Revision as of 05:22, 26 September 2022

Getting Started

Conventions

${PREBUILT_IMAGE} : compressed prebuilt image (*.img.gz)

${CONTAINER_NAME} : container name (e.g. imx8LBVB0016)

${BSP_TARBALL} : BSP tarball (*.tgz)

${BSP_HOME} : home directory of the BSP

${BDIR} : build directory (e.g. build_x11)

${MX8PROC} : i.MX8 Processor

mx8mq for iMX8M Dual Core

mx8mm for iMX8MM

mx8mp for iMX8MP

mx8qm for iMX8QM

mx8qxp for iMX8QXP

${IMX8PROC} : i.MX8 Processor

imx8mq / imx8mm / imx8qm /imx8qxp /imx8mp

${BOARD} : available target boards list below

rom5720

rom5721

rom7720

rom5620

rom3620

rom5722

rsb3720

${BOARD_REV} : board revision

a1

${MC} : machine code combined with ${IMX8PROC}${BOARD}${BOARD_REV}

for example,

imx8mqrom5720a1 for ROM-5720 A1

imx8qmrom7720a1 for ROM-7720 A1

imx8qxprom5620a1 for ROM-5620 A1

imx8qxprom3620a1 for ROM-3620 A1

imx8mmrom5721a1 for ROM-5721 A1

imx8mprom5722a1 for ROM-5722 A1

imx8mprsb3720a1 for RSB-3720 A1

You can also use the command below to check supported machines on BSP

$ source setup-environment

${MEM_SIZE} : memory size

2G/4G

${UC} : u-boot config

1G/2G/4G/FSPI_1G/FSPI_2G...

${SD_DEVICE} : device name of SD card in Linux (e.g. /dev/sdf)

${SDCARD_IMAGE} : sdcard image built by bitbake (*.wic.bz2)

${WORKSPACE} : host workspace folders

${UBOOT} :u-boot version(e.g. 2016.03)

${KERNEL} : linux kernel version(e.g. 4.14.98)

${TOOLCHAIN} : toolchain installed directory(e.g. /opt/fsl-imx-x11/4.1.15-2.0.0)

debug console / serial console

serial terminal program (e.g. minicom, putty, teraterm ...) that serial port is configured to 115200 8N1

terminal console

terminal program (e.g. gnome-terminal, xfce4-terminal ...)

Docker install and setting

If you don't have docker in your system, then you can follow the below steps to install docker and run it first.

To install Docker Engine on your platform

Please refer to Docker Installation Guide for details

To pull ubuntu 18.04 image from Docker Hub

$ docker pull advrisc/u18.04-imx8lbv1

To create container

$ docker run --privileged -it --name ${CONTAINER_NAME} -v ${WORKSPACE}:/home/adv/adv-release-bsp -v /dev:/dev advrisc/u18.04-imx8lbv1 /bin/bash

Get BSP

You have two methods to put BSP into container created above

Download_BSP_From_GitHub

The following example shows how to download the Advantech Yocto BSP from GitHub.

For this example, a directory called adv-release-bsp is created for the project.

Refer to IoTGateway/BSP/Linux/iMX8/OS_Support_List , Official version "imx8LBVB0209" is taken as an example :

$ git config --global user.name "Your Name"
$ git config --global user.email you@example.com
$ sudo chown adv:adv adv-release-bsp
$ cd adv-release-bsp
$ repo init -u git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git -b refs/tags/imx8LBVB0209 -m imx8LBVB0209.xml 
$ repo sync

If you want to get latest bsp

$ repo init -u git://github.com/ADVANTECH-Corp/adv-arm-yocto-bsp.git  -b imx-linux-hardknott -m imx-5.10.35-2.0.0.xml 
$ repo sync

If you suffer "server certificate verification failed", you can use the following command to disable SSL verification in git repositories with self-signed certificates.

$ export GIT_SSL_NO_VERIFY=1

or

$ git config --global http.sslverify false

If you get "The unauthenticated git protocol on port 9418 is no longer supported.", you can try it.

