Difference between revisions of "RSB-3810 user guide Android11"

Revision as of 08:03, 6 December 2023 (view source) Jems.cheng (talk | contribs) ← Older edit		Revision as of 08:03, 6 December 2023 (view source) Jems.cheng (talk | contribs) Newer edit →
Line 27:		Line 27:
	 		 
−	=== '''ROM-DB5901 接口布局圖 Board Dimension Layout''' ===
−	'''主板内置插针式引脚排序方式 (Pin Header defination)'''	+	===   ===
	=== '''Internal I/O''' ===		=== '''Internal I/O''' ===

---

Revision as of 08:03, 6 December 2023

產品介紹(Product introduction )

產品特性(Product Features)

• MediaTek Genio 1200 4核心A78和4核心A55
• 內建LPDDR4 8GB，4000MT/s記憶體
• HDMI 4k60fps，1 x 雙通道24位元LVDS
• 1 x 4線RS-232/422/485，2 x USB3.2 Gen1 By 1，2 x USB2.0，1 x Micro SD，1 x Mic. in / Line out
• 1 x M.2 3052 Key B for 5G，1 x M.2 2230 Key E Slot for WiFi/BT
• 支援UIO40-Express I/O板擴充
• 支援Ubuntu、Ycoto Linux和Android

 

產品官網連結(Product official website link)

RSB-3810

硬件接口說明(Hardware interface introduction)

接口布局和尺寸(Layout and Sizes)

ROM-5720 接口布局圖 Board Dimension Layout

 

 

Internal I/O

 

Position	Description	Connector Type
BAT1	PIN Header for Battery	WAFER 8P 2.54mm 180D(M) DIP A2543WV2-8P
BH1	RTC Battery Holder	BATTERY HOLDER 24.9*23.4*8.9 CR2032 BH800.4GG
CAN1	CANBus Port 1	BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10
CAN2	CANBus Port 2	BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10
COM1	COM Port 1	BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10
COM3	COM Port 3 (Debug Port)	BOX HEADER 5x2P 2.54mm 180D(M) DIP 23N6960-10S10
CN4	PCIex1 Connector 1	PCIEXPRESS 36P 180D(F) DIP 2EG01817-D2D-DF
CN5	PCIex1 Connector 2	PCIEXPRESS 36P 180D(F) DIP 2EG01817-D2D-DF
CN6	PCIex1 Connector 3	PCIEXPRESS 36P 180D(F) DIP 2EG01817-D2D-DF
CN11	SATA Connector	Serial ATA 7P 1.27mm 180D(M) DIP WATM-07DBN4A3B8
CN12	SATA Power Connector	WAFER 4P 2.5mm 180D(M) DIP 24W1161-04S10-01T
CN22	GPIOx8 sets	PIN HEADER 10x2P 2.0mm 180D(M) DIP 21N22050
CN25	MXM 3.0 Connector	MXM Conn. 314P 90D(F) SMD AS0B821-S78B-7H
CN26	M.2 Key E Slots	NGFF 75P 0.5mm 90D(F) H=4.2mm SMD AS0BC21-S40BE
CN38	FAN (Reserved)	WTB Con. 3P 2.54mm 180D(M) DIP A2543WV0-3P-6T-5e
CN39	MIPI-CSI1 (FPC, 4-Lane	FPC 39P, 0.6mm, H0.9mm
CN40	MIPI-CSI0 (FPC, 2-Lane)	FPC 39P, 0.6mm, H0.9mm
CN41	MIPI-CSI0 (Mini-SAS, 2-Lane)	Mini SAS 36P/0.8mm/(M)/LCP/VA/G15u/ S/BK/W
CN42	MIPI-CSI1 (Mini-SAS, 4-Lane)	Mini SAS 36P/0.8mm/(M)/LCP/VA/G15u/ S/BK/W
ESPI_CN1	ESPI	PIN HEADER 6x2P 2.0mm180D(M) SMD 21N22050-12M00B
I2C_GP_1	I2C Pin Header	WAFER BOX 4P 2.00mm 180D(M) DIP 721-81-04TW00
I2C_CN3	Audio Codec Board	PIN HEADER 2x10P 2.54mm 180D(M) DIP 21N22564
LVDS0	LVDS0	Wafer 2x20P/1.25mm/(M)/NY9T/VA/GFL/ S/WH/W
LVDS_BK_PWR	LVDS0 Back Light	WAFER BOX 5P 2.0mm 180D(M) DIP A2001WV2-5P
LVDS1	LVDS1	Wafer 2x20P/1.25mm/(M)/NY9T/VA/GFL/ S/WH/W
LVDS1_BK_PWR	LVDS1 Back Light	WAFER BOX 5P 2.0mm 180D(M) DIP A2001WV2-5P
SD1	SD Card Slot	SD CARD 9P 90D(F) SMD WK2192CS3D- 7H
SPI_CN1	SPI Pin Header	PIN HEADER 4x2P 2.54mm 180D(M) SMD 21N22564
SW2	Reset Button	TACT SW STS-091 SMD 4P H=3.8mm
SW4	SLP Button	TACT SW STS-091 SMD 4P H=3.8mm
SW5	Power Button	TACT SW STS-091 SMD 4P H=3.8mm
USB0_OTG1	USB OTG	Micro USB 5P/0.65mm/(F)/NY9T/GFL/ RA/S/BK/B
USB-4-5	USB Port 4, Port 5	PIN HEADER 2x5P 2.0mm 180D(M) SMD 21N22050

