Difference between revisions of "Wise32xxweb/LuCI"
Line 132: | Line 132: | ||
=== Ethernet === | === Ethernet === | ||
+ | |||
+ | In this sector we suggest only editing ethernet wan interface instead of lan interface. | ||
Setting Ethernet IP address. | Setting Ethernet IP address. | ||
− | *Select interface. | + | *Select Wan interface. |
[[File:3240ethernet.jpg|600px|3240ethernet.jpg]] | [[File:3240ethernet.jpg|600px|3240ethernet.jpg]] | ||
+ | |||
+ | *select protocol | ||
[[File:3240ethernet 1.jpg|600px|3240ethernet 1.jpg]] | [[File:3240ethernet 1.jpg|600px|3240ethernet 1.jpg]] | ||
− | * | + | *Click switch protocol. |
[[File:3240ethernet 2.jpg|600px|3240ethernet 2.jpg]] | [[File:3240ethernet 2.jpg|600px|3240ethernet 2.jpg]] | ||
− | * | + | *Input IPv4 IP address & netmask. |
[[File:3240ethernet 3.jpg|600px|3240ethernet 3.jpg]] | [[File:3240ethernet 3.jpg|600px|3240ethernet 3.jpg]] | ||
− | |||
− | |||
=== Wifi === | === Wifi === |
Revision as of 03:51, 10 April 2019
Contents
Default Setting
- IP Address: 192.168.1.1
- Username: root
- Password: ePaper
Main Page / System Information
If logging successful, you will see software information on the Overview page as following.
Status
Firewall
This page show firewall rule table. When you change the firewall setting of Ethernet interface , you should click Restart Firewall
System log
This page show about system log message
kernel log
This page show about linux Kernel message
Processes
This page shows all running processes on your system, with child processes indented and displayed below their parent. For each process the PID, owner and command are displayed. You can terminate the running processes but you should know the risk of the service stop in system.
System
System
This page offer three function operation as below
- System Properties
This function is for sync the system's current time with browser .On operating systems that have a separate hardware clock, it can be used to set that too. This form also offer User-defined host name.
- Change time zone
It also allows you to set the system's default time zone, which is used to convert the system time to a human-readable format and offset.
- Time server sync
This function is for configuring the system to automatically synchronize the time with a remote server. Synchronization will be done using the Unix time protocol or NTP, depending on which commands are installed and what the remote system supports.
Administration Users
This page you can change LuCI web login password as you want
Backup/Flash Firmware
This page has four operation Download backup、Restore backup 、Reset to defaults and flash firmware as below.
Download backup & Restore backup
User can download backup file that is value of all web settings by click on "Generate archive" button.
When user has been downloaded backup file, user can recover all web settings by function of restore backup.
Reset to defaults
Click "Perform reset" button the value of all the web settings will be back to original setting.
Firmware Update
Please download the most updated Firmware version from Advantech Website to your computer.
1.Click choose file button and upload the image.
2.Click "Flash image" button and upload firmware image
3. After firmware image upload complete, it show the Checksum on screen.
User should make sure the firmware checksum is correct or not and click button proceed.
- Please note
1. Firmware update process may take around 1~2 minutes, please don’t turn off the power or press the reset button.
2. After firmware upgrade, the system will restore its default setting, the IP address will return to 192.168.1.1.
3. The device is unavailable during the upgrade process. Any connections to or through the device will be lost.
Reboot
User can reboot system through clcik "Perform reboot". System will reboot immediately.
Service
Remote Management
In this Page, you can manage the router from anywhere on the Internet port.
Network Configuration
In this page, you can set Network Interface, Routing Gateways and DNS Client based on your networking environment.
Ethernet
In this sector we suggest only editing ethernet wan interface instead of lan interface.
Setting Ethernet IP address.
- Select Wan interface.
- select protocol
- Click switch protocol.
- Input IPv4 IP address & netmask.
Wifi
In this page, you can set wireless Interface, scan other wifi router in your environment or setting wifi AP mode. Default setting wifi Ap mode, The access point account: wise_3240 and no password
- Edit wifi AP mode
User can change Wifi Ap SSID and Password yourself.
1. Click Edit button
2. Change SSID and Password yourself
The password need select Encryption and string length must be more than 8.
- Establish Wi-Fi Sta <-> Wi-Fi AP mode setting.
This mode is means wise-3240 wireless uplink through another Wifi Ap router to internet and downlink offer the Wifi client access point.
The configure method step by step as following.
1. Scan other Wifi Ap router in user's network environment.
2. Join network as your network environment
Input password which you choice wifi connection and Click submit.
3. Screen shows wifi client mode setting page. Click save & apply immediately.
4. User can check the connection SSID and RSSI percentage. After check SSID and RSSI , Click Disable button to stop wifi function.
5. we set up wifi station mode for uplink as above step and next step is setting Wifi Ap mode for downlink.
Click add button.
User should input SSID 、Password as you need.
The password need select Encryption and string length must be more than 8.
6. Enable wifi station connection and User can check wifi mode client and Master on screen.