$ git config --global url."https://".insteadOf git://

Copy BSP tarball to Container

If you have BSP tarball (eg. imx8LBVB0029_2019-10-23.tgz), then you have to copy it into container.

Follow the steps below:

1.Exit container and back to local machine

$ exit

2.Copy BSP tarball to ${WORKSPACE} , and change owner

$ cp imx8LBVB0029_2021-10-23.tgz ${WORKSPACE}
$ sudo chown adv:adv ${WORKSPACE}/imx8LBVB0029_2021-10-23.tgz

3.Back to container

$ docker start ${CONTAINER_NAME}
$ docker attach ${CONTAINER_NAME}

4.Unpack BSP tarball

$ tar zxvf imx8LBVB0029_2021-10-23.tgz

Downloads tarball

Not necessarily step

During building Yocto image , it will generate downloads folder which includes all packages we need , but it usually can't fetch normally, so we keep this downloads folder. Then we can reduce some fetch failed issue.

You can get Downloads tarball (downloads_imx8_5.10.35.tar.gz) from following URL:

[downloads_imx8_5.10.35.tar.gz], md5 checksum: 912999faf861bf413cef4cf7a9f18dfa

If you get downloads tarball, you can copy to your ${WORKSPACE}

Follow the steps below:

1.Exit container and back to local machine

$ exit

2.Copy Downloads tarball to ${WORKSPACE} , and change owner

$ cp downloads_imx8_5.10.35.tar.gz ${WORKSPACE}
$ sudo chown adv:adv ${WORKSPACE}/downloads_imx8_5.10.35.tar.gz

3.Back to container

$ docker start ${CONTAINER_NAME}
$ docker attach ${CONTAINER_NAME}

4.Unpack Downloads tarball

$ tar zxvf downloads_imx8_5.10.35.tar.gz

5.make link to downloads folder

$ cd adv-release-bsp
$ ln -s ${WORKSPACE}/downloads_imx8_5.10.35 downloads

Introducing BSP

The BSP is based on Yocto Project with Freescale enhanced features for i.MX8, plus specific target board features from Advantech Inc..

The Advantech Yocto Project BSP Release directory contains a "sources" directory, which contains the recipes used to build,

one or more build directories, and a set of scripts used to set up the environment.

The recipes used to build the project come from both the community and Advantech. The Yocto Project layers are downloaded

to the sources directory. This sets up the recipes that are used to build the project.

Naming Rule

The tarball/prebuilt image name is consist of the model name followed by "LB" or "LI" plus version number and released date.

For example, BSP file name: imx8LBVA0010_2019-08-27.tgz

which , "LB" is acronym of Linux BSP,

"VA0010" stands for Version A.0010 .

For example, Yocto image name: '5720A1AIM20LIVA0010_iMX8M_2G_2020-08-27.img.gz'

which "5720A1" stands for ROM-5720 A1

"LI" is acronym for prebuilt Linux Image

"2G" is DDR size

BSP Content

The description of some important folders list below:

sources/

meta-advantech/ : meta layer by Advantech

meta-fsl-*/ : meta layer by Freescale

fsl-setup-release.sh : to create one new build environment

setup-environment : to continue an exist build environment

Build Instructions

To create one new build environment

Perform the following commands in terminal console

$ cd ${BSP_HOME}

$ MACHINE=${MC} DISTRO=fsl-imx-xwayland source imx-setup-release.sh -b ${BDIR}

We can specify u-boot default config like below

$ MACHINE=${MC} UBOOT_CONFIG=${UC} DISTRO=fsl-imx-xwayland source imx-setup-release.sh -b ${BDIR}

You need to read and accept the EULA.

To continue an exist build environment

Perform the following commands in terminal console

$ cd ${BSP_HOME}

$ source setup-environment ${BDIR}

To build sdcard image

To create/continue a build environment

Perform the following command in terminal console

$ bitbake imx-image-full

The file, imx-image-full-${MC}.sdcard.bz2, will be located in directory, ./tmp/deploy/images/${MC}, while building process finished successfully.

