Difference between revisions of "AIR 030 Development"

Revision as of 12:00, 18 July 2024

Flash Image

Change the SW2 to ON and press power button.
<img _fck_mw_filename="Recovery BT.png" _fck_mw_origimgheight="377" _fck_mw_origimgwidth="566" alt="Air030 recovery button.jpg" src="/wiki/images/c/c8/Recovery_BT.png" style="vertical-align:middle;" title="Air030 recovery button.jpg" width="400" />

$ sudo reboot --force forced-recovery

Connect a linux OS host wired AIR-030 with usb-otg cable.
In the Host PC, make sure the AIR-030 (NVidia Corp) has detectd.

[ubuntu@linux 11:55:43 ~]$ lsusb 
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0bda:0161 Realtek Semiconductor Corp. Mass Storage Device
Bus 001 Device 024: ID 0955:7223 NVidia Corp.
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Please Check there is 7223 NVidia Corp

Install dependency package on HOST:

 
$ sudo tools/l4t_flash_prerequisites.sh # For Debian-based Linux

or

$ sudo apt install build-essential python libxml2-utils abootimg sshpass binutils -y

For Jackpack 5.1.1
1.Extracted tarball file PS :

$ sudo tar -zxvf air030_image_XXXXXX.tar.gz
$ cd Linux_for_Tegra

2. Flash

$ sudo ./flash.sh -d rootfs/boot/tegra234-air030.dtb jetson-agx-orin-devkit mmcblk0p1​​

To NVME

$ sudo ./tools/kernel_flash/l4t_initrd_flash.sh --external-device nvme0n1p1 -c ./tools/kernel_flash/flash_l4t_external.xml -S 32GB --erase-all --showlogs jetson-agx-orin-devkit nvme0n1p1

For Jetpack 6.0
To EMMC

$ sudo ./flash.sh jetson-agx-orin-devkit mmcblk0p1

To NVME

$ $ sudo ./tools/kernel_flash/l4t_initrd_flash.sh --external-device nvme0n1p1 -p "-c ./bootloader/generic/cfg/flash_t234_qspi.xml" -c ./tools/kernel_flash/flash_l4t_t234_nvme.xml --showlogs --network usb0 jetson-agx-orin-devkit nvme0n1p1

倘若燒錄時遇到"Parsing board information failed"
若可以先正常開機，使用get_eeprom_crc取得crc

ubuntu@localhost:~$ chmod a+x get_eeprom_crc)
ubuntu@localhost:~$ sudo ./get_eeprom_crc 0

再透過i2cset寫入正確的crc值到EEPROM
參數 : I2C_BUS, EEPROM_SLAVE_ADDR, ADDRESS, VALUE

$ sudo i2cset -f -y 0 0x50 0xff 0x28

再重燒
若不能正常開機，先下底下指令燒一次，然後再更新CRC值

$ sudo SKIP_EEPROM_CHECK=1 BOARDSKU="0004" CHIP_SKU=00:00:00:D2 ./flash.sh jetson-agx-orin-devkit internal

nVidia:

$ sudo BOARDID="3701" FAB="300" BOARDSKU="0004" BOARDREV="C.2" CHIP_SKU=00:00:00:D2 ./flash.sh jetson-agx-orin-devkit internal

Board Layout

Front

<img _fck_mw_filename="Air030 board layout front.jpg" _fck_mw_origimgheight="718" _fck_mw_origimgwidth="2048" alt="Air030 board layout front.jpg" src="/wiki/images/5/59/Air030_board_layout_front.jpg" style="vertical-align:middle;" title="Air030 board layout front.jpg" width="400" />

Back

<img _fck_mw_filename="Air030 board layout back.jpg" _fck_mw_origimgheight="1044" _fck_mw_origimgwidth="2048" alt="Air030 board layout back.jpg" src="/wiki/images/c/cd/Air030_board_layout_back.jpg" style="vertical-align:middle;" title="Air030 board layout back.jpg" width="400" />

