Difference between revisions of "WISE-ED22 User Manual"
Erick.huang (talk | contribs) |
|||
| (12 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
= ED22 Functions = | = ED22 Functions = | ||
| − | There are | + | There are two interfaces that ED22 board provides. Both are '''drag-n-drop programming''' and '''a serial port'''. In addition ED22 board firmware can be updated using the drag-n-drop programming interface of the bootloader. |
= H/W Setup = | = H/W Setup = | ||
| Line 31: | Line 31: | ||
When you get a new WISE-ED22, you must perform the following steps to updated it's FW. Make WISE-ED22 suitable for your product. | When you get a new WISE-ED22, you must perform the following steps to updated it's FW. Make WISE-ED22 suitable for your product. | ||
| − | Step1: | + | Step1: Connect the WISE-ED22 to PC using micro-USB cable. Please hold down the button SW1 and press the button RST1 once, then release the button SW1 and you will see the CRP DISABLD |
| + | |||
| + | [[File:ED22 FW update 1.png|168x172px|ED22 FW update 1.png]] | ||
Step2: Open the "CRP Disabled" drive, and delete the file called "firmware.bin" | Step2: Open the "CRP Disabled" drive, and delete the file called "firmware.bin" | ||
| − | Step3: | + | [[File:ED22 FW update 2 v1.png|456x288px|ED22 FW update 2 v1.png]] |
| + | |||
| + | Step3:Copy the WISE-ED22 FW that corresponding to target MCU onto the "CRP DISABLD" drive. | ||
| + | |||
| + | [[File:ED22-firmware-update-01.png|861x551px|ED22-firmware-update-01.png]] | ||
| − | + | Step4: Press ED22 board reset to restart, then you can see a disk drive called DAPLink. | |
| − | WISE-ED22 FW | + | [[File:ED22 FW update 4.png|210x192px|ED22 FW update 4.png]] |
| + | |||
| + | WISE-ED22 FW binary files (you will see the binary file after uncompressed the *.zip) : | ||
1. [[Media:Lpc11u35_stm32L443_v1.3.zip|STM32L443]]: WISE-1510/WISE-1511/WISE-1540 | 1. [[Media:Lpc11u35_stm32L443_v1.3.zip|STM32L443]]: WISE-1510/WISE-1511/WISE-1540 | ||
| Line 45: | Line 53: | ||
2. [[Media:Lpc11u35_stm32F412_v1.3.zip|STM32F412]]: WISE-1530/EPD-132 | 2. [[Media:Lpc11u35_stm32F412_v1.3.zip|STM32F412]]: WISE-1530/EPD-132 | ||
| − | 3. [[Media: | + | 3. [[Media:Lpc11u35_mtb_wise1570_if_crc_v252_intrpt_msk_revt.zip|STM32L486]]: WISE-1570 |
= Using ED22 = | = Using ED22 = | ||
| Line 72: | Line 80: | ||
*9600 | *9600 | ||
*115200 | *115200 | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 06:17, 18 March 2021
Contents
ED22 Functions
There are two interfaces that ED22 board provides. Both are drag-n-drop programming and a serial port. In addition ED22 board firmware can be updated using the drag-n-drop programming interface of the bootloader.
H/W Setup
ED22 Introduction
1. ED22 board reset button.
2. Target MCU(STM32L443/STM32F412/STM32F486) reset button.
3. Micro USB connector.
4.10pin FFC connector.
Connection with target board
Install Driver
ED22 Firmware Update
When you get a new WISE-ED22, you must perform the following steps to updated it's FW. Make WISE-ED22 suitable for your product.
Step1: Connect the WISE-ED22 to PC using micro-USB cable. Please hold down the button SW1 and press the button RST1 once, then release the button SW1 and you will see the CRP DISABLD
Step2: Open the "CRP Disabled" drive, and delete the file called "firmware.bin"
Step3:Copy the WISE-ED22 FW that corresponding to target MCU onto the "CRP DISABLD" drive.
Step4: Press ED22 board reset to restart, then you can see a disk drive called DAPLink.
WISE-ED22 FW binary files (you will see the binary file after uncompressed the *.zip) :
1. STM32L443: WISE-1510/WISE-1511/WISE-1540
2. STM32F412: WISE-1530/EPD-132
3. STM32L486: WISE-1570
Using ED22
Drag-n-drop Programming
To use the ED22, simply connect to your PC with a micro-USB cable, and to the WISE-15XX board using a 10 pin FFC cable. You can drag and drop binary images onto the DAPLink disk drive, which will then be programmed into the target system.If errors are encountered, a file called "fail.txt" will appear with details.
Note that the ED22 has to contain the correct firmware to enable drag and drop programming.
Supported file formats:
- Raw binary file
- Intel Hex
Serial Port
The serial port is connected directly to the target MCU allowing for bidirectional communication. It also allows the target to be reset by
sending a break command over the serial port.
Supported baud rates:
- 9600
- 115200