To build toolchain installer

To create/continue a build environment

Perform the following command in terminal console

$ bitbake meta-toolchain

The below installer will be located in the directory "./tmp/deploy/sdk".

fsl-imx-xwayland-glibc-x86_64-meta-toolchain-aarch64-toolchain-${KERNEL}-zeus.sh

To build bootloader

To create/continue a build environment

Perform the following command in terminal console

$ bitbake imx-boot

To build linux kernel

To create/continue a build environment

If you operate on docker images, please install tmux application before running this command

$ sudo apt-get install tmux

Type following command to enter tmux

$ tmux

Perform the following command in terminal console to show up menuconfig

$ bitbake linux-imx -c menuconfig

After edit menuconfig, type following command to exit tmux windows

$ exit

to build kernel image

$ bitbake linux-imx

The two files, Image & Image-${IMX8PROC}-${BOARD}-${BOARD_REV}.dtb, will be located in the directory, ./tmp/deploy/images/${MC}.

Creating boot-up on-board flash from prebuilt image

To create one boot-up SD card

Perform the following command in terminal console

# gunzip -c ${PREBUILT_IMAGE} | dd of=${SD_DEVICE} bs=1M

# sync

Creating boot-up on-board flash from built sdcard image

To create one boot-up SD card

Perform the following commands in terminal console

$ pushd ${BSP_HOME}/${BDIR}/tmp/deploy/images/${MC}

$ sudo bzcat ${SDCARD_IMAGE} | sudo dd of=${SD_DEVICE} bs=1M

$ sync

$ popd

Debug console information

If you want to see debug message from device, you need to prepare for hardware device and software tool.

Preparing for hardware device

The following URL provides information about the debug port slot and the debug port line for each device

Debug Port Information

Preparing for software tool

You need to prepare the debug console tool. For example: "minicom" tool or "putty" tool.
Baud rate: 115200

One step build image

Our machine must be pre-installed docker

Download the following script can quickly build our image.

$ wget https://raw.githubusercontent.com/ADVANTECH-Corp/RISC_tools_scripts/hardknott/imx8/adv_imx8_build.sh
$ sudo chmod a+x adv_imx8_build.sh

Build image

$ sudo ./adv_imx8_build.sh ${BOARD}
$ sudo ./adv_imx8_build.sh rom5720

Our image will be in workspace folder.

workspace/${BDIR}/tmp/deploy/images/${MC}

Then refer to Creating_boot-up_on-board_flash_from_built_sdcard_image to build SD card.

Customization

Package addition

To add tcf-agent & openssh-sftp-server

Navigate to the directory where fsl-image-adv.inc located

$ cd ${BSP_HOME}/sources/meta-advantech/meta-fsl-imx/recipes-fsl/images

Add following line to fsl-image-adv.inc

IMAGE_INSTALL += " tcf-agent openssh-sftp-server "

Continue an exist build environment and build sdcard image

To add chromium browser

Navigate to the directory where local.conf located

$ cd ${BSP_HOME}/${BDIR}/conf

Method 1(Suggest): Add following one line to local.conf

CORE_IMAGE_EXTRA_INSTALL += "chromium-ozone-wayland"

Method 2: Add following two lines to local.conf

IMAGE_INSTALL_append = \
   "${@bb.utils.contains('DISTRO_FEATURES', 'wayland', ' chromium-ozone-wayland libexif', \
       bb.utils.contains('DISTRO_FEATURES',     'x11', ' chromium-x11 libexif', \
                                                        , d), d)}"
LICENSE_FLAGS_WHITELIST = \
   "${@bb.utils.contains('DISTRO_FEATURES', 'wayland', 'commercial', \
       bb.utils.contains('DISTRO_FEATURES',     'x11', 'commercial', \
                                                       , d),"