Bottom

<img _fck_mw_filename="Air030 board layout bottom.jpg" _fck_mw_origimgheight="2048" _fck_mw_origimgwidth="2048" alt="Air030 board layout bottom.jpg" src="/wiki/images/e/e0/Air030_board_layout_bottom.jpg" style="vertical-align:middle;" title="Air030 board layout bottom.jpg" width="400" />

Tools

JTOP

install

$ sudo apt update
$ sudo apt install python3-pip
$ sudo pip3 install -U jetson-stats

Run

$ sudo jtop

Test Command

GPIO Expander

<img _fck_mw_filename="Air030 dio.jpg" _fck_mw_origimgheight="1731" _fck_mw_origimgwidth="1537" alt="File:Air030_dio.jpg" src="/wiki/images/0/00/Air030_dio.jpg" style="vertical-align:middle;" title="File:Air030_dio.jpg" width="400" />

Test GPIO high/low
<img _fck_mw_filename="Air030 gpio expander io.png" _fck_mw_origimgheight="1532" _fck_mw_origimgwidth="1982" alt="Air030 gpio expander io.png" src="/wiki/images/6/6d/Air030_gpio_expander_io.png" style="vertical-align:middle;" title="Air030 gpio expander io.png" width="400" />
1).Switch to root

ubuntu@localhost:~ sudo -s

2).Commnad : where <GPIO> : GPIO0(GPIO300)~GPIO15(GPIO315) and <LEVEL> : high(1)/low(0)
For example, pull up GPIO0 to high.

root@localhost:/home/ubuntu# echo 300 > /sys/class/gpio/export
root@localhost:/home/ubuntu# echo out > /sys/class/gpio/gpio300/direction
root@localhost:/home/ubuntu# echo 1 > /sys/class/gpio/gpio300/value

WatchDog

root@linux:/home/ubuntu$ sudo -s
root@linux:/home/ubuntu# sync; sleep 2; sync; echo c > /proc/sysrq-trigger

RTC

DUT AC on:
1. Power on DUT and boot into OS.
2. Connect a LAN cable from the DUT to DHCP server.
3. Get a dynamic IP from DHCP server.
4. Type cmd to disable ntp service in DUT.

# sudo timedatectl set-ntp false

5. Synchronize system time and RTC time with NTP server.

# ntpdate tock.stdtime.gov.tw <===安裝ntpdate方式: $sudo apt-get install ntpdate <enter> 
# hwclock -w 

6. Keep the DUT on for 24 hours.
7. Synchronize system time and RTC time with NTP server again and check inaccuracies.

# ntpdate tock.stdtime.gov.tw && hwclock -s &&ntpdate -u tock.stdtime.gov.tw 

TPM

(1)產生randon code

root@linux:/home/ubuntu# tpm2_getrandom --hex 20

(2) 對指定檔案 msg.dat 加密

root@linux:/home/ubuntu# tpm2_createprimary -C p -c platform_primary.ctx
root@linux:/home/ubuntu# tpm2_create -C platform_primary.ctx -G rsa2048 -u key.pub -r key.priv
root@linux:/home/ubuntu# tpm2_load -C platform_primary.ctx -u key.pub -r key.priv -c key.ctx
root@linux:/home/ubuntu# echo "my test" >msg.dat
root@linux:/home/ubuntu# tpm2_rsaencrypt -c key.ctx -o msg.enc msg.dat
root@linux:/home/ubuntu# cat msg.enc
root@linux:/home/ubuntu# tpm2_rsadecrypt -c key.ctx -o msg.ptext msg.enc
root@linux:/home/ubuntu# cat msg.ptext 
root@linux:/home/ubuntu# cat msg.dat

(3) 將資料儲存至 tpm 內存

root@linux:/home/ubuntu# tpm2_nvdefine -Q 0x1500031 -C o -s 32 -a "ownerread|policywrite|ownerwrite"
root@linux:/home/ubuntu# echo "write_tpm_adv" >  adv.data
root@linux:/home/ubuntu# tpm2_nvwrite -Q 0x1500031 -C o -i adv.data
root@linux:/home/ubuntu# tpm2_nvread -Q 0x1500031 -C o -s 32 -o read.data
root@linux:/home/ubuntu# cat read.data

