Test Report vA0076

From ESS-WIKI
Jump to: navigation, search
Project Test Image Version
RSB-3720 A0 CPU Yocto Linux imx8mprsb3720a1 5.4.24-3720A1AIM30LIVA0076


No Module Test Item Test Steps Remark Result Result Comment
1 CPU CPU Cores $ cat /proc/cpuinfo A53 x 4 PASS
CPU Max MHz $ cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq 1800000 PASS
2 DDR Memory Size $ cat /proc/meminfo LPDDR4   6GB PASS MemTotal:        6002660 kB
Memory Clocks Check memory clock under boot loader N/A
DDR parameter Version Check info in bootloader PASS ATF b0a00f2
U-Boot 2020.04-3720A1AIM30LIVA0068+g121029b89f
3 Stress Test Stress Test Refer to /tools/stress.sh Need to verify w/o cooling  PASS 15 hr pass
4 SD Card Access Mount and read/write/verify data under kernel PASS
Write Protect Check WP function N/A Default Off
5 Additional SD Slot Access Mount and read/write/verify data under kernel N/A
Write Protect Check WP function N/A
6 eMMC eMMC 16GB Write/Read/Verify data in the start/end 4 byte of flash PASS
7 Debug UART UART 4 A53 control:
$ stty -F /dev/ttymxc3 -echo -onlcr 115200
$ cat /dev/ttymxc3 &
$ echo "Serial Port Test" > /dev/ttymxc3
M7_Debug:
(1) emmc boot:
U-Boot > fatload mmc 2:1 0x48000000 imx8mp_m7_TCM_hello_world.bin;cp.b 0x48000000 0x7e0000 20000;
U-Boot > bootaux 0x7e0000
(2) sd card boot:
U-Boot > fatload mmc 1:1 0x48000000 imx8mp_m7_TCM_hello_world.bin;cp.b 0x48000000 0x7e0000 20000;
U-Boot > bootaux 0x7e0000 		A53 control: /dev/ttymxc3
or
M7_Debug
2 wire (EXTENSION I/O B - COM4)
UIO4032 COM_4 		PASS
UART 3 A53_Debug
4 wire (COM1 Pin Header) 		PASS
8 RS-232 UART 1 bcm43xx:
$ hciattach /dev/ttymxc0 bcm43xx 115200 flow 		4 wire (M.2)
/dev/ttymxc0 		PASS
UART 2 $ stty -F /dev/ttymxc1 -echo -onlcr 115200
$ cat /dev/ttymxc1 &
$ echo "Serial Port Test" > /dev/ttymxc1 		2 wire (EXTENSION I/O B - COM2)
UIO4032 COM_3
/dev/ttymxc1 		PASS
9 RS-485/422 UART 3 1. Test RS-485 with Adam-4520. Adam-4520 Pin 1: Data- and Pin 2: Data+ connect to RSB-3720 COM1 Pin 1: COM_DCD and Pin 3: COM_RXD
$ stty -F /dev/ttymxc2 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke
$ cat /dev/ttymxc2 &
$ echo "Serial Test" > /dev/ttymxc2 		4 wire (COM1 Pin Header)
Set GPIO#496, #497
Set to 0,1 for RS-485
Set to 1,1 for RS-422
Set to 0,0 for loopback
Set to 1,0 for RS-232
Remember to set up RS-485 before test.
$ ./enable485 /dev/ttymxc2 		PASS
N/A N/A
N/A N/A
N/A N/A
10 SPI Bus QSPI 0A Write/Read/Verify data in the start/end 4 byte of flash
Note:Make sure the content of SPI nor flash is erased