Continue an exist build environment and build sdcard image

To add QtWebEngine

Put the following in ${BSP_HOME}/${BDIR}/conf/local.conf

IMAGE_INSTALL_append += "packagegroup-qt5-webengine"

Continue an exist build environment and build sdcard image

Setting up SDK

Please follow the section,To build toolchain installer, to build one toolchain installer

Perform the following command in terminal console

$ cd ${BSP_HOME}/${BDIR}/tmp/deploy/sdk

$ sudo ./fsl-imx-xwayland-glibc-x86_64-meta-toolchain-aarch64-toolchain-5.4-zeus.sh

Enter new installed directory or just press Enter to use default directory.

While Proceed[y/n]? shows up, please enter the correct one.

Waiting for the SDK installed (while the following messages show up completely)

Setting up cross compiling environment

SDK has been set up (ref.Setting up SDK)

Perform the following command in terminal console

$ source ${TOOLCHAIN}/environment-setup-aarch64-poky-linux

Build U-Boot in standalone environment

Config u-boot

make ${IMX8PROC}_${BOARD}${BOARD_REV}_${MEM_SIZE}_defconfig

eg.

make imx8mm_rom5721a1_2G_defconfig

Build u-boot

make -j4

Build imx-boot image by using imx-mkimage

Get imx-boot tarball from our server Here we take rom5721 as an example:

tar zxvf 5721A1AIM20LIVA0118_iMX8MM_imx-boot.tgz 
cd 5721A1AIM20LIVA0118_iMX8MM_imx-boot/

In this folder , we have two script as below: Copy necessary files to imx-mkimage folder

./cp_uboot.sh ${uboot path} ${IMX8PROC}

Make imx-boot image

./mk_imx-boot.sh ${IMX8PROC}

eg.

./cp_uboot.sh ../uboot-imx6 imx8m
./mk_imx-boot.sh imx8mm

Replace imx-boot

Perform the following command to transfer to on-board flash

$ dd if=flash.bin of=/dev/mmcblk0 bs=1K seek=<offset> conv=fsync

Where offset is:

33 - for i.MAX 8QuadMax A0, i.Mx 8QuadXPlus A0, i.MX 8M Quad, and i.MX 8M Mini

32 - for iMX 8M PLUS, i.MAX 8QuadXPlus B0/C0 and i.Mx 8QuadMax B0

Building & updating kernel/modules/dtb manually

The cross compiling environment has been set up. (ref. Setting up cross compiling environment)

Copy BSP tarball to Container

Refer to Copy_BSP_tarball_to_Container , copy kernel tarball to ${WORKSPACE} and back to container

change owner & unpack tarball

$ sudo chown adv:adv imx8LBVA0029_2019-10-23_linux-imx.tgz
$ tar zxvf imx8LBVA0029_2019-10-23_linux-imx.tgz

Config kernel

Configure linux kernel

$ cd linux-imx
$ make distclean
$ make imx_v8_adv_defconfig
$ make menuconfig

Start building linux kernel

$ make -j4 Image

When you get error like below

run command then rebuild

$ unset LDFLAGS

The kernel image file, Image, is located in the directory "./arch/arm64/boot/".

Start building kernel modules

$ make -j4 modules

Copy all modules to a temporary rootfs directory, "~/temp/rootfs"

$ make modules_install INSTALL_MOD_PATH=~/temp/rootfs

Building device tree blob

$ make -j4 freescale/${IMX8PROC}-${BOARD}-${BOARD_REV}.dtb
eg.
$ make -j4 freescale/imx8mq-rom5720-a1.dtb

The device tree blob, ${IMX8PROC}-${BOARD}-${BOARD_REV}.dtb, is located in the directory "./arch/arm64/boot/dts/freescale/".