Rear I/O

接口引脚定義 (Pin definitions)

• 電池(BAT1) & 電池扣(BH1)
• CAN(CAN1,CAN2)
• 串口(COM_DB(COM3)、COM1、UART0 、UART2)
• 显示接口(LVDS、LVDS Backlight、HDMI、DP)
• LAN接口(LAN)
• USB接口(USB1-2、USB-4-5、USB Type C、USB OTG)
• 音频接口(Audio Output &Audio Codec)
• 电源及指示灯和开关机复位按钮(Power 、LED、Power Button、Reset Button、Sleep Button)
• GPIO接口
• MINI_PCIE接口_M.2接口_SPI、I2C_接口

机械尺寸 (Mechanical Characteristics)

ROM-5720

 Dimensions: SMARC form factor size, 82mm (D) x 50 mm(W)
 Height on Top: Under 3.0 mm base on SPEC definition (without heat sink)
 Height on Bottom: Under 1.3 mm base on SPEC definition

 

 

---

快速入门 (Quick Start)

系统下载 (OS Download)

 

Linux 燒錄方法 (Linux Flash eMMC Method)

使用Flash tool 燒錄鏡像到eMMC (Flash image into eMMC by Flash Tools)

Step0: 檢查SD卡在Linux 環境的代號 (check SD card symbol in Linux system)

 

 

Step1: 創造一張可開機的SD 卡 (Create a bootable SD card)

Step2: 將可開機的SD 卡插入底板SD卡卡槽(Plug the SD card into Carrier board 's SD card slot)

Step4: 確認開機選擇指撥開關

SD 卡開機模式:

Step3:打開電源 和 終端機 (Turn on the Power & Terminal)

 

Step4: 壓縮flash tools 檔案,並複製到U盤中(the flash tools file , then copy to USB Disk)

Step 5: Yocto 系統會自動掛載 U盤 在(run/media/sda1下)

並拷貝 5720A1AIM30LIVA0271_iMX8M_2G_flash_tool.tgz 到根目錄 (copy the file into Yocto system)

     Commnd :  cp -a  5720A1AIM30LIVA0271_iMX8M_2G_flash_tool.tgz  /

在Yocto 系統中解壓縮(Unzip the file in Yocto system on ROM-5720)

Step 6. 燒錄eMMC 鏡像 (flash image into eMMC flash by flash tool file)

  command : ./mksd-linux.sh /dev/mmcblk0

 

Step 7 . 結束燒錄後, 請改變撥碼開關至 1 on , 其他 off (eMMC開機模式) (Finish the flash process, please chanage the switch (SW1) to 1 on , others off )

 

移除SD卡, 拔除電源 ,改變撥碼開關 (unplug the SD card , turn off power , change the SW1 switch to eMMC mode (1 on , others off)

eMMC mode : 1 on , others off

Step 8. 重新上電開機 ( Turn on the power , then check the Debug message)

Debug 串口調試 (Debug port Setting)

以 Tera Term 为例介绍如何使用串口调试功能

   Baud Rate波特率：115200
   Data 数据位：8
   Parity 奇偶校验：无
   Stop 停止位：1
   Flow Control流控：无

 

Tera Term Tool

 

Check the Sriel port in Device Manager (查看PC端的串口号)：

if you can not identify the Serial device , please check your serial driver.

