Difference between revisions of "EIS Docker Container Base"
From ESS-WIKI
Eric.liang (talk | contribs) |
Eric.liang (talk | contribs) |
||
| Line 1: | Line 1: | ||
= Introduction = | = Introduction = | ||
| − | |||
| − | |||
= Specification = | = Specification = | ||
| − | |||
| − | |||
= Release Note = | = Release Note = | ||
| − | |||
| − | |||
= EIS SW Service = | = EIS SW Service = | ||
| Line 41: | Line 35: | ||
| − | |||
| + | = How to Guide = | ||
== Delopy EIS Image to USB or HDD Disk == | == Delopy EIS Image to USB or HDD Disk == | ||
| Line 76: | Line 70: | ||
| + | |||
| + | == == | ||
== Development == | == Development == | ||
| + | |||
| + | === WSN Simulator === | ||
| + | |||
| + | Start and enter the WSN Simulator Docker Container bash | ||
| + | <pre>$cd ~/Advantech /docker | ||
| + | |||
| + | $./deploy.sh wsn-sim.sh</pre> | ||
| + | |||
| + | You can design and edit your wsn type and senhub information. You can refer [[IoTGateway/Net_HAL_Simulator|IoTGateway/Net HAL Simulator]] for detail information. | ||
| + | |||
| + | Start running the wsn-simulator. It will simulate WSN connectivity and senhub and send data to mqtt bus. | ||
| + | <pre>#./wisesim</pre> | ||
| + | |||
| + | Exit the container service | ||
| + | <pre>#exit</pre> | ||
| + | |||
| + | |||
| + | |||
| + | === WSN Development Environment === | ||
| + | |||
| + | Start and enter the WSN Development Docker Container bash | ||
| + | <pre>$cd ~/Advantech /docker | ||
| + | |||
| + | $./deploy.sh wsn-dev.sh</pre> | ||
Revision as of 06:33, 20 February 2017
Introduction
Specification
Release Note
EIS SW Service
Docker Container Services
api-gw
dust-link
mqtt-bus
hdd-pmq
node-red
wsn nodes
hdd-pmq node
Management
Webmin webadmin
Kitematic
Cloud-Solution
WISE-PaaS WISE-Agent
How to Guide
Delopy EIS Image to USB or HDD Disk
To check USB or HDD Disk name
sudo fdisk -l
Deploy the image to USB flash drive . Note: The deploy process takes about 15 minutes.
sudo dd if=./EIS_V2.0.2_Ubuntu-14.04_3.19_20170220.img of=/dev/sdx bs=4M; sync
Boot for USB or HDD Disk
- Insert the USB Flash / HDD Drive into the ARK-2121L
- Boot up to the BIOS menu of your ARK-2121L by pressing ESC on the keyboard as it boots up.
- Change the boot device to be the USB/HDD flash drive, then press F4 to save and exit
- System should boot up using the USB Flash Drive.
- Log in as user: adv password: adv
- The EIS Version 2 is ready to use.
Re-size EIS File System
#sudo fdisk /dev/sdb d -> 2 : delete partition 2 n -> p -> 2 : w : write result #reboot #resize2fs /dev/sdb2
Check and Upgrade the EIS Docker Service to latest version
cd ~/Advantech/docker ./deploy.sh update
Development
WSN Simulator
Start and enter the WSN Simulator Docker Container bash
$cd ~/Advantech /docker $./deploy.sh wsn-sim.sh
You can design and edit your wsn type and senhub information. You can refer IoTGateway/Net HAL Simulator for detail information.
Start running the wsn-simulator. It will simulate WSN connectivity and senhub and send data to mqtt bus.
#./wisesim
Exit the container service
#exit
WSN Development Environment
Start and enter the WSN Development Docker Container bash
$cd ~/Advantech /docker $./deploy.sh wsn-dev.sh