$ echo -n $'\x06\x05\x04\x03\x02\x01' > test
$ dd if=test of=/dev/mtd0
$ hexdump -C /dev/mtd0 -n 64 		SPI Rom PASS
N/A N/A
N/A N/A
N/A N/A
N/A N/A
11 GPIO GPIO pins Set direction (in/out) and value (0/1) 10 pins
[EXTENSION I/O A]
pin#2: gpio 501
pin#4: gpio 503
[EXTENSION I/O B]
pin#5: gpio 504
pin#6: gpio 505
pin#7: gpio 506
pin#8: gpio 507
pin#9: gpio 508
pin#10: gpio 509
pin#11: gpio 510
pin#12: gpio 511 		PASS
12 PCIe N/A Device detect under kernel M.2 PASS lspci (EWM-163)
13 M.2 UART 1 bcm43xx:
$ hciattach /dev/ttymxc0 bcm43xx 115200 flow 		PASS verify with AW-NB136NF 
SDIO dmesg | grep SDIO
=> mmc0: new ultra high speed SDR104 SDIO card at address 0001 		PASS verify with AW-NB136NF 
PCIe 3.0 PASS Verify with EWM-W163
USB 2.0 PASS Verify with EWM-W163
I2S SAI2 No test equipment
14 3G Modules $ stty -F /dev/ttyUSB3 -echo
$ cat /dev/ttyUSB3 &
$ echo -e "AT+CPIN?" > /dev/ttyUSB3
+CPIN: READY
OK
$ pppd connect 'chat -v -s -t 10 "" "AT" "" "ATDT*99#" "CONNECT" ""' user username password password /dev/ttyUSB3 460800 nodetach crtscts debug usepeerdns defaultroute & 		PASS AirPrime MC8090
15 WiFi Modules $ ifconfig wlan0 up
$ wpa_passphrase ASUS-917C qwert12345 > /tmp/wpa.conf && wpa_supplicant -BDwext -iwlan0 -c/tmp/wpa.conf
$ udhcpc -b -i wlan0 		PASS Verify with EWM-W163
16 BT Modules $ hciconfig hci0 up
$ bluetoothctl
$ discoverable on
$ pairable on
$ scan on
[NEW] FC:18:3C:8D:75:F4 myphone
$ scan off
$ pair FC:18:3C:8D:75:F4
$ connect FC:18:3C:8D:75:F4 		PASS Verify with EWM-W163 and AW-NB136NF 
17 Ethernet (Giga) Lan 1 1. Check IP & DHCP
2. Throughput
$ iperf3 -c 192.168.0.2 -t 60 -i 10 		AR8035 PASS
(Giga) Lan 2 AR8035 PASS
18 LED N/A LED Status: Detect gpio signal
LED ON: echo 255 > /sys/class/leds/user/brightness
LED OFF: echo 0 > /sys/class/leds/user/brightness 		PASS
19 USB USB Port 1 USB disk write/read/verify pattern EXTENSION I/O A PASS
USB Port 2 EXTENSION I/O A PASS
USB Port 3 EXTENSION I/O A PASS
USB Port 5 USB 3.0 Type A PASS
USB Port 6 USB 2.0 Type A PASS
USB Port 7 M.2 PASS lsusb (EWM-163)
USB Port 8 MINI CARD PASS lsusb (AirPrime MC8090)
20 USB OTG USB OTG 1. Host: USB disk write/read/verify pattern
2. Client: PC/NB can detect the device 		USB0 (USB_OTG1) N/A
21 HDMI HDMI 1.4 Display to HDMI screen PASS
22 VGA N/A Display to VGA screen N/A
23 LVDS LVDS 0 Display to 1st LVDS screen uboot: setenv fdt_file imx8mp-rsb3720-a1-lvds0-auo.dtb; boot PASS Verify with G070VW01
LVDS 1 Display to 2st LVDS screen uboot: setenv fdt_file imx8mp-rsb3720-a1-lvds1-auo.dtb; boot PASS Verify with G070VW01
Dual Channel(LVDS0+LVDS1) Modify DTS for dual channel LVDS uboot: setenv fdt_file imx8mp-rsb3720-a1-lvds-dual.dtb; boot PASS Verify with G215HVN01.0
24 MIPI DSI DSI 1 MIPI DSI to HDMI Bridge uboot: setenv fdt_file imx8mp-rsb3720-a1-adv7535.dtb; boot PASS Verify with MIPI to HDMI bridge: adv7535
MIPI DSI Panel uboot: setenv fdt_file imx8mp-rsb3720-a1-auog101uan02.dtb; boot PASS Verify with MIPI DSI Panel: auog101uan02
N/A N/A
25 Multi-Display 2 displays All display interfaces should work at the same time PASS
26 I2C I2C 0 1. Support function from I2C
2. Write/Read/Verify eeprom Hi/Low byte 		CODEC: 0x0A
PMIC: 0x25
WDT MCU: 0x29
TPM: 0x2E
RTC: 0x30-0x37
M.2:
LVDS: 0x50-0x57
IO_EXP: 0x70-0x71
0x70-
gpio 496: UART3_MODE0
gpio 497: UART3_MODE1
gpio 498: UART3_SLEW
gpio 499: UART3_TERM
gpio 501: GPIO2
gpio 503: GPIO4
0x71-
gpio 504: GPIO5
gpio 505: GPIO6
gpio 506: GPIO7
gpio 507: GPIO8
gpio 508: GPIO9
gpio 509: GPIO10
gpio 510: GPIO11
gpio 511: GPIO12 		PASS
I2C 1 CSI1: 0x3c - ov5640 camera PASS
I2C 2 CSI2: 0x3c - ov5640 camera PASS
I2C 3 UIO Board: 0x50: EEPROM
/sys/bus/i2c/devices/3-0050/eeprom 		PASS
I2C 4 HDMI EDID: 0x50: EEPROM PASS
27 I2C Switch N/A 1. Support function from I2C
2. Write/Read/Verify eeprom Hi/Low byte 		N/A
N/A N/A
N/A N/A
N/A N/A
28 RTC RTC external $ date MMDDhhmm[[CC]YY][.ss]
$ hwclock -w
$ ntpdate tw.pool.ntp.org 		SEIKO S-35390A PASS
RTC internal imx_sc_rtc N/A
29 Audio HDMI Audio $ aplay -D plughw:1,0 Advantech.wav Errata
Line-Out/Speaker $ aplay -D plughw:0,0 Advantech.wav PASS
Mic-In $ arecord -D plughw:0,0 -r 16000 -f S16_LE ./f-16000.wav PASS
30 SPDIF N/A Audio output N/A
31 WATCHDOG External Watchdog $ echo 1 > /dev/watchdog
$ /unit_tests/Watchdog/wdt_driver_test.out 1 2 0
==> System will reboot after 1 sec 		TI_MSP430G2202IRSA16R PASS
32 Camera MIPI CSI0 Preview:
$gst-launch-1.0 v4l2src device=/dev/video0! 'video/x-raw,width=640,height=480' ! autovideosink
Snapshot:
$gst-launch-1.0 v4l2src device=/dev/video0num-buffers=2 ! jpegenc ! multifilesink location=sample.jpeg max-files=1 		OV5640 Camera - 2 lane PASS
Preview:
$gst-launch-1.0 -v v4l2src device=/dev/video0! "video/x-raw,format=YUY2,width=1920,height=1080" ! queue ! imxvideoconvert_g2d !  waylandsink
Snapshot:
gst-launch-1.0 v4l2src num-buffers=1 device=/dev/video0! video/x-raw,width=1920,height=1080 ! jpegenc ! filesink location=sample.jpeg 		Basler Camera - 4 lane
uboot: setenv fdt_file imx8mp-rsb3720-a1-basler.dtb; boot
Need using the DSI to HDMI in 5.4.24 BSP 		PASS
MIPI CSI1 Preview:
$gst-launch-1.0 v4l2src device=/dev/video1! 'video/x-raw,width=640,height=480' ! autovideosink
Snapshot:
$gst-launch-1.0 v4l2src device=/dev/video1num-buffers=2 ! jpegenc ! multifilesink location=sample.jpeg max-files=1 		OV5640 Camera - 2 lane PASS
33 Keypad N/A 1. Detect 16 buttons
2. Verify each button event 		N/A
34 Key & Button N/A Power on/off test N/A
N/A $ evtest N/A
N/A $ evtest N/A
N/A Detect gpio signal key_event N/A
N/A Detect gpio signal N/A
Reset Button Reset system PASS
N/A Close backlight N/A
35 Multi-Boot Selection Boot Select Switch EMMC or Carrier SD or Carrier SPI PASS SD: OK
EMMC: OK
QSPI: OK
36 Recovery & Rescue Downalod via USB OTG $ uuu -b emmc_all bootloader rootfs.sdcard N/A
37 MCU N/A MCU integration N/A
38 PMIC Vendor Solution Power sequence or GPIO or other configurations N/A
39 Battery & Charging Battery EC $ cat /sys/class/power_supply/bms/uevent N/A
40 CAN Bus CAN 1 $ ip link set can0 up type can bitrate 125000
$ ifconfig can0 up
$ ip link set can1 up type can bitrate 125000
$ ifconfig can1 up