(4) 確認已經寫入儲存區域　

root@linux:/home/ubuntu# tpm2_nvreadpublic > nv.out
root@linux:/home/ubuntu# cat nv.out

Error

ERROR: Esys_NV_DefineSpace(0x14C) - tpm:error(2.0): NV Index or persistent object already defined
ERROR: Failed to create NV index 0x1500031.

fixed

root@linux:/home/ubuntu# tpm2_nvundefine 0x1500031

LAN

LAN1USB12 - eth01
LAN2USB34 - eth02
LAN3 - eth00

UART

<img _fck_mw_filename="COMPort.png" _fck_mw_origimgheight="403" _fck_mw_origimgwidth="341" alt="COMPort.png" src="/wiki/images/8/82/COMPort.png" style="vertical-align:middle;" title="COMPort.png" width="800" />
<img _fck_mw_filename="COMPortSwitchDefine.png" _fck_mw_origimgheight="399" _fck_mw_origimgwidth="1126" alt="COMPortSwitchDefine.png" src="/wiki/images/f/f0/COMPortSwitchDefine.png" style="vertical-align:middle;" title="COMPortSwitchDefine.png" width="800" />
RS232 (COMX_SW1 : OFF-OFF-X-X)

<img _fck_mw_filename="Air030 rs232loopback.jpg" _fck_mw_origimgheight="1615" _fck_mw_origimgwidth="1537" alt="File:Air030_rs232loopback.jpg" src="/wiki/images/e/e2/Air030_rs232loopback.jpg" style="vertical-align:middle;" title="File:Air030_rs232loopback.jpg" width="400" />

 UART5_SW1 - SW1 : ON

RS422
Send and Received port
(COM<PORT>_SW1 : ON-OFF-ON-OFF)

RS485
Send port
(COM<inPort>_SW1 ON-ON-ON-OFF)
Received port
(COM<outPort>_SW1 ON-ON-ON-ON)

Setup up baudrate

# stty -F /dev/ttyTHS<SEND_UART_NO> speed 115200
# stty -F /dev/ttyTHS<RECEIVE_UART_NO> speed 115200

Test

# cat /dev/ttyTHS<RECEIVE_UART_NO> &
# echo "1234" > /dev/ttyTHS<SEND_UART_NO>

Software control
(COM<inPort>_SWx ON-ON-OFF-ON)
AIR-030 RTS的GPIO號碼

UART1_RTS L51 GPIO3_PR.04 gpio-460 (PR.04)
UART2_RTS G58 GPIO3_PY.07 gpio-477 (PY.07)
UART4_RTS L4 GPIO3_PH.05 gpio-396 (PH.05)
UART5_RTS K58 GPIO3_PX.06 gpio-468 (PX.06)

舉起每個COM的RTS pin的方式如下(以UART1 RTS來說)

1.權限

ubuntu@localhost:~$ sudo –s

2.設定

root@localhost:/home/ubuntu# echo 460 > /sys/class/gpio/export
root@localhost:/home/ubuntu# ls /sys/class/gpio/
export gpiochip300 gpiochip316 gpiochip348 PR.04 unexport
root@localhost:/home/ubuntu# echo out > /sys/class/gpio/PR.04/direction
root@localhost:/home/ubuntu# echo 1 > /sys/class/gpio/PR.04/value

3.驗證

root@localhost:/home/ubuntu# cat /sys/kernel/debug/gpio | grep PR.04
gpio-460 (PR.04 |sysfs ) out hi

Audio

HDMI output

$ aplay -D hw:0,3 <WAV file>

Line-Out

$ aplay -D hw:1,0 <WAV file>

FAN

<img _fck_mw_filename="Air030 fan.jpg" _fck_mw_origimgheight="2048" _fck_mw_origimgwidth="1537" alt="File:Air030_fan.jpg" src="/wiki/images/4/42/Air030_fan.jpg" style="vertical-align:middle;" title="File:Air030_fan.jpg" width="400" />