Replace kernel & dts

Replace kernel

copy Image to SDcard or emmc

Replace dtb file

copy dtb file to SDcard or emmc

Improve boot speed

Bootloader

1.bootdelay time

We can cancel the bootdelay time by setting bootloader environment value.

setenv bootdelay 0
env save
reset

2.Disable console

Disable debug message output can also improve boot speed

Disable kernel message

setenv mmcargs setenv bootargs ${jh_clk} console=${console} modprobe.blacklist=${modprobe.blacklist} root=${mmcroot} video=HDMI-A-1:${videores} quiet
env save
reset

Or

Disable debug port

setenv console
env save
reset

Rootfs

TBD

Services

1. Using systemctl disable remove ,we can remove unnecessary services.

systemctl disable <services>

eg.

systemctl disable boottimes

System Recovery

This section provides detail procedures of restoring the eMMC image.

If you destroy the onboard flash image by accident, you can recover a system following these steps.

Recovery by SD card

1.Copy 5720A1AIM20LIVA0022_iMX8M_flash_tool.tgz package to your desktop.

2.Insert SD card to PC

3.Make a bootable sd card

# tar zxvf 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool.tgz
# cd 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/sdg

4.Insert SD card and copy 5720A1AIM20LIVA0022_iMX8M_flash_tool to USB disk

5.Insert USB disk and SD card then Boot from SD

6.Enter usb disk folder, make a bootable emmc

# cd /run/media/sda1/
# cd 5720A1AIM20LIVA0022_iMX8M_2G_flash_tool/mk_inand/
# sudo ./mksd-linux.sh /dev/mmcblk0

Recovery by UUU tool

1.Download uuu tool from (https://github.com/ADVANTECH-Corp/uuu/releases/tag/v20200619)

2.burn command

For Linux

 sudo ./uuu

For Windows

 uuu.exe

2.Create a folder with files as below:

1.uuu
2.imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
3.fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard
4.Image_dtb.uuu
5.rootfs.uuu

3.Connect otg cable from PC to device

4.Set the correct boot mode(ROM5720/ROM5721/ROM5620: 1,2,3-off 4-on, ROM7720: 1,2,3,4,5,6-off or 1,2,4,5,6-off 3-on), then power on

5.Perform the following command:

PS.If you want to burn uboot to mmcblk0 instead of mmcblk0boot0, u-boot must be updated to version 20191101,

1.Burn uboot to emmc
   a)replace uboot in mmcblk0boot0
       sudo ./uuu -b emmc imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
   b)replace uboot in mmcblk0
       sudo ./uuu -b emmc_adv imx-boot-imx8mqrom5720a1-sd.bin-flash_evk
2.Burn rootfs image to emmc
   a)replace uboot in mmcblk0boot0
       sudo ./uuu -b emmc_all imx-boot-imx8mqrom5720a1-sd.bin-flash_evk fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard
   b)replace uboot in mmcblk0
       sudo ./uuu -b emmc_all_adv imx-boot-imx8mqrom5720a1-sd.bin-flash_evk fsl-image-validation-imx-imx8mqrom5720a1-20190917152605.rootfs.sdcard

6.uuu tool will start recovery image to emmc.

7.If we want to burn separately into emmc

   a)replace Image and dtb
       Step 1: rename Image and dtb 
                 _Image
                 _board.dtb
       Step 2: 
                 sudo ./uuu Image_dtb.uuu
   b)replace rootfs
       Step 1: rename rootfs tarball
                 _rootfs.tar.bz2
       Step 2: 
                 sudo ./uuu rootfs.uuu

8.Another method for update Kernel and DTB by UUU

    # The version of UUU must be '''1.4.139''' up
    # On U-boot enter fastboot mode
        u-boot > fastboot 0
    # Download Kernel and DTB using UUU
        sudo uuu -b fat_write Image mmc 0:1
        sudo uuu -b fat_write xxx.dtb mmc 0:1

9.For more usage (https://github.com/NXPmicro/mfgtools/wiki)

Package List

In BSP, list all packages which will be built in the image

bitbake -g fsl-image-qt5-validation-imx && cat recipe-depends.dot | grep -v -e '-native' | grep -v digraph | grep -v -e '-image' | awk '{print $1}' | sort | uniq

20191025 Package List

Show all recipes (include non-installed packages)

bitbake -s

20191025 Package Version List

You can also check ${BDIR}/tmp/deploy/images/${MC}/fsl-image-qt5-validation-imx-${MC}.manifest

It will show the same content with checking by rpm tool on target board.

