Edge Sense LoRa GW Solution

Introduction

An IoT total solution, mainly composed of UTX-3117 gateway/EIS-D210 gateway, RYLR89D Lora demo board and WISE-PaaS.

Gateway Support Lists

• UTX-3117
• EIS-D210

Support Node

node type #1
Sensor：Temperature , Humidity , LED x 5 , ADC , Relay x 4 , Input x 4

node type #2
Sensor：Temperature , Humidity , CO2

node type #3
Sensor：GPS

Files Archives

[1]

Release

• ReyaxSol 0.0.1 (for 2018 embedded world)
• ReyaxSol 0.0.2
• ReyaxSol 0.0.3
• ReyaxSol 1.0.0-rc1 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0-rc2 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0-rc3 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0-rc4 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0-rc5 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0-rc6 (for Ubuntu 16.04 for QA Test)
• ReyaxSol 1.0.0 (for Ubuntu 16.04 for QA Test)

Change Logs

1.0.0

• Based on 1.0.0-rc6 to formal release.

1.0.0-rc6

• Fix bug: 5235

1.0.0-rc5

• Fix bug: 5266, 5235, 5231

1.0.0-rc4

• Fix bug: 5227, 5228, 5229, 5231, 5235

1.0.0-rc3

• Support LoRa module Version RYLRxxP_V0.1.22

1.0.0-rc2

• Support LoRa module Version RYLRxxP_V0.1.13
• Support crfop, band, address, networkid in config file
• Install ReyaxSol to system's folder , not to /home/adv
• Added uninstall mechanism
• Fixed same gateway device id shown on WISE-PaaS from different gateway

1.0.0-rc1

• Support LoRa module Version RYLRxxP_V0.1.2

Tools

Check version

In Linux, execute command:
$ cat /usr/local/EdgeSense/LoRaMgt_ryx/version
1.0.0

Monitor Tools

reyaxmon is a monitor tool that it will show RF setting , gateway setting and sensor value from LoRa nodes.

Execute following commands to launch reyaxmon tools.
$ cd /usr/local/EdgeSense/LoRaMgt_ryx
$ sudo ./reyaxmon

RTENOTITLE

Reyax AT Command Demo Script

This demo script is a simple bash script, aim to provide a preliminary understanding about Reyax At Command.

Script version : 0.3-beta

Support Reyax firmware version : RYLRxxP_V0.1.22

Download

• This demo script is available at Reyax-atcmd-demo.bash.tar.gz
• Download the file and upload it to Ubuntu. (Execute "wget http://ess-wiki.advantech.com.tw/wiki/images/4/4b/Reyax-atcmd-demo.bash.tar.gz" in terminal)
• Uncompress the file with command "tar zxfv Reyax-atcmd-demo.bash.tar.gz" , then reyax-atcmd-demo.bash will be ready to use.

Usage

1. In Ubuntu Desktop , open two terminals.
2. Terminal 1 (Left) , run "sudo cat /dev/ttyUSB0"
3. Terminal 2 (Right) , run "sudo ./reyax-atcmd-demo.bash"
   
4. You can enter your choice in the right terminal to issue AT command
5. Message from AT Command RX will be shown in the left terminal.
6. If you want to change node address , press 0 to enter new node's address.