Change PWM value ${PWM} from 1 ~ 255.

ubuntu@localhost:~$ sudo -s
For R35.1.0
root@localhost:/home/ubuntu# echo ${PWM} > /sys/class/hwmon/hwmon3/pwm1
For R35.3.1
root@localhost:/home/ubuntu# echo ${PWM} > /sys/class/hwmon/hwmon4/pwm1

Before test this item, please disable fan-control service.(Only for R35.1.0)

$ sudo systemctl disable nvfancontrol.service
$ sudo systemctl stop nvfancontrol

<a alt="https://docs.nvidia.com/jetson/archives/r35.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#fan-profile-control" href="https://docs.nvidia.com/jetson/archives/r35.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#fan-profile-control" title="https://docs.nvidia.com/jetson/archives/r35.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#fan-profile-control">nVidia:fan-profile-control</a>

CAN

<img _fck_mw_filename="Air030 can.jpg" _fck_mw_origimgheight="1808" _fck_mw_origimgwidth="1537" alt="File:Air030_can.jpg" src="/wiki/images/0/01/Air030_can.jpg" style="vertical-align:middle;" title="File:Air030_can.jpg" width="400" /> <img _fck_mw_filename="030CAN.png" _fck_mw_origimgheight="320" _fck_mw_origimgwidth="263" alt="030CAN.png" src="/wiki/images/4/40/030CAN.png" style="vertical-align:middle;" title="030CAN.png" width="200" />
<img _fck_mw_filename="CAN LoopbackTest.jpg" _fck_mw_origimgheight="800" _fck_mw_origimgwidth="600" alt="CAN LoopbackTest.png" src="/wiki/images/5/5d/CAN_LoopbackTest.jpg" style="vertical-align:middle;" title="CAN LoopbackTest.png" width="400" />

$ modprobe can
$ modprobe can-dev
$ modprobe mttcan
$ ip link set can0 type can bitrate 500000
$ ip link set can0 up
$ ip link set can1 type can bitrate 500000
$ ip link set can1 up

In other terminal, run below command

$ candump can1

then run

$ cansend can0 123#abcdabcd

USB

To test U-Disk read speed

$ sudo -s
# fio --ioengine=libaio --prio=0 --numjobs=1 --direct=1 --iodepth=32 --runtime=<runtime> --bwavgtime=5000 --time_based --rw=read --bs=128k --group_reporting --name=<device_path>

Where:
<runtime> : how long the test time (ms), ex : 30 second :  --runtime=30000
<device_path> : ex: --name=/dev/sda1

Camera

<img _fck_mw_filename="Air030 camera imx219.jpg" _fck_mw_origimgheight="1199" _fck_mw_origimgwidth="1498" alt="File:Air030_camera_imx219.jpg" src="/wiki/images/f/f6/Air030_camera_imx219.jpg" style="vertical-align:middle;" title="File:Air030_camera_imx219.jpg" width="400" />

The imx219 mode:
Size: Discrete 3280x2464 Interval: Discrete 0.048s (21.000 fps)
Size: Discrete 3280x1848 Interval: Discrete 0.036s (28.000 fps)
Size: Discrete 1920x1080 Interval: Discrete 0.033s (30.000 fps)
Size: Discrete 1640x1232 Interval: Discrete 0.033s (30.000 fps)
Size: Discrete 1280x720 Interval: Discrete 0.017s (60.000 fps)

Preview command:
3280x2464

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=3280, height=2464, format=NV12, framerate=21/1' ! nv3dsink

3280x1848

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=3280, height=1848, format=NV12, framerate=28/1' ! nv3dsink

1920x1080

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1920, height=1080, format=NV12, framerate=29/1' ! nv3dsink

1640x1232

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1640, height=1232, format=NV12, framerate=29/1' ! nv3dsink

1280x720

$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1280, height=720, format=NV12, framerate=59/1' ! nv3dsink

Capture Image (for JP6 : No nv3dsink gstreamer element, fixed by installing package nvidia-l4t-gstreamer)

