Difference between revisions of "UIO-4030"

Latest revision as of 09:56, 1 November 2024

General Specificationn

1 x 2 wires RS-232
1 xRS-485
GPIO: 4 DIs and 4 DOs (2.5~24V)
Dimension: 146 x 31 x 22 mm

Environment Specification

Weight: 180g
Operating Humidity: 5 ~ 95% relative humidity, non-condensing
Operating Temperature: -40 ~ 85 *C
Storage Temperature: -40 ~ 85 *c and 60 *c @95% RH non-condensing

Ordering Information

P/N	Description
UIO-4030	1x RS232, 4x Dis, 4x DOs, 1x RS-485

Find Other Products

[edit]

RSB-3430
RSB-3720
RSB-3730
RSB-3710
RSB-3810

Note: RS-232: /dev/ttymxc2
GPIO : need to connect loopback.
RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232

$ stty -F /dev/ttymxc2 -echo -onlcr 115200 crtscts
$ cat /dev/ttymxc2 &
$ echo "Serial Port Test" > /dev/ttymxc2

RS485

Test RS-485 with Adam-4520.

$ stty -F /dev/ttyUSB0 115200
$ echo "Serial Test" > /dev/ttyUSB0

GPIO

[EXTENSION I/O B]
pin#5: gpio 121, pin#6: gpio 122
pin#7: gpio 123, pin#8: gpio 124
pin#9: gpio 125, pin#10: gpio 126
pin#11: gpio 127, pin#12: 133

RS-232(COM3):

# stty -F /dev/ttymxc1 -echo -onlcr 115200
# cat /dev/ttymxc1 &
# echo "Serial Port Test" /dev/ttymxc1

RS-485

Note:

Adam-4520
Data- : Pin1
Data+ : Pin2
Remember to set up RS-485 before test.

# stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke
# cat /dev/ttyUSB0 &
# echo "Serial Test" > /dev/ttyUSB0

GPIO

Note:
input pin#5: gpio 504(DB9-1 DI1#)
output pin#6: gpio 505(DB9-6 DO1#)
input pin#7: gpio 506(DB9-2 DI2#)
output pin#8: gpio 507(DB9-7 DO2#)
input pin#9: gpio 508(DB9-3 DI3#)
output pin#10: gpio 509(DB9-8 DO3#)
input pin#11: gpio 139(DB9-4 DI4#)
output pin#12: gpio 138(DB9-9 DO4#)

Short DI1# to DO1#

# echo 504 > /sys/class/gpio/export
# echo 505 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio2/direction
# echo in > /sys/class/gpio/gpio1/direction
# cat /sys/class/gpio/gpio1/value
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value

Short DI2# to DO2#

# echo 506 > /sys/class/gpio/export
# echo 507 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio4/direction
# echo in > /sys/class/gpio/gpio3/direction
# cat /sys/class/gpio/gpio3/value
# echo 1 > /sys/class/gpio/gpio4/value
# cat /sys/class/gpio/gpio3/value

Short DI3# to DO3#

# echo 508 > /sys/class/gpio/export
# echo 509 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio6/direction
# echo in > /sys/class/gpio/gpio5/direction
# cat /sys/class/gpio/gpio5/value
# echo 1 > /sys/class/gpio/gpio6/value
# cat /sys/class/gpio/gpio5/value

Short DI4# to DO4#

# echo 139 > /sys/class/gpio/export
# echo 138 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio8/direction
# echo in > /sys/class/gpio/gpio7/direction
# cat /sys/class/gpio/gpio7/value
# echo 1 > /sys/class/gpio/gpio8/value
# cat /sys/class/gpio/gpio7/value

Note: RS-232: /dev/ttymxc2
GPIO : need to connect loopback.
RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232

U-boot Setting

u-boot=> setenv uart_mode 2:0
u-boot=> saveenv
u-boot => reset

$ stty -F /dev/ttymxc0 -echo -onlcr 115200
$ cat /dev/ttymxc0 &
$ echo "Serial Port Test" > /dev/ttymxc0

RS485

U-boot Setting

u-boot=> setenv uart_mode 2:0
u-boot=> saveenv
u-boot => reset

Test RS-485

$ stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke
$ cat /dev/ttyUSB0 &
$ echo "Serial Test" > /dev/ttyUSB0

GPIO

GPIO pin	Number
GPIO1	150
GPIO2	151
GPIO3	152
GPIO4	153
GPIO5	85
GPIO6	141
GPIO7	506
GPIO8	140
GPIO9	511
GPIO10	138
GPIO11	0
GPIO12	97
GPIO_Select	LOW (83)

