Difference between revisions of "How to use UART RK3568"
Yunjin.jiang (talk | contribs) |
Yanwei.cao (talk | contribs) (remove dummy setenv cmd) |
||
(4 intermediate revisions by one other user not shown) | |||
Line 49: | Line 49: | ||
| | ||
+ | |||
== KEDGE-350 Borad == | == KEDGE-350 Borad == | ||
− | |||
− | + | '''Main Board''' | |
− | + | ||
− | + | {| border="1" cellpadding="1" cellspacing="1" | |
− | + | |- | |
− | + | | '''COM Name''' | |
− | + | | '''Device Node''' | |
− | + | | '''Remark''' | |
− | + | |- | |
− | + | | COM0 | |
− | + | | /dev/ttyS3 | |
− | + | | RS232 2-wire and RS485 | |
− | + | |- | |
− | + | | COM1 | |
− | + | | /dev/ttyS4 | |
− | + | | RS232 2-wire and RS485 | |
− | + | |- | |
− | + | | COM2(UIO) | |
− | + | | /dev/ttyS7 | |
− | + | | RS232 2-wire | |
− | + | |- | |
− | + | | COM3(UIO) | |
− | + | | /dev/ttyS8 | |
− | + | | RS232 2-wire | |
− | + | |} | |
− | + | ||
− | + | '''Note : ''' | |
− | + | ||
− | + | 1. Only COM0 and COM1 support RS485 mode. | |
− | + | ||
− | + | | |
− | + | ||
− | + | '''UIO-4031''' | |
− | + | ||
− | + | {| border="1" cellpadding="1" cellspacing="1" | |
− | + | |- | |
− | + | | '''COM Name''' | |
− | + | | '''Device Node''' | |
− | + | | '''Remark''' | |
+ | |- | ||
+ | | COM0 | ||
+ | | /dev/ttyUSB2 | ||
+ | | RS485 | ||
+ | |- | ||
+ | | COM1 | ||
+ | | /dev/ttyUSB3 | ||
+ | | RS485 | ||
+ | |- | ||
+ | | COM2 | ||
+ | | /dev/ttyUSB0 | ||
+ | | RS485 | ||
+ | |- | ||
+ | | COM3 | ||
+ | | /dev/ttyUSB1 | ||
+ | | RS485 | ||
+ | |- | ||
+ | | COM4 | ||
+ | | /dev/ttyS7 | ||
+ | | RS232 2-wire | ||
+ | |- | ||
+ | | COM5 | ||
+ | | /dev/ttyS8 | ||
+ | | RS232 2-wire | ||
+ | |} | ||
+ | |||
+ | | ||
+ | |||
+ | |||
== ROM-5880 Borad == | == ROM-5880 Borad == | ||
− | |||
− | + | {| border="1" cellpadding="1" cellspacing="1" | |
− | + | |- | |
− | + | | '''COM Name''' | |
− | + | | '''Device Node''' | |
− | + | | '''Remark''' | |
− | + | |- | |
− | + | | COM1 | |
− | + | | /dev/ttyS3 | |
− | + | | RS232 4-wire | |
− | + | |- | |
− | + | | COM2 | |
− | + | | /dev/ttyS5 | |
− | + | | RS232 2-wire | |
− | + | |- | |
− | + | | COM3 | |
− | + | | /dev/ttyS4 | |
− | + | | RS232 4-wire | |
− | + | |- | |
− | + | | COM4 | |
− | + | | /dev/ttyS7 | |
− | + | | RS232 2-wire | |
− | + | |} | |
− | + | ||
− | + | '''Note : ''' | |
− | + | ||
− | + | | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
= How to config RS232 or RS485 mode = | = How to config RS232 or RS485 mode = | ||
Line 145: | Line 161: | ||
Then you can input the following cammand to config UART mode. | Then you can input the following cammand to config UART mode. | ||
+ | |||
== Config Uart coming from cpu == | == Config Uart coming from cpu == | ||
Line 154: | Line 171: | ||
'''RS232 Mode(Taking Kedge-350 for example):''' | '''RS232 Mode(Taking Kedge-350 for example):''' | ||
− | <pre> | + | <pre>setenv uart_mode_cpu 3:0,4:0 |
saveenv | saveenv | ||
reset | reset | ||
</pre> | </pre> | ||
+ | '''Note :''' | ||
− | + | The default value is RS485 for Kedge-350. | |
− | |||
− | The default value is | ||
Above command "uart_mode_cpu 3:1,4:1", 3:1 means set ttyS3 to RS485(0 means to RS232; 1 means to RS485). | Above command "uart_mode_cpu 3:1,4:1", 3:1 means set ttyS3 to RS485(0 means to RS232; 1 means to RS485). | ||
If you just want ttyS3(or ttyS4)to be RS485 mode, please change "3:1,4:1"to "3:1,4:0"(or "3:0,4:1"). | If you just want ttyS3(or ttyS4)to be RS485 mode, please change "3:1,4:1"to "3:1,4:0"(or "3:0,4:1"). | ||
− | |||
− | |||
== Config Uart coming from cp2108 == | == Config Uart coming from cp2108 == |
Latest revision as of 11:25, 22 May 2024
Contents
Overview
The Android/Linux UART/serial port access from user is through the tty-devices. The tty-devices have different names depending on UART driver on different board.
RS-485
RS-485 uses half-duplex communication, which means that one medium is shared for transmitting and receiving data.
Therefore the system needs to control the RS-485 transceiver's transmit mode.
Usually the UART RTS signal is used to switch the transmitter on and off.
Boards
RSB-4810 Borad
COM Name | Device Node | Remark |
COM1 | /dev/ttyS4 | RS232 2-wire |
COM2 | /dev/ttyS7 | RS232 2-wire |
COM3 | /dev/ttyUSB2 | RS232 4-wire and RS485 |
COM4 | /dev/ttyUSB3 | RS232 4-wire and RS485 |
COM5 | /dev/ttyUSB0 | RS232 4-wire |
COM6 | /dev/ttyUSB1 | RS232 4-wire |
Note :
KEDGE-350 Borad
Main Board
COM Name | Device Node | Remark |
COM0 | /dev/ttyS3 | RS232 2-wire and RS485 |
COM1 | /dev/ttyS4 | RS232 2-wire and RS485 |
COM2(UIO) | /dev/ttyS7 | RS232 2-wire |
COM3(UIO) | /dev/ttyS8 | RS232 2-wire |
Note :
1. Only COM0 and COM1 support RS485 mode.
UIO-4031
COM Name | Device Node | Remark |
COM0 | /dev/ttyUSB2 | RS485 |
COM1 | /dev/ttyUSB3 | RS485 |
COM2 | /dev/ttyUSB0 | RS485 |
COM3 | /dev/ttyUSB1 | RS485 |
COM4 | /dev/ttyS7 | RS232 2-wire |
COM5 | /dev/ttyS8 | RS232 2-wire |
ROM-5880 Borad
COM Name | Device Node | Remark |
COM1 | /dev/ttyS3 | RS232 4-wire |
COM2 | /dev/ttyS5 | RS232 2-wire |
COM3 | /dev/ttyS4 | RS232 4-wire |
COM4 | /dev/ttyS7 | RS232 2-wire |
Note :
How to config RS232 or RS485 mode
Enter U-boot interrupt mode
Connect device to debug port, and open debug console. See more How_to_debug.
Press "ctrl + c" key before power up the device, until get the following information on debug console :
Hit any key to stop autoboot: 0 => <INTERRUPT> =>
Then you can input the following cammand to config UART mode.
Config Uart coming from cpu
RS485 Mode(Taking Kedge-350 for example):
setenv uart_mode_cpu 3:1,4:1 saveenv reset
RS232 Mode(Taking Kedge-350 for example):
setenv uart_mode_cpu 3:0,4:0 saveenv reset
Note :
The default value is RS485 for Kedge-350.
Above command "uart_mode_cpu 3:1,4:1", 3:1 means set ttyS3 to RS485(0 means to RS232; 1 means to RS485).
If you just want ttyS3(or ttyS4)to be RS485 mode, please change "3:1,4:1"to "3:1,4:0"(or "3:0,4:1").
Config Uart coming from cp2108
RS485 Mode:
setenv uart_mode 0x0c saveenv reset
RS232 Mode:
setenv uart_mode 0x00 saveenv reset
Note :
The default value is RS232.
Cp210x support four port, but RSB4810 Only ttyUSB2 and ttyUSB3 support RS485 mode.
Above command "setenv uart_mode 0x0c", 0x0c means set bit2(ttyUSB2) and bit3(ttyUSB3) to 1 (0 means to RS232; 1 means to RS485).
If you just want ttyUSB2 (or ttyUSB3)to be RS485 mode, please change 0x0c to 0x04 (or 0x08).