Difference between revisions of "Edge Sense LoRa Module Firmware Upgrade"
(.) |
(.) |
||
| (12 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
= Requirements = | = Requirements = | ||
| − | + | == ST-LINK/V2 == | |
| − | + | <span style="font-size:larger;">The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.</span> | |
| − | = | + | <span style="font-size:larger;">[[File:ST-Linkv2.jpg|RTENOTITLE]]</span> |
| − | = | + | <span style="font-size:larger;">[https://www.st.com/en/development-tools/st-link-v2.html https://www.st.com/en/development-tools/st-link-v2.html]</span> |
| − | = | + | == STM32 ST-Link Utility == |
| − | = | + | <span style="font-size:larger;">STM32 ST-LINK Utility (STSW-LINK004) is a full-featured software interface for programming STM32 microcontrollers.</span> |
| − | = | + | <span style="font-size:larger;">This utility is available at [http://www.st.com/en/development-tools/stsw-link004.html http://www.st.com/en/development-tools/stsw-link004.html]</span> |
| − | *<span style="font-size:larger;"> | + | = Module = |
| + | |||
| + | == RYLRxxP == | ||
| + | |||
| + | <span style="font-size:larger;">Step1 - Insert cable to LoRa module</span> | ||
| + | |||
| + | <span style="font-size:larger;">Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxxP (ex: RYLRxx<span style="color:#FF0000;">P</span>_V0.2.9.hex) to program flash.</span> | ||
| + | |||
| + | == RYLRxx6 == | ||
| + | |||
| + | [[File:RYLRxx6.jpg|RTENOTITLE]] | ||
| + | |||
| + | <span style="font-size:larger;">Step1 - Insert cable to LoRa module</span> | ||
| + | |||
| + | <span style="font-size:larger;">[[File:RYLRxx6 connect.jpg|RTENOTITLE]]</span> | ||
| + | |||
| + | <span style="font-size:larger;">Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxx6 (ex: RYLRxx<span style="color:#FF0000;">6</span>_V0.2.10.hex) to program flash.</span> | ||
| + | |||
| + | == RYLRxxE == | ||
| + | |||
| + | <span style="font-size:larger;">Step1 - Insert cable to LoRa module</span> | ||
| + | |||
| + | <span style="font-size:larger;">[[File:RYLRxxE connect1.jpg|RTENOTITLE]]</span> | ||
| + | |||
| + | <span style="font-size:larger;">[[File:RYLRxxE connect2.jpg|RTENOTITLE]]</span> | ||
| + | |||
| + | <span style="font-size:larger;">Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxxE (ex: RYLRxx<span style="color:#FF0000;">E</span>_V0.1.16.hex) to program flash.</span> | ||
| + | |||
| + | == RYLRxx2 == | ||
| + | |||
| + | <span style="font-size:larger;">Step1 - Insert cable to LoRa module</span> | ||
| + | |||
| + | <span style="font-size:larger;">Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxx2 (ex: RYLRxx<span style="color:#FF0000;">2</span>_V0.2.4.hex) to program flash.</span> | ||
| + | |||
| + | = Programming via STM32 ST-Link Utility = | ||
| + | |||
| + | <span style="font-size:larger;">Step1 - Connect device</span> | ||
| + | |||
| + | <span style="font-size:larger;">Step2 - Select hex file</span> | ||
| + | |||
| + | [[File:ST-Link Utility program1.png|RTENOTITLE]] | ||
| + | |||
| + | <span style="font-size:larger;">Step3 - click "Program verify" button</span> | ||
| + | |||
| + | [[File:ST-Link Utility program2.png|RTENOTITLE]] | ||
| + | |||
| + | <span style="font-size:larger;">Step4 - Click "Start"</span> | ||
| + | |||
| + | [[File:ST-Link Utility program3.png|RTENOTITLE]] | ||
| + | |||
| + | = Reference = | ||
| + | |||
| + | *<span style="font-size:larger;">Lora程式更新與燒錄法 V0.93.pdf</span> | ||
| + | [[Category:Pages with broken file links]] | ||
Latest revision as of 08:29, 13 December 2018
Contents
Requirements
ST-LINK/V2
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.
https://www.st.com/en/development-tools/st-link-v2.html
STM32 ST-Link Utility
STM32 ST-LINK Utility (STSW-LINK004) is a full-featured software interface for programming STM32 microcontrollers.
This utility is available at http://www.st.com/en/development-tools/stsw-link004.html
Module
RYLRxxP
Step1 - Insert cable to LoRa module
Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxxP (ex: RYLRxxP_V0.2.9.hex) to program flash.
RYLRxx6
Step1 - Insert cable to LoRa module
Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxx6 (ex: RYLRxx6_V0.2.10.hex) to program flash.
RYLRxxE
Step1 - Insert cable to LoRa module
Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxxE (ex: RYLRxxE_V0.1.16.hex) to program flash.
RYLRxx2
Step1 - Insert cable to LoRa module
Step 2 - Open STM32 ST-LINK Utility and select hex file for RYLRxx2 (ex: RYLRxx2_V0.2.4.hex) to program flash.
Programming via STM32 ST-Link Utility
Step1 - Connect device
Step2 - Select hex file
Step3 - click "Program verify" button
Step4 - Click "Start"
Reference
- Lora程式更新與燒錄法 V0.93.pdf