On target board, list all packages by rpm tool

rpm -qa --root / --dbpath /var/lib/rpm | sort

20191025 RPM on Board List

Device Tree Source file select

We can setup different dts file on bootloader to enable different devices.

eg.

setenv fdt_file adv-imx8mm-rom5721-a1-dsi2dp.dtb
env save
boot

ROM-5721

Display
- DSI to LVDS
  - g070vw01
    - imx8mm-rom5721-a1.dtb
  - g150xgel05
    - imx8mm-rom5721-a1-dsi2lvds-g150xgel05.dtb
  - g215hvn01
    - imx8mm-rom5721-a1-dsi2lvds-g215hvn01.dtb
- DSI to DP
  - imx8mm-rom5721-a1-dsi2dp.dtb
- DSI to HDMI
  - imx8mm-rom5721-a1-adv7535.dtb
- DSI
  - auog101uan02
    - imx8mm-rom5721-a1-auog101uan02.dtb
M.2 SDIO
- Adjust CN43~CN48
- imx8mm-rom5721-a1-m2-sdio.dtb

ROM-5720

Display
- DSI to HDMI
  - imx8mq-rom5720-a1-dcss-adv7535.dtb
  - imx8mq-rom5720-a1-lcdif-adv7535.dtb
  - For weston ui
    - modify /etc/xdg/weston/weston.ini
      - drm-device=card2
- DSI
  - auog101uan02
    - imx8mq-rom5720-a1-dcss-auog101uan02.dtb
- Dual Display
  - DSI to HDMI + HDMI
    - imx8mq-rom5720-a1-dual-display.dtb
    - For weston ui
      - modify /etc/xdg/weston/weston.ini
        drm-device=card1
M.2 SDIO
- Adjust CN43~CN48
- imx8mq-rom5720-a1-m2-sdio.dtb

ROM-5620

Display
- LVDS
  - g070vw01
    - imx8mxp-rom5620-a1.dtb
  - g150xgel05
    - imx8qxp-rom5620-a1-lvds-chimei.dtb
  - g215hvn01
    - imx8qxp-rom5620-a1-lvds-dual.dtb
- LVDS to HDMI
  - imx8qxp-rom5620-a1-hdmi-bridge.dtb
- DSI to HDMI
  - imx8qxp-rom5620-a1-hdmi-bridge.dtb
- DSI
  - auog101uan02
    - imx8qxp-rom5620-a1-auog101uan02.dtb
M.2 SDIO
- Adjust CN43~CN48
- imx8qxp-rom5620-a1-m2-sdio.dtb

ROM-7720

Display
- HDMI
  - imx8qm-rom7720-a1.dtb
- LVDS
  - g070vw01
    - imx8qm-rom7720-a1-lvds0.dtb
    - imx8qm-rom7720-a1-lvds1.dtb
  - g215hvn01
    - imx8qm-rom7720-a1-lvds-dual.dtb
- HDMI + LVDS
  - HDMI + g070vw01
    - imx8qm-rom7720-a1-hdmi-lvds0.dtb
    - imx8qm-rom7720-a1-hdmi-lvds1.dtb
  - HDMI + g215hvn01
    - imx8qm-rom7720-a1-hdmi-lvds-dual.dtb
- LVDS to HDMI
  - imx8qm-rom7720-a1-it6263.dtb
Audio Codec
- imx8qm-rom7720-a1-sgtl5000.dtb

