Difference between revisions of "RSB-3430 user guide"
Line 336: | Line 336: | ||
− | === ''' | + | === '''3G使用方法(3G Testing Method)''' === |
<pre>Command: | <pre>Command: | ||
− | + | 3G (Telit HE910D) | |
− | + | pppd connect 'chat -v -s -t 10 "" "AT" "" "ATDT*99#" "CONNECT" ""' user username password password /dev/ttyACM3 460800 nodetach crtscts debug usepeerdns defaultroute & | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</pre> | </pre> | ||
− | |||
− | |||
− | |||
− | |||
=== '''GPIO使用方法(GPIO Operating Method)''' === | === '''GPIO使用方法(GPIO Operating Method)''' === |
Revision as of 07:37, 27 October 2021
Contents
- 1 資源特性(Features)
- 2 訂購資訊(Ordering Information)
- 3 规格(Specifications)
- 4 接口布局和尺寸(Layout and Sizes)
- 5 'Connector List'
- 6 快速入门 (Quick Start)
- 7 Linux 燒錄方法 (Linux Flash eMMC Method)
- 8
- 9 Linux系统的基本使用(Linux System Basic Operating Method)
- 9.1 載入預設值由uboot 設定(Load Default Setting in Uboot )
- 9.2 顯示設定 (Display Setting )
- 9.3 乙太網路使用方法(Ethernent Testing Method)
- 9.4 WiFi & BT 使用方法(WIFI & Bluetooth Testing Method)
- 9.5 3G使用方法(3G Testing Method)
- 9.6 GPIO使用方法(GPIO Operating Method)
- 9.7 串口使用方法(Serial Port Operating Method)
- 9.8 蓝牙使用方法(BlueTooth Operating Method)
- 9.9 遠程訪問及文件傳輸(Remote Access and File Transimmion)
- 10 通用方法(General Method)
- 11 Linux BSP編譯方法(Android BSP Compile Method)
資源特性(Features)
- NXP Arm® Cortex®-A53 i.MX8M Plus Quad/Dual up to 1.8 GHz
- Onboard LPDDR4 4 GB / 6 GB, 4000MT/s memory
- HDMI 1920x1080 at 60Hz, 1 Single or 1 Dual Channel 24 bit LVDS (or 1 4-Lane MIPI-DSI by BOM Option)
- 1 4-wire RS-232/422/485, 1 USB3.2 Gen1 By 1, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out
- 1 mini-PCIe for 3G/4G, 1 M.2 2230 Key E Slot
- Supports Yocto Linux and Android
- Support I/O Expansions boards by UIO40-Express
訂購資訊(Ordering Information)
规格(Specifications)
接口布局和尺寸(Layout and Sizes)
接口布局圖 Board Dimension Layout
'Connector List'
BAT | RTC Battery Connector |
BL1 | LVDS Backlight 1 |
BL2 | LVDS Backlight 2 |
COM1 | COM + CAN Pin Header (default as debug console) |
CSI1 | MIPI-CSI Camera Input 1 |
CSI2 | MIPI-CSI Camera Input 2 |
DCIN/DCIN 1 | 12V DC Power Inout by DC Jack / by Pin Header |
HDMI | HDMI CONN |
LAN1 | Ethernet 1 |
LAN2 | Ethernet 2 |
LOUT | Line Out Pin Header |
LVDS | LVDS CONN. |
M2 | M.2 Key E CONN. |
MIC | MIC In Pin Header |
MPCIE | Mini-PCIe CONN. |
RST | Rest Button |
SD | SD Slot |
UIO1 | UIO40-Express Pin Header 1 |
UIO2 | UIO40-Express Pin Header 2 |
USB1 | USB CONN. (USB 3.2 Gen 1 on TOP + USB 2.0 on BOT) |
接口引脚定義 (Pin definitions)
- BLP1
- BLP2
- VDD1
- SW1
- BAT (RTC Battery CONN.)
