Frequently Asked Questions for i.MX6 Linux

Compiling

U-boot

Please refer to the following sections for details

• Getting Started / Build Instructions / To build u-boot _{(LBV3) (LBV5) (LBV6)}

• Customization / Building & updating u-boot manually _{(LBV3) (LBV5) (LBV6)}

Kernel

Please refer to the following sections for details

• Getting Started / Build Instructions / To build linux kernel _{(LBV3) (LBV5) (LBV6)}
• Customization / Building & updating kernel/modules/dtb manually _{(LBV3) (LBV5) (LBV6)}

Boot Logo

Kernel

In Yocto Project, it is called "boot splashscreen", please refer to the each BSP's corresponding official Yocto website (list as below) for details

• Yocto Project Reference Manual / Other Tips. _{(LBV3) (LBV5) (LBV6)}

SDcard image

To build from prebuilt image, please refer to the following sections for details.

• Getting Started / Introducing BSP / Prebuilt image _{(LBV3) (LBV5) (LBV6)}

To build from BSP, please refer to the following sections for details.

• Getting Started / Build Instructions / To build sdcard image _{(LBV3) (LBV5) (LBV6)}

How To Stress Test On a Linux

Perform the command as below:

stress -c 4 -i 4  -d 1 --hdd-bytes 512

How to fix sata can't be detected issue

find ahci_imx.c in kernel source code

drivers/ata/ahci_imx.c

Mark modification as below:

      // else if(IS_RSB_4411)
      // {
      //         sata_gen_phy_reg[0] = 0x059194f6;
      //         sata_gen_phy_reg[1] = 0x059194f6;
      //         sata_gen_phy_reg[2] = 0x059194f6;
      //}
       

This modification are sata si test value, but it may result in some sata disk can't be detected

How To Create One LIV Disk Image of SD Card

The LIV disk image of SD card is used to boot target device up and to install the entire system to on-baord eMMC.

• Prerequisites
  1. one free loop device
  2. prewritten script, mksd-linux.sh (extracted from mksd-linux.sh.gz)
  3. the built sdcard image _{(LBV3) (LBV5) (LBV6)} (e.g. fsl-image-qt5-imx6qrsb4410a1.sdcard)
  4. 5GB more available disk space for LIV disk image (e.g. 4410A1LIV6000.img & 4410A1LIV6000.img.gz)
• Commands

$ LODEV=$(sudo losetup -f)
$ MKSD=mksd-linux.sh
$ gunzip -c mksd-linux.sh.gz > ${MKSD}
$ SDCARD=fsl-image-qt5-imx6qrsb4410a1.sdcard
$ LIV=4410A1LIV6000.img
$ cp ${SDCARD} ${LIV}
$ dd if=/dev/zero of=${LIV} bs=1M seek=3700 count=0
$ echo -e "d\n2\nn\np\n2\n24576\n\nw" | sudo fdisk -u ${LIV}
$ sudo losetup -o $((24576*512)) ${LODEV} ${LIV}
$ sudo e2fsck ${LODEV}
$ sudo resize2fs ${LODEV}
$ mkdir -p ~/mnt
$ sudo mount ${LODEV} ~/mnt
$ sudo mkdir ~/mnt/{mk_inand,image}
$ sudo cp ${MKSD} ~/mnt/mk_inand/
$ sudo chmod +x ~/mnt/mk_inand/${MKSD}
$ sudo cp ${SDCARD} ~/mnt/image/
$ sudo umount ~/mnt
$ sudo losetup -d ${LODEV}
$ gzip -c9 ${LIV} > ${LIV}.gz

Other Features

• see Linux Features