Difference between revisions of "Using RKTool for ASR-A501."
From ESS-WIKI
Xingxing.li (talk | contribs) |
Xingxing.li (talk | contribs) |
||
| Line 28: | Line 28: | ||
[[File:ASR-A501 OTG Step 2.png|RTENOTITLE]] | [[File:ASR-A501 OTG Step 2.png|RTENOTITLE]] | ||
| − | === '''The test environment is set up as follows:''' | + | === '''Hardware Pin Definition：''' === |
| + | |||
| + | {| border="1" cellpadding="1" cellspacing="1" | ||
| + | |- | ||
| + | | colspan="2" | '''CAN/DEBUG Connector''' | ||
| + | |- | ||
| + | | '''Pin''' | ||
| + | | '''Pin Name''' | ||
| + | |- | ||
| + | | 1 | ||
| + | | TX_DEBUG | ||
| + | |- | ||
| + | | 2 | ||
| + | | RX_DEBUG | ||
| + | |- | ||
| + | | 3 | ||
| + | | GND | ||
| + | |- | ||
| + | | 4 | ||
| + | | GND | ||
| + | |- | ||
| + | | 5 | ||
| + | | CAN2_H | ||
| + | |- | ||
| + | | 6 | ||
| + | | CAN2_L | ||
| + | |- | ||
| + | | 7 | ||
| + | | CAN1_H | ||
| + | |- | ||
| + | | 8 | ||
| + | | CAN1_L | ||
| + | |} | ||
| + | |||
| + | === === | ||
| + | |||
| + | '''Debugging wiring method for cables.（Debug cable Number：1700035538-01 ）''' | ||
| + | |||
| + | TX——>DB9 Pin 3, RX——>DB9 Pin2, GND——>DB9 Pin5 | ||
| + | |||
| + | | ||
| + | |||
| + | '''The test environment is set up as follows:''' | ||
[[File:ASR-A501 OTG Step3.png|RTENOTITLE]] | [[File:ASR-A501 OTG Step3.png|RTENOTITLE]] | ||
Revision as of 09:59, 19 March 2026
Contents
- 1 For example, the PC used is a laptop. The specifications are as follows：
- 2 Open the following file, follow the steps and double-click to install the DriverInstall program, as shown in the figure below:
- 3 Go to the RKDevTool_Release folder and run the RKDevTool.exe program.
- 4 Hardware Pin Definition：
- 5
- 6 Open the putty tool, enter the MASKROM mode through the debug port, then click "Execute" to start burning the OS.
- 7 After burning, open putty to check the image version.
For example, the PC used is a laptop. The specifications are as follows：
Decompress the downloaded image on the PC.
Open the following file, follow the steps and double-click to install the DriverInstall program, as shown in the figure below:
Change Tool language in config.ini, please change "Selected: to "2"
选择工具语言:Selected=1(中文)<--Chinese ;Selected=2(英文)<-- English [Language] Kinds=2 Selected=2 LangPath=Language\
Go to the RKDevTool_Release folder and run the RKDevTool.exe program.
Note: Please ensure that the path for burning the file is correct.
Hardware Pin Definition：
| CAN/DEBUG Connector | |
| Pin | Pin Name |
| 1 | TX_DEBUG |
| 2 | RX_DEBUG |
| 3 | GND |
| 4 | GND |
| 5 | CAN2_H |
| 6 | CAN2_L |
| 7 | CAN1_H |
| 8 | CAN1_L |
Debugging wiring method for cables.（Debug cable Number：1700035538-01 ）
TX——>DB9 Pin 3, RX——>DB9 Pin2, GND——>DB9 Pin5
The test environment is set up as follows:
Open the putty tool, enter the MASKROM mode through the debug port, then click "Execute" to start burning the OS.
Method 1: After powering on and starting up, press "Ctrl+C" to enter "u-boot", input the "rbrom" command, and enter the MASKROM mode.
Debian ：
Hit any key to stop autoboot: 0 rkboot # <INTERRUPT> rkboot # rbrom
Method Two: Press the "MASKROM" button, then power on and turn on the device, and it will directly enter the MASKROM mode.
After burning, open putty to check the image version.
