Edge Sense LoRa GW Solution
Contents
Introduction
An IoT total solution, mainly composed of UTX-3117 gateway/EIS-D210 gateway, RYLR89D Lora demo board and WISE-PaaS.
Topology:
Gateway Support Lists
Support Node
node type #1
Sensor：Temperature , Humidity , LED x 5 , ADC , Relay x 4 , Input x 4
(NOTE：SW 1.0.0 only support Temperature , Humidity , LED x 5 , ADC)
(NOTE：Relay x 4, Input x4 need to running SW 1.0.1-rc1 above, but not yet testing)
node type #2
Sensor：Temperature , Humidity , CO2
(NOTE：SW 1.0.0 support CO2 , but CO2 sensor not yet testing)
node type #3
Sensor：GPS
(NOTE：This node type and GPS sensor need to running SW 1.0.1-rc1 above, but not yet testing)
Release Note
LoRaMgt_ryx 1.0.1-rc1 (for Ubuntu 16.04) (Not yet testing)
- Support Minipcie LoRa module firmware Version RYLRxxP_V0.1.28
- Support LoRa nodetype#1 firmware version: RYLRxx6_V0.1.20 + RYLRxxE_V0.1.11 (for I/O board)
- Support LoRa nodetype#2 firmware version: RYLRxx2_V0.1.20
- Support LoRa nodetype#3 firmware version: RYLRxxS_V0.1.20
- Support sensor: Input x 4 , Relay x 4 , GPS
- LoRaMgt_ryx install package : \\eossfs\EdgeSense\Project\ReyaxSolution\Release\LoRaMgt_ryx-1.0.1-rc1-Ubuntu_16.04-x86_64.run
- RMM Agent install package: \\eossfs\EdgeSense\Project\ReyaxSolution\Release\rmmagent-Ubuntu 16.04.4 LTS x86_64-3.3.23.8242.run
LoRaMgt_ryx 1.0.0 (for Ubuntu 16.04)
- Support Minipcie LoRa module firmware Version RYLRxxP_V0.1.22
- Support LoRa nodetype#1 firmware version: RYLRxx6_V0.1.13 + RYLRxxE_V0.1.7.hex (for I/O board)
- Support LoRa nodetype#2 firmware version: RYLRxx2_V0.1.13
- Support sensor: Temperature , Humidity , LED x 5 , ADC, CO2
- Support maxinum 4 nodes
- Support RMM 3.3
- Command line monitor tools
- LoRaMgt_ryx install package : \\eossfs\EdgeSense\Project\ReyaxSolution\Release\LoRaMgt_ryx-1.0.0-Ubuntu_16.04-x86_64.run
- RMM Agent install package: \\eossfs\EdgeSense\Project\ReyaxSolution\Release\rmmagent-Ubuntu 16.04.4 LTS x86_64-3.3.23.8242.run
Install Steps
- Install OS - Ubuntu 16.04.4 (ubuntu-16.04.4-desktop-amd64.iso)
- Copy RMM Agent install package (ex: rmmagent-Ubuntu 16.04.4 LTS x86_64-3.3.23.8242.run) to gateway.
- Copy LoRaMgt_ryx install package (ex: LoRaMgt_ryx-1.0.0-Ubuntu_16.04-x86_64.run) to gateway.
- Execute "sudo chmod +x LoRaMgt_ryx-1.0.0-Ubuntu_16.04-x86_64.run".
- Execute "sudo ./LoRaMgt_ryx-1.0.0-Ubuntu_16.04-x86_64.run" to install.
- Execute "sudo chmod +x rmmagent-Ubuntu 16.04.4 LTS x86_64-3.3.23.8242.run".
- Execute "sudo ./rmmagent-Ubuntu 16.04.4 LTS x86_64-3.3.23.8242.run" to install RMM Agent.
Then, it will be installed in gateway.
Installation consist of
- Install configure file to /usr/local/EdgeSense/LoRaMgt_ryx/settings.ini
- Install LoRa Management for Reyax
- Install RMM agent for RMM 3.3
- Install MQTT broker
- Install Node.js
- Install other library dependencies
- Install Reyax_AT_Command_Demo_Script
After installation, service will be autorun.
NOTE: Please wire the gateway to Internet with Network cable before install, it is necessary to install the dependencies.
Uninstall Steps
Execute "sudo /usr/local/EdgeSense/LoRaMgt_ryx/uninstall.bash" in terminal.
Execute "sudo /usr/local/AgentService/uninstall.sh" in terminal to uninstall RMM Agent.
Config File
You can execute "sudo vi /usr/local/EdgeSense/LoRaMgt_ryx/settings.ini" command in Ubuntu terminal to modify config.
Once config is changed , please execute "sudo systemctl restart LoRaMgt_ryx.service" to restart service in order to apply new setting.
|
[gateway] [rf] [node-2] |
SerialPort
- Assign uart device for Reyax pcie LoRa module
node_num
- Support maxinum 64 nodes
polling_rate
- range from 5 to 3600 second, default value is 20 second
- If setting is greater than maximum value or is less than minimum value, it will use default value.
band
- option :
- TW - for Taiwan
- JP - for Japan
- KR - for Korea
- US - for US
hostaddr
- Assign address for LoRa Host (LoRa pcie module inside gateway)
networkid
- Network ID, default is 0, range from 0 to 16
- NOTE：In firmware RYLRxxP_V0.1.22, range from 0 to 5
crfop1 / crfop2
- LoRa module power , range from 0 to 15 dBm
addr:
- address for LoRa Node.
notetype:
- nodetype=1 : temperature + humidity + output x 5 + adc + relay x 4 + input x 4
- nodetype=2 : temperature + humidity + co2
- nodetype=3 : GPS
Tools
Check version
In Linux, execute command:
$ cat /usr/local/EdgeSense/LoRaMgt_ryx/version
1.0.0
Monitor Tools
reyaxmon is a monitor tool that it will show RF setting , gateway setting and sensor value from LoRa nodes.
Execute following commands to launch reyaxmon tools.
$ cd /usr/local/EdgeSense/LoRaMgt_ryx
$ sudo ./reyaxmon
Reyax AT Command Demo Script
This demo script is a simple bash script, aim to provide a preliminary understanding about Reyax At Command.
Script version : 0.3-beta
Support Reyax firmware version : RYLRxxP_V0.1.22
Support Lora Proprietary Command Set : V0.97
Download
- This demo script is available at Reyax-atcmd-demo.bash.tar.gz
- Download the file and upload it to Ubuntu. (Execute "wget http://ess-wiki.advantech.com.tw/wiki/images/4/4b/Reyax-atcmd-demo.bash.tar.gz" in terminal)
- Uncompress the file with command "tar zxfv Reyax-atcmd-demo.bash.tar.gz" , then reyax-atcmd-demo.bash will be ready to use.
Usage
- In Ubuntu Desktop , open two terminals.
- Terminal 1 (Left) , run "sudo cat /dev/ttyUSB0"
- Terminal 2 (Right) , run "sudo ./reyax-atcmd-demo.bash"
- You can enter your choice in the right terminal to issue AT command
- Message from AT Command RX will be shown in the left terminal.
- If you want to change node address , press 0 to enter new node's address.