$ nvargus_nvraw --c 0 --mode 0 --file /home/ubuntu/sample.jpg --format "yuv, jpg"

Power Mode

<a alt="https://docs.nvidia.com/jetson/archives/r34.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#supported-modes-and-power-efficiency" href="https://docs.nvidia.com/jetson/archives/r34.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#supported-modes-and-power-efficiency" title="https://docs.nvidia.com/jetson/archives/r34.1/DeveloperGuide/text/SD/PlatformPowerAndPerformance/JetsonOrinNxSeriesAndJetsonAgxOrinSeries.html#supported-modes-and-power-efficiency">Supported-modes-and-power-efficiency</a>

Flash Mac

<a alt="https://advantecho365-my.sharepoint.com/:u:/g/personal/jack501_chen_advantech_com/EczfhEigBcxIsAWt80o7iZkBH1EbUMTo7jQeX94DbJovsw?e=PPEyJU" href="https://advantecho365-my.sharepoint.com/:u:/g/personal/jack501_chen_advantech_com/EczfhEigBcxIsAWt80o7iZkBH1EbUMTo7jQeX94DbJovsw?e=PPEyJU" title="https://advantecho365-my.sharepoint.com/:u:/g/personal/jack501_chen_advantech_com/EczfhEigBcxIsAWt80o7iZkBH1EbUMTo7jQeX94DbJovsw?e=PPEyJU">I225 Flash Tool</a>
Copy and extract I225_Flash_Tool.zip in the device.

ubuntu@localhost:~$ unzip I225_Flash_Tool.zip

Chanage the tool execution permission.

<pre>ubuntu@localhost:~$ sudo chmod a+x ./EepromAccessTool

Check All Intel-226 Module in PCI bus, The BDF(bus number/device number/function number) value will be first column.

ubuntu@localhost:~$ lspci
0004:00:00.0 PCI bridge: NVIDIA Corporation Device 229c (rev a1)
0004:01:00.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:00.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:06.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:02:0e.0 PCI bridge: ASMedia Technology Inc. Device 2806 (rev 01)
0004:04:00.0 Ethernet controller: Intel Corporation Device 15f2 (rev 03)
0004:05:00.0 Ethernet controller: Intel Corporation Device 15f2 (rev 03)

Check NIC value with EepromAccessTool tool.

ubuntu@localhost:~$ ./EepromAccessTool
Intel(R) EEPROM Access Tool NVM/OTP Programming Example Tool   Version 0.8.0
Provided under the terms of a CNDA.  Do Not Distribute.
Copyright(C) 2017-2020 by Intel(R) Corporation
NIC     BUS     DEV     FUN     Silicon Memory Type Present
===     ===     ===     ===     =====   ======================
Check Command open to write error
 1      4        0       0      I225         FLASH
Check Command open to write error
 2      5        0       0      I225         FLASH

Flash Mac Address To get -nic value and BDF value please using above method.
ex : 0004:05:00.0 = domain 4 bus 5 device 0 function 0
BUS 5 > NIC = 2

$ sudo -s
# setpci -s 0004:04:00.0 COMMAND=0007
# ./EepromAccessTool -nic=1 -f=FXVL_15F2_LM_2MB_ARK_1.82_D.bin -mac=D4E5F6123456

The other Intel-I226

#setpci -s 0004:05:00.0 COMMAND=0007 
#./EepromAccessTool -nic=2 -f=FXVL_15F2_LM_2MB_ARK_1.82_D.bin -mac=D4E5F6123457 

Please do cold reboot after flash mac address.

How to check whether the flash proccess is success or not

• lspci command - If it is 0x125f value, it failed.
• ifconfig -a - Check the nerwork interface is available. ex: eth0, eth1 and so on.

Boot On Off

The boot count message will be printed before log-in.
<img _fck_mw_filename="Air030 bootcount.jpg" _fck_mw_origimgheight="104" _fck_mw_origimgwidth="488" alt="Air030 bootcount.jpg" src="/wiki/images/4/40/Air030_bootcount.jpg" style="vertical-align:middle;" title="Air030 bootcount.jpg" width="200" />
Reset the boot count please remove bootCount.tt.

