Difference between revisions of "WISE-ED22 User Manual"

From ESS-WIKI
Jump to: navigation, search
 
(84 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
= ED22  =
+
= ED22 Functions =
  
−
There are three interfaces that ED22 board provides. These are '''drag-n-drop programming''', '''a serial port''' and '''debugging''' support. In addition ED22 board firmware can be updated using the drag-n-drop programming interface of the bootloader.
+
There are two interfaces that ED22 board provides. Both are '''drag-n-drop programming''' and '''a serial port'''. In addition ED22 board firmware can be updated using the drag-n-drop programming interface of the bootloader.
  
−
== Drag-n-drop Programming ==
+
= H/W Setup =
 +
 
 +
== ED22 Introduction ==
 +
 
 +
       [[File:ED22 board v1.png|upright|ED22 board v1.png]] 
 +
 
 +
      1. ED22 board reset button.
 +
 
 +
      2. Target MCU(STM32L443/STM32F412/STM32F486) reset button.
 +
 
 +
      3. Micro USB connector.
 +
 
 +
      4.10pin FFC connector.
 +
 
 +
== Connection with target board ==
 +
 
 +
 [[File:ED22 to taget.png|305x266px|ED22 to taget.png]]   
 +
 
 +
 [[File:ED22 to DB1500.png|RTENOTITLE]]
 +
 
 +
= Install Driver =
 +
 
 +
[https://developer.mbed.org/media/downloads/drivers/mbedWinSerial_16466.exe Download latest driver]
 +
 
 +
= ED22 Firmware Update =
 +
 
 +
When you get a new WISE-ED22, you must perform the following steps to updated it's FW. Make WISE-ED22 suitable for your product.
 +
 
 +
Step1: Connect the WISE-ED22 to PC using micro-USB cable. Please hold down the button SW1 and press the button RST1 once, then release the button SW1 and you will  see the CRP DISABLD
 +
 
 +
        [[File:ED22 FW update 1.png|168x172px|ED22 FW update 1.png]]
 +
 
 +
Step2: Open the "CRP Disabled" drive, and delete the file called "firmware.bin"
 +
 
 +
        [[File:ED22 FW update 2 v1.png|456x288px|ED22 FW update 2 v1.png]]
 +
 
 +
Step3:Copy the WISE-ED22 FW that corresponding to target MCU onto the "CRP DISABLD" drive. 
 +
 
 +
        [[File:ED22-firmware-update-01.png|861x551px|ED22-firmware-update-01.png]]
 +
 
 +
Step4: Press ED22 board reset to restart, then you can see a disk drive called DAPLink.  
 +
 
 +
        [[File:ED22 FW update 4.png|210x192px|ED22 FW update 4.png]]
 +
 
 +
WISE-ED22 FW binary files (you will see the binary file after uncompressed the *.zip) :
  
−
Program the target microcontroller(STM32L443/STM32F412) by copying or saving a file in one of the supported formats to the ED22 drive. Upon completion the drive will re-mount. If a failure occurs then the file FAIL.TXT will appear on the drive containing information about the failure.
+
    1. [[Media:Lpc11u35_stm32L443_v1.3.zip|STM32L443]]: WISE-1510/WISE-1511/WISE-1540
  
−
Supported file formats:
+
    2. [[Media:Lpc11u35_stm32F412_v1.3.zip|STM32F412]]: WISE-1530/EPD-132
  
−
*Raw binary file
+
    3. [[Media:Lpc11u35_mtb_wise1570_if_crc_v252_intrpt_msk_revt.zip|STM32L486]]: WISE-1570
−
*Intel Hex
 
  
−
==  ==
+
= Using ED22 =
  
−
= H/W  =
+
== Drag-n-drop Programming ==
  
−
[[File:ED22 board v1.png|upright|ED22 board v1.png]]
+
To use the ED22, simply connect to your PC with a micro-USB cable, and to the WISE-15XX board using a 10 pin FFC cable. You can drag and drop binary images onto the DAPLink disk drive, which will then be programmed into the target system.If errors are encountered, a file called "fail.txt" will appear with details.
  
−
1: ED22 reset button
+
Note that the ED22 has to contain the correct firmware to enable drag and drop programming.
  
 +
[[File:WISE-ED22 DAPLink disk.png|RTENOTITLE]]
  
 +
Supported file formats:
  
−
= Reprogramming SWDAP =
+
*Raw binary file
 +
*Intel Hex
  
−
When a new SWDAP is plugged in to your machine, it will not contain valid any firmware, and so will appear as a disk drive called "CRP Disabled" as.
+
== Serial Port ==
  
−
To progam the SWDAP, follow these steps:
+
The serial port is connected directly to the target MCU allowing for bidirectional communication. It also allows the target to be reset by
  
−
*Open the drive, and delete the file called "firmware.bin"
+
sending a break command over the serial port.
−
*Download the required image from the table above (or built your own using [https://github.com/mbedmicro/DAPLink DAPLink project])
 
−
*Copy the .bin file onto the "CRP Disabled" drive.
 
−
**On Windows, replace firmware.bin with the above firmware
 
−
**On Linux/Mac, use command: '''dd if={new_firmware.bin} of={firmware.bin} conv=notrunc'''
 
−
*Unplug your SWDAP, and plug it back in
 
−
*It should now appear as a disk drive called DAPLink
 
  
−
You can re-program your SWDAP at any time by plugging it in with the button held down. This will cause it to appear as the "CRP Disabled" drive, at which point you can follow the steps above.
+
Supported baud rates:
  
−
=  =
+
*9600
 +
*115200

Latest revision as of 06:17, 18 March 2021

ED22 Functions

There are two interfaces that ED22 board provides. Both are drag-n-drop programming and a serial port. In addition ED22 board firmware can be updated using the drag-n-drop programming interface of the bootloader.

H/W Setup

ED22 Introduction

       ED22 board v1.png 

      1. ED22 board reset button.

      2. Target MCU(STM32L443/STM32F412/STM32F486) reset button.

      3. Micro USB connector.

      4.10pin FFC connector.

Connection with target board

 ED22 to taget.png   

 RTENOTITLE

Install Driver

Download latest driver

ED22 Firmware Update

When you get a new WISE-ED22, you must perform the following steps to updated it's FW. Make WISE-ED22 suitable for your product.

Step1: Connect the WISE-ED22 to PC using micro-USB cable. Please hold down the button SW1 and press the button RST1 once, then release the button SW1 and you will  see the CRP DISABLD

        ED22 FW update 1.png

Step2: Open the "CRP Disabled" drive, and delete the file called "firmware.bin"

        ED22 FW update 2 v1.png

Step3:Copy the WISE-ED22 FW that corresponding to target MCU onto the "CRP DISABLD" drive. 

        ED22-firmware-update-01.png

Step4: Press ED22 board reset to restart, then you can see a disk drive called DAPLink.  

        ED22 FW update 4.png

WISE-ED22 FW binary files (you will see the binary file after uncompressed the *.zip) :

    1. STM32L443: WISE-1510/WISE-1511/WISE-1540

    2. STM32F412: WISE-1530/EPD-132

    3. STM32L486: WISE-1570

Using ED22

Drag-n-drop Programming

To use the ED22, simply connect to your PC with a micro-USB cable, and to the WISE-15XX board using a 10 pin FFC cable. You can drag and drop binary images onto the DAPLink disk drive, which will then be programmed into the target system.If errors are encountered, a file called "fail.txt" will appear with details.

Note that the ED22 has to contain the correct firmware to enable drag and drop programming.

RTENOTITLE

Supported file formats:

  • Raw binary file
  • Intel Hex

Serial Port

The serial port is connected directly to the target MCU allowing for bidirectional communication. It also allows the target to be reset by

sending a break command over the serial port.

Supported baud rates:

  • 9600
  • 115200
Retrieved from "https://ess-wiki.advantech.com.tw/wiki/index.php?title=WISE-ED22_User_Manual&oldid=19978"