 

Debug port connection (串口連接)

 

Log into Terminal Tool (进入串口调试终端)：

 

Linux系统的基本使用(Linux System Basic Operating Method)

UUU 使用方法(USB Connection (OTG port))

Display Setting (ROM-5720)

U-boot Command :

setenv fdt_file imx8mq-rom5720-a1-dcss-adv7535.dtb
env save
boot 

Yocto 2.5

 

• Display
  • DSI to HDMI
    • adv-imx8mq-rom5720-a1-dcss-adv7535-b3.dtb
    • adv-imx8mq-rom5720-a1-lcdif-adv7535.dtb
  • DSI
    • auog101uan02
      • adv-imx8mq-rom5720-a1-dcss-auog101uan02.dtb
  • Dual Display
    • DSI to HDMI + HDMI
      • adv-imx8mq-rom5720-a1-dual-display.dtb
• M.2 SDIO
  • Adjust CN43~CN48
  • adv-imx8mq-rom5720-a1-m2-sdio.dtb
• M.2 I2S
  • adv-imx8mq-rom5720-a1-m2-i2s.dtb

 

Yocto 3.0

• Display
  • DSI to HDMI
    • imx8mq-rom5720-a1-dcss-adv7535.dtb
    • imx8mq-rom5720-a1-lcdif-adv7535.dtb
    • For weston ui
      • modify /etc/xdg/weston/weston.ini
        • drm-device=card2
  • DSI
    • auog101uan02
      • imx8mq-rom5720-a1-dcss-auog101uan02.dtb
  • Dual Display
    • DSI to HDMI + HDMI
      • imx8mq-rom5720-a1-dual-display.dtb
      • For weston ui
        • modify /etc/xdg/weston/weston.ini
          • drm-device=card1
• M.2 SDIO
  • Adjust CN43~CN48
  • imx8mq-rom5720-a1-m2-sdio.dtb

乙太網路使用方法(Ethernent Testing Method)

Command : ifconfig

 

Command: Ping - I eth1 8.8.8.8

WiFi使用方法(WIFI Testing Method)

Command : 

#killall wpa_supplicant
# ifconfig wlan0 up
# wpa_passphrase "SSID" "PASSWORD" > /tmp/wpa.conf
# wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
# udhcpc -b -i wlan0

ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms

 

4G使用方法(4G Testing Method)

Command:
Test 4G: (EWM-C117FL06E - USB)
      Step 1: Connect EWM-C117FL06E to Mini PCIE slot on 9680015491 and connect
                   the card to CN6 PCIe_D slot on ROM-DB5901.
      Step 2: Connect the antenna 1750007990-01 to the SMA (F) connector on
                   9680015491 and connect the IPEX connector to MT1 on EWM-C117FL06E module.
      Step 3: Connect the Mini USB cable from 9680015491 to USB 2.0 Type A port on
                   ROM-DB5901.
      Step 4: Power on and execute the pppd command to connect to the network.

GPIO使用方法(GPIO Operating Method)

Loop-back Test (Take GPIO4 and GPIO5 as examples)

Step 1: Connect GPIO4 and GPIO5
Step 2: Export GPIO interface

root@imx8mqrom5720a1 : ~# echo 0 > /sys/class/gpio/export
root@imx8mqrom5720a1 : ~# echo 132 > /sys/class/gpio/export

Step 3: Set direction

root@imx8qxprom5720a1 : ~# echo out > /sys/class/gpio/gpio1/direction
root@imx8qxprom5720a1 : ~# echo in > /sys/class/gpio/gpio2/direction

Step 4: Read value and set output value then check

root@imx8mqrom5720a1 : ~# cat /sys/class/gpio/gpio2/value
1
root@imx8mqrom5720a1 : ~# echo 0 > /sys/class/gpio/gpio1/value
root@imx8mqrom5720a1 : ~# cat /sys/class/gpio/gpio2/value
0

 

 

 

串口使用方法(Serial Port Operating Method)

