key at terminal of node master, it will execute the test again.
LPUART
Step 1: Change ROM-ED91 SW1203 to '01'.
Step 2: Connect COM-B and COM-E to PC.
Step 3: Set RTS/CTS flow control for COM-B in Putty.exe
Step 4: After select the test mode ‘U’ to verify LPUART2, you will see below screen.
Step 5: If tester can input any characters/strings and show that at COM-B means test successful.
遠程訪問及文件傳輸(Remote Access and File Transimmion)
查看主板IP位址 ( Chech IP Address ):
Command : ifconfig
SSH访问及文件传输
SSH Remote Log into Device
- SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
- 需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
root@imx8ulprom2620a1:~# cat /sys/devices/virtual/thermal/thermal_zone0/temp 37000
查看内存容量(Check Memory Capacity)
root@imx8ulprom2620a1:~# free -h total used free shared buff/cache available Mem: 895Mi 230Mi 469Mi 29Mi 195Mi 546Mi Swap: 0B 0B 0B root@imx8ulprom2620a1:~#
查看存储容量(Check Storage Capacity)
root@imx8ulprom2620a1:~# df -hT Filesystem Type Size Used Avail Use% Mounted on /dev/root ext4 15G 3.9G 9.5G 30% / devtmpfs devtmpfs 431M 4.0K 431M 1% /dev tmpfs tmpfs 448M 0 448M 0% /dev/shm tmpfs tmpfs 180M 20M 160M 11% /run tmpfs tmpfs 4.0M 0 4.0M 0% /sys/fs/cgroup tmpfs tmpfs 448M 76K 448M 1% /tmp tmpfs tmpfs 448M 1.5M 447M 1% /var/volatile tmpfs tmpfs 90M 4.0K 90M 1% /run/user/0 /dev/mmcblk0p1 vfat 84M 32M 52M 38% /run/media/boot-mmcblk0p1 /dev/mmcblk2p2 ext4 29G 11G 17G 40% /run/media/root-mmcblk2p2 /dev/mmcblk2p1 vfat 84M 32M 52M 38% /run/media/boot-mmcblk2p1 root@imx8ulprom2620a1:~#
設置RTC (RTC Setting)
root@imx8ulprom2620a1:~# systemctl stop ntpdate.service root@imx8ulprom2620a1:~# date 090816072021 && hwclock -w && date Wed Sep 8 16:07:00 UTC 2021 Wed Mar 6 04:31:37 UTC 2024 root@imx8ulprom2620a1:~# date Wed Mar 6 04:31:44 UTC 2024 root@imx8ulprom2620a1:~#
查看系統時間 (Check the system)
root@imx8ulprom2620a1:/# timedatectl
[ 41.402592] kauditd_printk_skb: 6 callbacks suppressed
[ 41.402611] audit: type=1334 audit(45.332:16): prog-id=15 op=LOAD
[ 41.417884] audit: type=1334 audit(45.344:17): prog-id=16 op=LOAD
Local time: Thu 1970-01-01 00:00:46 UTC
Universal time: Thu 1970-01-01 00:00:46 UTC
RTC time: Thu 1970-01-01 00:00:45 <----- Real-Time Clock,RTC
Time zone: Universal (UTC, +0000) <------ Time zone 目前
System clock synchronized: no
NTP service: active
RTC in local TZ: no
Note :
Change Time Zone
<code data-highlighted="yes">sudo timedatectl set-timezone "Asia/Taipei" </code>
Local time: Fri 2024-05-03 09:07:42 CST
Universal time: Fri 2024-05-03 01:07:42 UTC
RTC time: Fri 2024-05-03 09:07:42
Time zone: Asia/Taipei (CST, +0800)
System clock synchronized: yes
NTP service: active
RTC in local TZ: yes
Time Zone List
$ sudo timedatectl list-timezones
Africa/Abidjan
Africa/Accra
Africa/Addis_Ababa
Africa/Algiers
Africa/Asmara
Africa/Bamako
Africa/Bangui
Africa/Banjul
Africa/Bissau
Africa/Blantyre
Africa/Brazzaville
Africa/Bujumbura
Africa/Cairo
Africa/Casablanca