$ candump can0 &
$ cansend can1 1F334455#1122334455667788 		UIO-4034 CAN Pin 2 and Pin 7 connect to RSB-3720 COM1 Pin 8 and Pin 2 PASS
CAN 2 PASS
41 SATA N/A Mount and read/write/verify data under kernel N/A
42 System Bus N/A Test two uart ports N/A
43 IR Controller N/A Verify each button event N/A
44 GPS N/A Set correct date/time before test

sudo apt-get install gpsd-clients gnss-gpsd

$ systemctl start gpsd.socket
$ systemctl start gpsd
$ systemctl start qdsp-start
$ systemctl start gnss-gpsd
$ gpsmon

If you have DNS problem, you can try commands below.
echo "nameserver 8.8.8.8" | sudo tee /etc/resolv.conf > /dev/null
sudo apt-get updat 		To stop GPS hardware, follow the instructions:
1. close gpsmon
2. systemctl stop gnss-gpsd

To restart GPS hardware, follow the instructions:
1. systemctl start gnss-gpsd
2. close gpsmon 		N/A
45 Warm Reboot Warm Reboot Software reboot PASS
46 Security Boot NXP HAB Depends on platforms N/A
47 TPM Trust Platform Module tpm_test.bin PASS
Retrieved from "https://ess-wiki.advantech.com.tw/wiki/index.php?title=Test_Report_vA0076&oldid=19880"