RSB-3720

Display
- HDMI (default)
  - imx8mp-rsb3720-a1.dtb
- LVDS
  - g070vw01(LVDS0) + HDMI
    - imx8mp-rsb3720-a1-lvds0-auo.dtb
  - g070vw01(LVDS1) + HDMI
    - imx8mp-rsb3720-a1-lvds1-auo.dtb
  - g215hvn01(DUAL LVDS) + HDMI
    - imx8mp-rsb3720-a1-lvds-dual.dtb
- DSI
  - adv7535(DSI to HDMI) + HDMI
    - imx8mp-rsb3720-a1-adv7535.dtb
  - auog101uan02(DSI) + HDMI
    - imx8mp-rsb3720-a1-auog101uan02.dtb
Camera
- OV5640 (default)
  - imx8mp-rsb3720-a1.dtb
- Basler camrea
  - imx8mp-rsb3720-a1-basler.dtb

ROM-5722

Display
- HDMI (default)
  - imx8mp-rom5722-a1.dtb
- LVDS
  - g070vw01(LVDS0) + HDMI
    - imx8mp-rom5722-a1-lvds0-auo.dtb
  - g070vw01(LVDS1) + HDMI
    - imx8mp-rom5722-a1-lvds1-auo.dtb
  - g215hvn01(DUAL LVDS) + HDMI
    - imx8mp-rom5722-a1-lvds-dual.dtb
- DSI
  - adv7535(DSI to HDMI) + HDMI
    - imx8mp-rom5722-a1-adv7535.dtb
  - auog101uan02(DSI) + HDMI
    - imx8mp-rom5722-a1-auog101uan02.dtb
Camera
- OV5640 (default)
  - imx8mp-rom5722-a1.dtb
- Basler camrea
  - imx8mp-rom5722-a1-basler.dtb

ROM-3620

Display
- LVDS
  - g070vw01
    - imx8mxp-rom3620-a1.dtb
  - g150xgel05
    - imx8qxp-rom3620-a1-lvds-chimei.dtb
  - g215hvn01
    - imx8qxp-rom3620-a1-lvds-dual.dtb
- DSI to HDMI
  - imx8qxp-rom3620-a1-hdmi-bridge.dtb
- DSI
  - auog101uan02
    - imx8qxp-rom3620-a1-auog101uan02.dtb

@@ Line 689: / Line 689: @@
 .Another method for update Kernel and DTB by UUU
-<pre>    # The version of UUU must be <span style="font-size:larger;">'''1.4.139 '''</span><span style="font-size:small;">up</span>
+<pre>    # The version of UUU must be '''1.4.139''' up
      # On U-boot enter fastboot mode
          u-boot > fastboot 0

Difference between revisions of "IoTGateway/BSP/Linux/iMX8/Yocto LBVB User Guide"

Revision as of 05:22, 26 September 2022

Contents

Getting Started

Conventions

Docker install and setting

To install Docker Engine on your platform

To pull ubuntu 18.04 image from Docker Hub

To create container

Get BSP

Download_BSP_From_GitHub

Copy BSP tarball to Container

Downloads tarball

Introducing BSP

Naming Rule

BSP Content

Build Instructions

To create one new build environment

To continue an exist build environment

To build sdcard image

To build toolchain installer

To build bootloader

To build linux kernel

Creating boot-up on-board flash from prebuilt image

To create one boot-up SD card

Creating boot-up on-board flash from built sdcard image

To create one boot-up SD card

Debug console information

Preparing for hardware device

Preparing for software tool

One step build image

Customization

Package addition

To add tcf-agent & openssh-sftp-server

To add chromium browser

To add QtWebEngine

Setting up SDK

Setting up cross compiling environment

Build U-Boot in standalone environment

Config u-boot

Build u-boot

Build imx-boot image by using imx-mkimage

Replace imx-boot

Building & updating kernel/modules/dtb manually

Copy BSP tarball to Container

Config kernel

Replace kernel & dts

Improve boot speed

System Recovery

Package List

Device Tree Source file select

ROM-5721

ROM-5720

ROM-5620

ROM-7720

RSB-3720

ROM-5722

ROM-3620

Burn-in Test

Navigation menu

Search