UIO-4030

From ESS-WIKI
Revision as of 02:34, 25 March 2024 by Phill.liu (talk | contribs)
Jump to: navigation, search
RTENOTITLE

General Specificationn

  • 1 x 2 wires RS-232
  • 1 xRS-485
  • GPIO: 4 DIs and 4 DOs (2.5~24V)
  • Dimension: 146 x 31 x 22 mm

Environment Specification

  • Weight: 180g
  • Operating Humidity: 5 ~ 95% relative humidity, non-condensing
  • Operating Temperature: -40 ~ 85 *C
  • Storage Temperature: -40 ~ 85 *c and 60 *c @95% RH non-condensing

 

Ordering Information
P/N Description
UIO-4030 1x RS232, 4x Dis, 4x DOs, 1x RS-485

Find Other Products

[edit]

 Note: RS-232: /dev/ttymxc2 
 GPIO : need to connect loopback.
 RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232 

$ stty -F /dev/ttymxc2 -echo -onlcr 115200 crtscts
$ cat /dev/ttymxc2 &
$ echo "Serial Port Test" > /dev/ttymxc2

RS485 
    
Test RS-485 with Adam-4520. 

$ stty -F /dev/ttyUSB0 115200
$ echo "Serial Test" > /dev/ttyUSB0

GPIO  

[EXTENSION I/O B]
pin#5: gpio 121, pin#6: gpio 122
pin#7: gpio 123, pin#8: gpio 124
pin#9: gpio 125, pin#10: gpio 126
pin#11: gpio 127, pin#12: 133

RS-232(COM3): 

# stty -F /dev/ttymxc1 -echo -onlcr 115200
# cat /dev/ttymxc1 &
# echo "Serial Port Test" /dev/ttymxc1

RS-485

Note: 

Adam-4520
Data- : Pin1
Data+ : Pin2
Remember to set up RS-485 before test. 

# stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke
# cat /dev/ttyUSB0 &
# echo "Serial Test" > /dev/ttyUSB0

GPIO

Note:
input pin#5: gpio 504(DB9-1)
output pin#6: gpio 505(DB9-6)
input pin#7: gpio 506(DB9-2)
output pin#8: gpio 507(DB9-7)
input pin#9: gpio 508(DB9-3)
output pin#10: gpio 509(DB9-8)
input pin#11: gpio 139(DB9-4)
output pin#12: gpio 138(DB9-9) 

# echo 504 > /sys/class/gpio/export
# echo 505 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio2/direction
# echo in > /sys/class/gpio/gpio1/direction
# cat /sys/class/gpio/gpio1/value
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value

RTENOTITLE 

# echo 506 > /sys/class/gpio/export
# echo 507 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio4/direction
# echo in > /sys/class/gpio/gpio3/direction
# cat /sys/class/gpio/gpio3/value
# echo 1 > /sys/class/gpio/gpio4/value
# cat /sys/class/gpio/gpio3/value

RTENOTITLE 

# echo 508 > /sys/class/gpio/export
# echo 509 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio6/direction
# echo in > /sys/class/gpio/gpio5/direction
# cat /sys/class/gpio/gpio5/value
# echo 1 > /sys/class/gpio/gpio6/value
# cat /sys/class/gpio/gpio5/value

RTENOTITLE 

# echo 139 > /sys/class/gpio/export
# echo 138 > /sys/class/gpio/export
# echo out > /sys/class/gpio/gpio8/direction
# echo in > /sys/class/gpio/gpio7/direction
# cat /sys/class/gpio/gpio7/value
# echo 1 > /sys/class/gpio/gpio8/value
# cat /sys/class/gpio/gpio7/value

RTENOTITLE

 Note: RS-232: /dev/ttymxc2 
 GPIO : need to connect loopback.
 RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232

U-boot Setting 

u-boot=> setenv uart_mode 2:0
u-boot=> saveenv
u-boot => reset

RTENOTITLE 

$ stty -F /dev/ttymxc0 -echo -onlcr 115200
$ cat /dev/ttymxc0 &
$ echo "Serial Port Test" > /dev/ttymxc0

RTENOTITLE

 

RS485 

U-boot Setting 

u-boot=> setenv uart_mode 2:0
u-boot=> saveenv
u-boot => reset

RTENOTITLE

    
Test RS-485  

$ stty -F /dev/ttyUSB0 speed 115200 ignbrk -brkint -icrnl -imaxbel -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke
$ cat /dev/ttyUSB0 &
$ echo "Serial Test" > /dev/ttyUSB0

RTENOTITLE

GPIO 

GPIO pin Number
GPIO1 150
GPIO2 151
GPIO3 152
GPIO4 153
GPIO5 85
GPIO6 141
GPIO7 506
GPIO8 140
GPIO9 511
GPIO10 138
GPIO11 0
GPIO12 97
GPIO_Select LOW (83) 
Short GPIO pin1(in) 151 & pin6(out) 141
# echo 150 > /sys/class/gpio/export
# echo 141 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio1/direction
# echo out > /sys/class/gpio/gpio2/direction
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value
0
# cat /sys/class/gpio/gpio2/value
1

RTENOTITLE 

Short GPIO pin2 (in) 151 & pin7 (out) 506
# echo 151 > /sys/class/gpio/export
# echo 506 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio3/direction
# echo out > /sys/class/gpio/gpio4/direction
# echo 1 > /sys/class/gpio/gpio4/value
# cat /sys/class/gpio/gpio3/value
0

Short GPIO pin3(in) 152  & pin 8 (out) 140
# echo 152 > /sys/class/gpio/export
# echo 140 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio5/direction
# echo out > /sys/class/gpio/gpio6/direction
# echo 1 > /sys/class/gpio/gpio6/value
# cat /sys/class/gpio/gpio6/value
1
# cat /sys/class/gpio/gpio5/value
0

  

Short GPIO pin4 (in) 153 & pin9 (out) 511
# echo 153 > /sys/class/gpio/export
# echo 511 > /sys/class/gpio/export
# echo in > /sys/class/gpio/gpio1/direction
# echo out > /sys/class/gpio/gpio2/direction
# echo 1 > /sys/class/gpio/gpio2/value
# cat /sys/class/gpio/gpio1/value
0

 

 Note: RS-232: /dev/ttyS0 
 GPIO : need to connect loopback.
 RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232 

$ stty -F /dev/ttyS0 -echo -onlcr 115200 crtscts
$ cat /dev/ttyS0 &
$ echo "Serial Port Test" > /dev/ttyS0

RS485 
    
Test RS-485 with Adam-4520. 

$ stty -F /dev/ttyUSB0 115200
$ echo "Serial Test" > /dev/ttyUSB0

GPIO 

RTENOTITLE

RTENOTITLE

RTENOTITLE


 

 Note: RS-232: /dev/ttyS0 
 GPIO : need to connect loopback.
 RS-485: pin1 data- & pin2 data+ (ttyUSB0)

RS-232 

$ stty -F /dev/ttyS0 -echo -onlcr 115200 crtscts
$ cat /dev/ttyS0 &
$ echo "Serial Port Test" > /dev/ttyS0

RS485 
    
Test RS-485 with Adam-4520. 

$ stty -F /dev/ttyUSB0 115200
$ echo "Serial Test" > /dev/ttyUSB0

GPIO 

RTENOTITLE

RTENOTITLE

RTENOTITLE

Retrieved from "https://ess-wiki.advantech.com.tw/wiki/index.php?title=UIO-4030&oldid=34640"