- BL1 (LVDS Backlight 1)
- BL2 (LVDS Backlight 2)
- COM1 (COM + CAN Pin Header): (default as debug console)
- CSI1 (MIPI-CSI Camera Input 1)
- CSI2 (MIPI-CSI Camera Input 2)
- DCIN/ DCIN1 (12V DC Power Input by DC Jack/ by Pin Header)
- HDMI (HDMI CONN.)
- LAN1 (Ethernet eth0)
- LAN2 (Ethernet eth1)
- LOUT (Line Out Pin Header)
- LVDS (LVDS CONN.)
- M2 (M.2 Key E CONN.)
- MIC (MIC In Pin Header)
- MPCIE (Mini-PCIe CONN.)
- RST (Reset Button)
- SD (SD Slot)
- SIM (SIM Slot)
- UIO1 (UIO40-Express Pin Header 1)
- UIO2 (UIO40-Express Pin Header 2)
- USB 1 (USB 3.2 Gen 1 on TOP + USB 2.0 on BOT)
- LED
机械尺寸 (Mechanical Characteristics)
快速入门 (Quick Start)
系统下载 (OS Download)
'Linux系统 (Linux OS)'
Git BSP Tag Version |
Product |
BSP/Image |
Date |
Alpha Release |
Beta Release |
MP Release |
Release Note |
Comment |
Release Owner |
imx6LBV90146 |
RSB-3430A1 | 3430A1AIM20LIV90146_DualQuad_2021-08-08.img.gz | 2021-08-08 | V |
- Baidu link for imx6 Yocto 2.5 BSP and Image Password:ra18
- Dropbox link for imx6 Yocto 2.5 BSP and Image
- Downloads 2.5
Linux 燒錄方法 (Linux Flash eMMC Method)
1. 確認SD 在Ubuntu 電腦中的代號
2. 先將鏡像燒錄到SD Card 中( Create a bootable SD card )
3.設定終端機(Set Debug Terminal)
Debug 串口調試 (Debug port Setting)
以 Tera Term 为例介绍如何使用串口调试功能
Baud Rate波特率:115200 Data 数据位:8 Parity 奇偶校验:无 Stop 停止位:1 Flow Control流控:无
Tera Term Tool
Check the Sriel port in Device Manager (查看PC端的串口号):
if you can not identify the Serial device , please check your serial driver.
4. 將SD card 插入機器
5. 檢查撥碼開關 ( 1 ON , 2 OFF)
6. 接上Debug Cable
7. 打開電源
8. 由終端機進入系統
9. 燒錄鏡像到 eMMC flash
將3430A1AIM20LIV90146_DualQuad_flash_tool.tgz 複製到U盤中,插入機器的USB Port
在系統中 ,確認USB中燒錄資料
在根目錄下 ,解壓縮
在mk_Inand 資料夾中執行 ./mksd-linux.sh
10. 移除SD 卡,從eMMC 開機.
