Introduction

This document is description about WISE-1540 software development kit (SDK). It includes source tree of SDK, development environment, flash programming…etc. There are some examples provided by WISE-1540 SDK the user can refer to it for how to do about connection to WISE-PaaS, communication between mote and gateway…etc., and also can refer to it for developing their application.

Glossary

Gateway

The gateway like WISE-3310 has connectivity with SmartMesh IP manager responsible for communication with WISE-1540.

Mote

The mote is WISE-1540 that has connectivity with SmartMesh IP mote responsible for communication with gateway.

WISE-1540 Software Development Kit (SDK)

Source Tree

The user can find source tree as below from xxx.

Directory	Description
doc/	Documents about WISE-1540 SDK.
inc/	Header files including examples, sensor driver and etc.
lib/	Library.
src/	Source files including examples, sensor driver and etc.

Setup Development Environment

Preparing for Hardware

The user needs to prepare for hardware as following:

For mote, WISE-1540, WISE-1500 and WISE-ED20 or WISE-ED22.
For gateway, WISE-3310.
PC running LINUX operating systems such as Ubuntu 16.04.1.

Please refer to the following steps for setup a WISE series of boards before using WISE-1540 SDK.

Step01: Please prepare boards as below.

①WISE-1540

②WISE-1500

③WISE-ED20

④SW2 on WISE-ED20

Please check pin1 and pin2 to “ON” as default.
Switch pin1 to “ON”: flash programming, “OFF”: boot from flash.

⑤CN2 on WISE-1500

Booting into the mode of network connection when both 3.3V and GPIO0 are opened.
Booting into the mode of console of API when both 3.3V and GPIO0 are shorted.

⑥SW3 on WISE-1500

Please check pin1 and pin2 to “OFF” as default.
Switch pin2 to decide whether running “backup to default” while device booting. “ON”: enabled, “OFF”: disabled.

⑦One reset button on WISE-1500 and the other on WISE-ED20

⑧Micro USB connector

Power supplies for UART3 debug port.

⑨Com port

No supported.

Setting for Connectivity

WISE-1540 is designed in connectivity for wireless IoT communication with Linear Dust SmartMesh IP wireless sensor networks. The Linear Dust networks support a self-forming and self-healing mesh network solution complaint to 6LoWPAN Internet Protocol (IP) and IEEE802.15.4e standard. Before using WISE-1540 SDK, the user needs to check or set some parameters through the console for API.

Console for API

Information and Parameters Setting

The user needs to double check connectivity setting the same as below table with SmartMesh IP networks before using WISE-1540 SDK:

Parameter	Expected Setting
Network ID	2001 (The same as manager on WISE-3310)
Join Key	4A4F494E414456414E54454348494F54 (The same as manager on WISE-3310)
Auto Join	On

ARM mbed

The ARM mbed is IoT device platform and it has a lot of resources for IoT development. We supported ARM mbed OS on WISE-1540 to make user easily to get started and obtain great benefit from ARM mbed.

mbed CLI

The mbed CLI is command-line tool. The user needs to setup CLI for WISE-1540 SDK. Please refer to below link for information about how to setup CLI.

mbed CLI

Flash Programming

For flash programming, the user can do it through WISE-ED22 or WISE-ED20 with different programming tool. Please refer to the following steps for flash programming.

Programming through WISE-ED22

Please refer to WISE-ED22 for flash programming.

Programming through WISE-ED20

Running Flash Loader Installer

Step01: Find installer flash_loader_demo_v2.9.0RC1.exe” in source tree, run it to install tool and set installation directory to default as below.