Short GPIO pin1(in) 151 & pin6(out) 141
# echo 150 > /sys/class/gpio/export
# echo 141 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio1/direction
# echo out > /sys/class/gpio/gpio2/direction
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value
0
# cat /sys/class/gpio/gpio2/value
1

Short GPIO pin2 (in) 151 & pin7 (out) 506
# echo 151 > /sys/class/gpio/export
# echo 506 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio3/direction
# echo out > /sys/class/gpio/gpio4/direction
# echo 1 > /sys/class/gpio/gpio4/value
# cat /sys/class/gpio/gpio3/value
0

Short GPIO pin3(in) 152  & pin 8 (out) 140
# echo 152 > /sys/class/gpio/export
# echo 140 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio5/direction
# echo out > /sys/class/gpio/gpio6/direction
# echo 1 > /sys/class/gpio/gpio6/value
# cat /sys/class/gpio/gpio6/value
1
# cat /sys/class/gpio/gpio5/value
0

Short GPIO pin4 (in) 153 & pin9 (out) 511
# echo 153 > /sys/class/gpio/export
# echo 511 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio1/direction
# echo out > /sys/class/gpio/gpio2/direction
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value
0

Note: RS-232: /dev/ttyS0
GPIO : need to connect loopback.
RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232

$ stty -F /dev/ttyS0 -echo -onlcr 115200 crtscts
$ cat /dev/ttyS0 &
$ echo "Serial Port Test" > /dev/ttyS0

RS485

Test RS-485 with Adam-4520.

$ stty -F /dev/ttyUSB0 115200
$ echo "Serial Test" > /dev/ttyUSB0

GPIO

UIO-4030使用方法(UIO-4030 Testing Method):[edit]

1	UART(COM_3)	# stty -F /dev/ttyS3 -echo -onlcr 921600 raw # cat /dev/ttyS3 & # echo "Serial Port Test" > /dev/ttyS3 or #microcom -s 921600 -X /dev/ttyS3
2	GPIO	4 DI & 4 DO Pins (UIO Extension_UIO2) input pin#5: gpio 317 output pin#6: gpio 318 input pin#7: gpio 319 output pin#8: gpio 320 input pin#9: gpio 321 output pin#10: gpio 322 input pin#11: gpio 323 output pin#12: gpio 324 (Note: gpio 323 & gpio 324 need to set the gpio 345 to high)
3	RS-485(COM_4)	Test RS-485 with Adam-4520. Adam-4520 Pin Data- and Pin Data+ connect to UIO-4030 COM_4 Pin 1 and Pin 2. # stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl - imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke # cat /dev/ttyUSB0 & # echo "Serial Test" > /dev/ttyUSB0
4	EEPROM	# echo -n $'\x06\x05\x04\x03\x02\x01' > /data/test1 # dd if=/data/test1 of=/sys/bus/i2c/devices/3-0050/eeprom # dd if=/sys/bus/i2c/devices/3-0050/eeprom of=/data/test2 conv=fsync