$ rm bootCount.tt

THERMAL / EMI Burning

Install prerequisite packages

$ sudo apt install --yes nvidia-jetpack

pva engine

/opt/nvidia/vpi2/samples/05-benchmark/vpi_sample_05_benchmark

GPU
matrixMul (Depreciated)

/usr/local/cuda-11.4/samples/0_Simple/matrixMul/

More power consumption version (nVidia suggestion + <a href=":File%3AAir030-half-matrixMulCUBLAS.patch">0001-half-matrixMulCUBLAS.patch</a>)
matrixMulCUBLAS

/usr/local/cuda-11.4/samples/0_Simple/matrixMulCUBLAS/

emc  engine

sudo apt install mbw

cpu

sudo apt install stress

dla0 dla1  engine

/usr/src/tensorrt/bin/trtexec

nvenc engine - USB camera

$ gst-launch-1.0  v4l2src device=/dev/video0 ! 'video/x-raw,width=1280,height=720' ! nvvidconv ! 'video/x-raw(memory:NVMM)' ! nvvidconv ! 'video/x-raw(memory:NVMM)' ! nvv4l2h264enc ! fakesink

nvdec engine - play 4K H264 video

gst-launch-1.0 filesrc location=/usr/local/bin/4k264.mp4 ! qtdemux ! queue ! h264parse ! nvv4l2decoder ! 'video/x-raw(memory:NVMM), format=(string)NV12' ! queue ! fakesink

ape  engine

aplay -D hw:1,0 /usr/local/bin/1kHz.wav

Module

AW-CB375NF(EWM-W159M201E)

<img _fck_mw_filename="Air030 awcb375nf.jpg" _fck_mw_origimgheight="1658" _fck_mw_origimgwidth="1302" alt="File:Air030_awcb375nf.jpg" src="/wiki/images/1/12/Air030_awcb375nf.jpg" style="vertical-align:middle;" title="File:Air030_awcb375nf.jpg" width="400" /> <img _fck_mw_filename="Air030 awcb375nf onboard.jpg" _fck_mw_origimgheight="2048" _fck_mw_origimgwidth="1537" alt="File:Air030_awcb375nf_onboard.jpg" src="/wiki/images/1/11/Air030_awcb375nf_onboard.jpg" style="vertical-align:middle;" title="File:Air030_awcb375nf_onboard.jpg" width="400" />

Adjust dip switch

• LAN3_MKE_SW1 - SW1 : ON
• UART5_SW1 - SW1 : OFF

<img _fck_mw_filename="AIR030 LAN3 MKE SW1.jpg" _fck_mw_origimgheight="916" _fck_mw_origimgwidth="1632" alt="AIR030_LAN3_MKE_SW1.jpg" src="/wiki/images/5/5c/AIR030_LAN3_MKE_SW1.jpg" style="vertical-align:middle;" title="AIR030_LAN3_MKE_SW1.jpg" width="400" /> <img _fck_mw_filename="Air030 uart5 selection.jpg" _fck_mw_origimgheight="936" _fck_mw_origimgwidth="1756" alt="Air030_uart5_selection.jpg" src="/wiki/images/6/67/Air030_uart5_selection.jpg" style="vertical-align:middle;" title="Air030_uart5_selection.jpg" width="400" />

Wi-Fi
Start interface

$ sudo ifconfig wlan0 up

$ Scan AP

$ sudo iw dev wlan0 scan ap-force

Bluetooth

$ bluetoothctl
[bluetooth]# agent on
[bluetooth]# scan on

AW-CB511NF

Adjust dip switch

• LAN3_MKE_SW1 - SW1 : ON
• UART5_SW2 - SW1 : OFF

Wi-Fi
Start interface

$ sudo ifconfig wlan0 up

$ Scan AP

$ sudo iw dev wlan0 scan ap-force

Bluetooth

$ sudo -s
# hciattach /dev/ttyTHS1 bcm43xx 3000000 flow -t 20
# bluetoothctl
[bluetooth]# agent on
[bluetooth]# scan on

AIW-35x

<img _fck_mw_filename="Air030 aiw-356.jpg" _fck_mw_origimgheight="935" _fck_mw_origimgwidth="1529" alt="File:Air030_aiw-356.jpg" src="/wiki/images/b/b2/Air030_aiw-356.jpg" style="vertical-align:middle;" title="File:Air030_aiw-356.jpg" width="400" /> <img _fck_mw_filename="Air030 aiw-356 onboard.jpg" _fck_mw_origimgheight="2048" _fck_mw_origimgwidth="1537" alt="File:Air030_aiw-356_onboard.jpg" src="/wiki/images/7/73/Air030_aiw-356_onboard.jpg" style="vertical-align:middle;" title="File:Air030_aiw-356_onboard.jpg" width="400" /> <img _fck_mw_filename="Air030 uart5 selection.jpg" _fck_mw_origimgheight="936" _fck_mw_origimgwidth="1756" alt="Air030_uart5_selection.jpg" src="/wiki/images/6/67/Air030_uart5_selection.jpg" style="vertical-align:middle;" title="Air030_uart5_selection.jpg" width="400" />

Check the module is available.

ubuntu@localhost:~$ lsusb
Bus 002 Device 002: ID 05e3:0625 Genesys Logic, Inc. USB3.2 Hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 006: ID 2cb7:0104

buntu@localhost:~$ ifconfig usb0
        usb0: flags=4227<UP,BROADCAST,NOARP,MULTICAST> mtu 1500
        ether 00:33:34:37:35:33  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ubuntu@localhost:~$ sudo dmesg | grep usb0 
[ 14.115707] GobiNet 1-3.4:1.4 usb0: register 'GobiNet' at usb-3610000.xhci-3.4, GobiNet Ethernet Device, d2:77:82:0c:af:59

Switch mode:

$ sudo minicom -D /dev/ttyUSBx

ATcommand : at+gtusbmode=32
30 : mbim
32 : rmnet(gobinet)

NVME

<img _fck_mw_filename="Air030 nvme.jpg" _fck_mw_origimgheight="498" _fck_mw_origimgwidth="1610" alt="File:Air030_nvme.jpg" src="/wiki/images/a/ab/Air030_nvme.jpg" style="vertical-align:middle;" title="File:Air030_nvme.jpg" width="400" /> <img _fck_mw_filename="Air030 nvme onboard.jpg" _fck_mw_origimgheight="2048" _fck_mw_origimgwidth="1537" alt="File:Air030_nvme_onboard.jpg" src="/wiki/images/2/2f/Air030_nvme_onboard.jpg" style="vertical-align:middle;" title="File:Air030_nvme_onboard.jpg" width="400" />

PCIE-1672

<img _fck_mw_filename="Air030 pcie1672v.jpg" _fck_mw_origimgheight="1117" _fck_mw_origimgwidth="2048" alt="File:Air030_pcie1672v.jpg" src="/wiki/images/e/ee/Air030_pcie1672v.jpg" style="vertical-align:middle;" title="File:Air030_pcie1672v.jpg" width="400" />

Image

The test image is available <a alt="https://advantecho365-my.sharepoint.com/personal/jack501_chen_advantech_com/_layouts/15/onedrive.aspx?ga=1&id=/personal/jack501_chen_advantech_com/Documents/AIR-030/image" href="https://advantecho365-my.sharepoint.com/personal/jack501_chen_advantech_com/_layouts/15/onedrive.aspx?ga=1&id=/personal/jack501_chen_advantech_com/Documents/AIR-030/image" title="https://advantecho365-my.sharepoint.com/personal/jack501_chen_advantech_com/_layouts/15/onedrive.aspx?ga=1&id=/personal/jack501_chen_advantech_com/Documents/AIR-030/image">HERE</a>. The 1st and 2nd image is only available for AGX-ORIN devkit.

Pages with broken file links