Difference between revisions of "AIR 020 Development"
(→RS-485) |
(→GPIO Expander) |
||
Line 135: | Line 135: | ||
Test GPIO high/low<br/> [[File:020gpio.jpg|300px|air020gpio.png]] | Test GPIO high/low<br/> [[File:020gpio.jpg|300px|air020gpio.png]] | ||
− | + | [[File:AIR-020 DIO Pin.png|300px|air020gpio.png]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
<br/> 1).Switch to root | <br/> 1).Switch to root |
Revision as of 09:48, 20 June 2023
Contents
Flash Mac Address
GBE in eeprom
$ sudo ./eeprom $SOC $mac_address
Where SOC
186 : TX2-NX 194 : XavierNX 210 : Nano
Intel I210
$ sudo -s $ BDF=`lspci | grep 210 | awk '{print $1}'` $ setpci -s $BDF COMMAND=0007
Get NIC
$./EepromAccessTool
Flash I210 address with mac_address = D4E5F6123456 ( If mac address = D4:E5:F6:12:34:56 )
$ ./EepromAccessTool -nic=<NIC> -f=Dev_Start_I210_Copper_NOMNG_8Mb_A2_3.25_0.03.hex -mac=$mac_address
Cold reboot the device.
Tools
Test Command
JP5.1.0
CAN
$ modprobe can $ modprobe can-dev $ modprobe mttcan $ ip link set can0 type can bitrate 500000 $ ip link set can0 up $ ip link set can1 type can bitrate 500000 $ ip link set can1 up
In other terminal, run below command
$ candump can1
then run
$ cansend can0 123#abcdabcd
WatchDog
root@linux:/home/ubuntu$ sudo -s root@linux:/home/ubuntu# sync; sleep 2; sync; echo c > /proc/sysrq-trigger
TPM
Pre-install TPM-tools
$ sudo apt install --yes tpm2-tools
(1)產生randon code
root@linux:/home/ubuntu# tpm2_getrandom --hex 20
(2) 對指定檔案 msg.dat 加密
root@linux:/home/ubuntu# tpm2_createprimary -C p -c platform_primary.ctx root@linux:/home/ubuntu# tpm2_create -C platform_primary.ctx -G rsa2048 -u key.pub -r key.priv root@linux:/home/ubuntu# tpm2_load -C platform_primary.ctx -u key.pub -r key.priv -c key.ctx root@linux:/home/ubuntu# echo "my test" >msg.dat root@linux:/home/ubuntu# tpm2_rsaencrypt -c key.ctx -o msg.enc msg.dat root@linux:/home/ubuntu# cat msg.enc root@linux:/home/ubuntu# tpm2_rsadecrypt -c key.ctx -o msg.ptext msg.enc root@linux:/home/ubuntu# cat msg.ptext root@linux:/home/ubuntu# cat msg.dat
(3) 將資料儲存至 tpm 內存
root@linux:/home/ubuntu# tpm2_nvdefine -Q 0x1500031 -C o -s 32 -a "ownerread|policywrite|ownerwrite" root@linux:/home/ubuntu# echo "write_tpm_adv" > adv.data root@linux:/home/ubuntu# tpm2_nvwrite -Q 0x1500031 -C o -i adv.data root@linux:/home/ubuntu# tpm2_nvread -Q 0x1500031 -C o -s 32 -o read.data root@linux:/home/ubuntu# cat read.data
(4) 確認已經寫入儲存區域
root@linux:/home/ubuntu# tpm2_nvreadpublic > nv.out root@linux:/home/ubuntu# cat nv.out
Error
ERROR: Esys_NV_DefineSpace(0x14C) - tpm:error(2.0): NV Index or persistent object already defined ERROR: Failed to create NV index 0x1500031.
fixed
root@linux:/home/ubuntu# tpm2_nvundefine 0x1500031
RTC
DUT AC on:
1. Power on DUT and boot into OS.
2. Connect a LAN cable from the DUT to DHCP server.
3. Get a dynamic IP from DHCP server.
4. Type cmd to disable ntp service in DUT.
# sudo timedatectl set-ntp false
5. Synchronize system time and RTC time with NTP server.
# ntpdate tock.stdtime.gov.tw <===安裝ntpdate方式: $sudo apt-get install ntpdate <enter> # hwclock -w
6. Keep the DUT on for 24 hours.
7. Synchronize system time and RTC time with NTP server again and check inaccuracies.
# ntpdate tock.stdtime.gov.tw && hwclock -s &&ntpdate -u tock.stdtime.gov.tw
Camera
The imx219 mode:
Size: Discrete 3280x2464 Interval: Discrete 0.048s (21.000 fps)
Size: Discrete 3280x1848 Interval: Discrete 0.036s (28.000 fps)
Size: Discrete 1920x1080 Interval: Discrete 0.033s (30.000 fps)
Size: Discrete 1640x1232 Interval: Discrete 0.033s (30.000 fps)
Size: Discrete 1280x720 Interval: Discrete 0.017s (60.000 fps)
Preview command:
3280x2464
$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=3280, height=2464, format=NV12, framerate=21/1' ! nv3dsink
3280x1848
$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=3280, height=1848, format=NV12, framerate=28/1' ! nv3dsink
1920x1080
$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1920, height=1080, format=NV12, framerate=29/1' ! nv3dsink
1640x1232
$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1640, height=1232, format=NV12, framerate=29/1' ! nv3dsink
1280x720
$ gst-launch-1.0 nvarguscamerasrc ! 'video/x-raw(memory:NVMM), width=1280, height=720, format=NV12, framerate=59/1' ! nv3dsink
GPIO Expander
1).Switch to root
ubuntu@localhost:~ sudo -s
2).Commnad : where <GPIO> : gpio number and <LEVEL> : high(1)/low(0)
For example, pull up GPIO0 to high.
root@localhost:/home/ubuntu# echo 419 > /sys/class/gpio/export root@localhost:/home/ubuntu# echo out > /sys/class/gpio/PN.01/direction root@localhost:/home/ubuntu# echo 1 > /sys/class/gpio/PN.01/value
UART
RS-232
Xavier-NX
COM1 : COM1_SW1 OFF-OFF-OFF-OFF
stty -F /dev/ttyTHS1 speed 115200 raw -echo cat /dev/ttyTHS1 & echo "1234" > /dev/ttyTHS1
COM2 : COM2_SW1 OFF-OFF-OFF-OFF
stty -F /dev/ttyTHS0 speed 115200 raw -echo cat /dev/ttyTHS0 & echo "1234" > /dev/ttyTHS0
RS-422
Xavier-NX
COM1 : COM1_SW1 ON-OFF-ON-OFF
COM2 : COM2_SW1 ON-OFF-ON-OFF
COM2 -> COM1
stty -F /dev/ttyTHS1 speed 115200 stty -F /dev/ttyTHS0 speed 115200 cat /dev/ttyTHS1 & echo "1234" > /dev/ttyTHS0
COM1 -> COM2
stty -F /dev/ttyTHS0 speed 115200 stty -F /dev/ttyTHS1 speed 115200 cat /dev/ttyTHS0 & echo "1234" > /dev/ttyTHS1
RS-485
Need to adjust the COM port SW1 as shown below.
COM1 : COM1_SW1
COM2 : COM2_SW2
Xavier-NX
COM1 : /dev/ttyTHS1
COM2 : /dev/ttyTHS0
[Hardware flow control]
COM2 -> COM1
COM1_SW1 ON-ON-ON-ON, COM2_SW1 ON-ON-ON-OFF
stty -F /dev/ttyTHS1 speed 115200 stty -F /dev/ttyTHS0 speed 115200 cat /dev/ttyTHS1 & echo "1234" > /dev/ttyTHS0
COM1 -> COM2
COM1_SW1 ON-ON-ON-OFF, COM2_SW1 ON-ON-ON-ON
stty -F /dev/ttyTHS0 speed 115200 stty -F /dev/ttyTHS1 speed 115200 cat /dev/ttyTHS0 & echo "1234" > /dev/ttyTHS1
[Software flow control]
COM1_SW1/COM2_SW1 ON-ON-OFF-OFF
COM2 -> COM1
UART0_RTS (103) : gpio-482 (PX.06)
echo 482 > /sys/class/gpio/export echo out > /sys/class/gpio/PX.06/direction stty -F /dev/ttyTHS1 speed 115200 stty -F /dev/ttyTHS0 speed 115200 cat /dev/ttyTHS1 & echo 1 > /sys/class/gpio/PX.06/value echo "1234" > /dev/ttyTHS0 echo 0 > /sys/class/gpio/PX.06/value
COM1 -> COM2
UART1_RTS (207) : gpio-447 (PR.04)
echo 447 > /sys/class/gpio/export echo out > /sys/class/gpio/PR.04/direction stty -F /dev/ttyTHS1 speed 115200 stty -F /dev/ttyTHS0 speed 115200 cat /dev/ttyTHS0 & echo 1 > /sys/class/gpio/PR.04/value echo "1234" > /dev/ttyTHS1 echo 0 > /sys/class/gpio/PR.04/value
Reference
JP 4.5.1 / JP 4.6.1
AIR-020-RS-485
Calculate GPIO value from pin number