RS-232 Test

COM0: CN15A:上(SER0/UART3): /dev/ttymxc2

COM2: CN15B:下(SER2/UART2): /dev/ttymxc1

COM3: (A53 debug/SER3/UART1): /dev/ttymxc0

COM1: (M4 debug/SER1/UART4): /dev/ttymxc3

Loopback test (eg. ttymxc1)
Before loopback test, we should connect tx and rx

<span style="background:#eeeeee">stty -F /dev/ttymxc1 115200

stty -F /dev/ttymxc1 ?echo

cat /dev/ttymxc1 &

echo test > /dev/ttymxc1</span>

=== 蓝牙使用方法(BlueTooth Operating Method) ===
Command :

$ hciconfig hci0 up
$ bluetoothctl
$ discoverable on
$ pairable on
$ scan on
[NEW] FC:18:3C:8D:75:F4 myphone
$ scan off
$ pair FC:18:3C:8D:75:F4
$ connect FC:18:3C:8D:75:F4</pre>

遠程訪問及文件傳輸(Remote Access and File Transimmion)

查看主板IP位址 ( Chech IP Address )：​
Command : ifconfig

 

Windows下SSH访问及文件传输

SSH Remote Log into Device

• SSH远程登录,以putty选择putty.exe(或者使用Xshell、SecureCRT等类似软件)
  *需要设置远程设备的IP、通讯端口(默认22)、通讯方式，登录后验证用户名密码

 

 

通用方法(General Method)

=== 查看CPU温度(Check CPU Temperature) ===
root@imx8qxprom5720a1:/# cat /sys/devices/virtual/thermal/thermal_zone0/temp 44600

1. 或者直接以度爲單位顯示 echo $[$(cat /sys/class/thermal/thermal_zone0/temp)/1000]° >>> 45°</pre>

=== 查看CPU频率(Check CPU Frequency) ===
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
>> 900000
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
>> 1200000

=== 查看内存容量(Check Memory Capacity) ===
root@imx8qxprom5720a1:/# busybox free -m
total used free shared buffers cached
Mem: 1794920 516080 1278840 17252 9852 80292
-/+ buffers/cache: 425936 1368984
Swap: 0 0 0

=== 查看存储容量(Check Storage Capacity) ===
root@imx8qxprom5720a1:/# busybox df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 13.4G 1.7G 11.1G 13% /
devtmpfs 395.8M 4.0K 395.8M 0% /dev
tmpfs 876.4M 0 876.4M 0% /dev/shm
tmpfs 876.4M 16.5M 859.9M 2% /run
tmpfs 876.4M 0 876.4M 0% /sys/fs/cgroup
tmpfs 876.4M 4.0K 876.4M 0% /tmp
tmpfs 876.4M 280.0K 876.2M 0% /var/volatile
/dev/mmcblk0p2 13.6G 1.7G 11.3G 13% /run/media/mmcblk0p2
/dev/mmcblk0p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk0p1
/dev/mmcblk1p1 63.9M 23.4M 40.5M 37% /run/media/mmcblk1p1
tmpfs 175.3M 88.0K 175.2M 0% /run/user/0
root@imx8qxprom5720a1:/#

=== 網路Ping測試(Ping Network Testing) ===
ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=54 time=2.10 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=54 time=2.10 ms</pre>

=== 設置RTC (RTC Setting) ===
root@imx8qxprom5720a1:/# systemctl stop ntpdate.service
root@imx8qxprom5720a1:/# date 090816072021 && hwclock -w && date
Wed Sep 8 16:07:00 UTC 2021
Wed Sep 8 16:07:00 UTC 2021
root@imx8qxprom5720a1:/# date
Wed Sep 8 16:07:06 UTC 2021
root@imx8qxprom5720a1:/#

Mic錄音 (Mic record)

1. amixer set Mic 20%

1. arecord -D plughw:0,0 -r 16000 -f S16_LE ./f-16000.wav

1. aplay ./f-16000.wav

PCIe裝置移除與rescan

root@imx8qxprom5720a1:/# echo "1" > /sys/bus/pci/devices/0000\:01\:00.0/remove --eth1 will be remove (check with ifconfig)

root@imx8qxprom5720a1:/# echo "1" > /sys/bus/pci/rescan --eth1 will back after run this command.

 

Linux BSP編譯方法(Linux BSP Compile Method)

 

如果有驗證上的錯誤 請使用以下的方法

### repo sync failed with Server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none
============================================================
export GIT_SSL_NO_VERIFY=1
#or
git config --global http.sslverify false
============================================================