Linux系统的基本使用(Linux System Basic Operating Method)
載入預設值由uboot 設定(Load Default Setting in Uboot )
1. 開機時 在五秒內按下空白鍵 ,進入Uboot
2. Command :
env default -a
saveenv
reset
顯示設定 (Display Setting )
預設值為: HDMI 輸出
乙太網路使用方法(Ethernent Testing Method)
Command : ifconfig
Command: Ping 8.8.8.8
WiFi & BT 使用方法(WIFI & Bluetooth Testing Method)
M.2 module (EWM-W162M201E) - WIFI / BT Function WIFI $ ifconfig mlan0 up $ wpa_passphrase ${SSID} ${WPA_KEY} > /tmp/wpa.conf $ wpa_supplicant -BDwext -imlan0 -c/tmp/wpa.conf $ udhcpc -b -i mlan0 BlueTooth $ /usr/libexec/bluetooth/bluetoothd -C & $ hciconfig hci0 up $ bluetoothctl $ discoverable on $ pairable on $ scan on [NEW] FC:18:3C:8D:75:F4 Device ID $ scan off $ pair FC:18:3C:8D:75:F4 $ connect FC:18:3C:8D:75:F4
3G使用方法(3G Testing Method)
Command: 3G (Telit HE910D) pppd connect 'chat -v -s -t 10 "" "AT" "" "ATDT*99#" "CONNECT" ""' user username password password /dev/ttyACM3 460800 nodetach crtscts debug usepeerdns defaultroute &
GPIO使用方法(GPIO Operating Method)
Loop-back Test (Take GPIO4 and GPIO5 as examples) Step 1: Connect GPIO4 and GPIO5 Step 2: Export GPIO interface root@imx8qxprom5620a1 : ~# echo 456 > /sys/class/gpio/export root@imx8qxprom5620a1 : ~# echo 452 > /sys/class/gpio/export Step 3: Set direction root@imx8qxprom5620a1 : ~# echo out > /sys/class/gpio/gpio1/direction root@imx8qxprom5620a1 : ~# echo in > /sys/class/gpio/gpio2/direction Step 4: Read value and set output value then check root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 0r oot@imx8qxprom5620a1 : ~# echo 1 > /sys/class/gpio/gpio1/value root@imx8qxprom5620a1 : ~# cat /sys/class/gpio/gpio2/value 1
串口使用方法(Serial Port Operating Method)
RS-232 Test
SW7 Setting (SW7設置)
蓝牙使用方法(BlueTooth Operating Method)
Command : $ hciconfig hci0 up $ bluetoothctl $ discoverable on $ pairable on $ scan on [NEW] FC:18:3C:8D:75:F4 myphone $ scan off $ pair FC:18:3C:8D:75:F4 $ connect FC:18:3C:8D:75:F4
遠程訪問及文件傳輸(Remote Access and File Transimmion)
查看主板IP位址 ( Chech IP Address ):
Command : ifconfig
Windows下SSH访问及文件传输
SSH Remote Log into Device
- SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
- 需要设置远程设备的IP、通讯端口(默认22)、通讯方式,登录后验证用户名密码
通用方法(General Method)
查看CPU温度(Check CPU Temperature)
root@imx8qxprom5620a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600 # 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°
查看CPU频率(Check CPU Frequency)
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq >> 900000 cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq >> 1200000
查看内存容量(Check Memory Capacity)
root@imx8qxprom5620a1:/# busybox free -m total used free shared buffers cached Mem: 1794920 516080 1278840 17252 9852 80292 -/+ buffers/cache: 425936 1368984 Swap: 0 0 0
查看存储容量(Check Storage Capacity)
root@imx8qxprom5620a1:/# busybox df -h Filesystem Size Used Available Use% Mounted on /dev/root 13.4G 1.7G 11.1G 13% / devtmpfs 395.8M 4.0K 395.8M 0% /dev tmpfs 876.4M 0 876.4M 0% /dev/shm tmpfs 876.4M 16.5M 859.9M 2% /run tmpfs 876.4M 0 876.4M 0% /sys/fs/cgroup tmpfs 876.4M 4.0K 876.4M 0% /tmp tmpfs 876.4M 280.0K 876.2M 0% /var/volatile /dev/mmcblk0p2 13.6G 1.7G 11.3G 13% /run/media/mmcblk0p2 /dev/mmcblk0p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk0p1 /dev/mmcblk1p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk1p1 tmpfs 175.3M 88.0K 175.2M 0% /run/user/0 root@imx8qxprom5620a1:/#
網路Ping測試(Ping Network Testing)
ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms
設置RTC (RTC Setting)
root@imx8qxprom5620a1:/# systemctl stop ntpdate.service root@imx8qxprom5620a1:/# date 090816072021 && hwclock -w && date Wed Sep 8 16:07:00 UTC 2021 Wed Sep 8 16:07:00 UTC 2021 root@imx8qxprom5620a1:/# date Wed Sep 8 16:07:06 UTC 2021 root@imx8qxprom5620a1:/#'''