@@ Line 82: / Line 82: @@
 '''GPIO'''
-Note:<br/> input pin#5: gpio 504(DB9-1)<br/> output pin#6: gpio 505(DB9-6)<br/> input pin#7: gpio 506(DB9-2)<br/> output pin#8: gpio 507(DB9-7)<br/> input pin#9: gpio 508(DB9-3)<br/> output pin#10: gpio 509(DB9-8)<br/> input pin#11: gpio 139(DB9-4)<br/> output pin#12: gpio 138(DB9-9)
+Note:<br/> input pin#5:&nbsp; &nbsp; &nbsp; &nbsp; gpio 504(DB9-1 DI1#)<br/> output pin#6:&nbsp; &nbsp; &nbsp; gpio 505(DB9-6 DO1#)<br/> input pin#7:&nbsp; &nbsp; &nbsp; &nbsp; gpio 506(DB9-2 DI2#)<br/> output pin#8:&nbsp; &nbsp; &nbsp; gpio 507(DB9-7 DO2#)<br/> input pin#9:&nbsp; &nbsp; &nbsp; &nbsp; gpio 508(DB9-3 DI3#)<br/> output pin#10:&nbsp; &nbsp; gpio 509(DB9-8 DO3#)<br/> input pin#11:&nbsp; &nbsp; &nbsp; gpio 139(DB9-4 DI4#)<br/> output pin#12:&nbsp; &nbsp; gpio 138(DB9-9 DO4#)
+Short DI1# to DO1#
 <pre># echo 504 > /sys/class/gpio/export
 # echo 505 > /sys/class/gpio/export
@@ Line 93: / Line 95: @@
 [[File:RSB-3720 GPIOp1.png|RTENOTITLE]]
+Short DI2# to DO2#
 <pre># echo 506 > /sys/class/gpio/export
 # echo 507 > /sys/class/gpio/export
@@ Line 102: / Line 106: @@
 [[File:RSB-3720 GPIOp2.png|RTENOTITLE]]
+Short DI3# to DO3#
 <pre># echo 508 > /sys/class/gpio/export
 # echo 509 > /sys/class/gpio/export
@@ Line 112: / Line 118: @@
 [[File:RSB-3720 GPIOp3.png|RTENOTITLE]]
+Short DI4# to DO4#
 <pre># echo 139 > /sys/class/gpio/export
 # echo 138 > /sys/class/gpio/export
@@ Line 252: / Line 260: @@
 &nbsp;
-== <br/> <br/> <br/> <!--[[File:UIO-4030 photo3 2021-10-27 141714.jpg|RTENOTITLE]]--> ==
+= RSB-3710 =
+'''&nbsp;Note: RS-232: /dev/ttyS0&nbsp;<br/> &nbsp;GPIO&nbsp;: need to connect loopback.<br/> &nbsp;RS-485: pin1 data- & pin2 data+ (ttyUSB0)'''
+'''RS-232'''
+<pre>$ stty -F /dev/ttyS0 -echo -onlcr 115200 crtscts
+$ cat /dev/ttyS0 &
+$ echo "Serial Port Test" > /dev/ttyS0</pre>
+'''RS485&nbsp;<br/> &nbsp;&nbsp; &nbsp;<br/> Test RS-485 with Adam-4520.'''
+<pre>$ stty -F /dev/ttyUSB0 115200
+$ echo "Serial Test" > /dev/ttyUSB0</pre>
+'''GPIO&nbsp;'''
+'''[[File:RSB-3710 GPIO define 2022-01-20 142613.jpg|RTENOTITLE]]'''
+[[File:RSB-3710 gpio1 2022-01-20 142757.jpg|RTENOTITLE]]
+[[File:RSB-3710 gpio2 2022-01-20 142824.jpg|RTENOTITLE]]
+&nbsp;
+&nbsp;
+= RSB-3810 =
+=== '''UIO-4030使用方法(UIO-4030 Testing Method):'''[[https://ess-wiki.advantech.com.tw/wiki/index.php?title=RSB-3810_user_guide_Ubuntu22.04&action=edit&section=27 edit]] ===
+{| border="1" cellpadding="1" cellspacing="1"
+|-
+| 1
+| UART(COM_3)
+| # stty -F /dev/ttyS3 -echo -onlcr 921600 raw<br/> # cat /dev/ttyS3 &<br/> # echo "Serial Port Test" > /dev/ttyS3<br/> or<br/> #microcom -s 921600 -X /dev/ttyS3
+|-
+| 2
+| GPIO
+|
+DI & 4 DO Pins (UIO Extension_UIO2)<br/> input pin#5: gpio 317&nbsp;<br/> output pin#6: gpio 318&nbsp;<br/> input pin#7: gpio 319<br/> output pin#8: gpio 320<br/> input pin#9: gpio 321<br/> output pin#10: gpio 322<br/> input pin#11: gpio 323<br/> output pin#12: gpio 324
+(Note: gpio 323 & gpio 324 need to set the gpio 345 to high)
+|-
+| 3
+| RS-485(COM_4)
+| Test RS-485 with Adam-4520. Adam-4520 Pin Data- and Pin<br/> Data+ connect to UIO-4030 COM_4 Pin 1 and Pin 2.<br/> # stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl - imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke<br/> # cat /dev/ttyUSB0 &<br/> # echo "Serial Test" > /dev/ttyUSB0
+|-
+| 4
+| EEPROM
+| # echo -n $'\x06\x05\x04\x03\x02\x01' > /data/test1<br/> # dd if=/data/test1 of=/sys/bus/i2c/devices/3-0050/eeprom # dd if=/sys/bus/i2c/devices/3-0050/eeprom of=/data/test2 conv=fsync
+|}
-<headertabs></headertabs>
+== <headertabs></headertabs> ==

Difference between revisions of "UIO-4030"

Latest revision as of 09:56, 1 November 2024

UIO-4030使用方法(UIO-4030 Testing Method):[edit]

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools